Re: Squeeze: max. 800x600 Auflösung
Am Sat, 30 Oct 2010 hat Michael Limburg folgendes geschrieben:
Wo werden da die möglichen Auflösungen des Monitors aufgelistet?
Der Monitor is für mich immer nur ein Teil gewesen das da in der Gegend
rumsteht und tut was man (bzw. die Grafikkarte) ihm sagt. Aber du hast
natürlich recht:
Daten, die der Monitor hergibt, kannst Du mittels der Tools aus dem
Paket read-edid auslesen.
Ausgabe bei mir: siehe unten (*)
Aber bitte die manpage lesen.
Klingt bedrohlich, in der man-Page steht aber nix Wichtiges drin soweit
ich das beurteilen kann. Installieren, aufrufen, fertig.
Und sollte daraus nicht (zumindest prinzipiell) auch eine eindeutige
Zuordnung zu einer funktionierenden X-Konfiguration hergestellt werden
können?
Du hattest eine funktionierende Konfiguration, wenn auch nur 800x600.
Äh, ja. Mit "funktionierend" meinte ich natürlich eine dem heutzutage der
Kommandozeile und dem Textmodus bereits völlig entfremdeten Weichei
gefällige Auflösung von oberhalb 1024x768.
Aber du hast natürlich (schon wieder!) recht ;-)
Jan.
(*) Ausgabe von "get-edid | parse-edid":
---------------------------------------------------
get-edid: get-edid version 1.4.1
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0xc5743 "Matrox Graphics Inc."
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination does not support DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call failed
The EDID data should not be trusted as the VBE call failed
EDID claims 19 more blocks left
EDID blocks left is wrong.
Your EDID is probably invalid.
parse-edid: EDID checksum failed - data is corrupt. Continuing anyway.
parse-edid: first bytes don't match EDID version 1 header
parse-edid: do not trust output (if any).
# EDID version 19 revision 19
Section "Monitor"
Identifier "DXS:1313"
VendorName "DXS"
ModelName "DXS:1313"
# DPMS capabilities: Active off:no Suspend:no Standby:no
Mode "275x275" # vfreq 43.295Hz, hfreq 45.979kHz
DotClock 48.830000
HTimings 275 294 313 1062
VTimings 275 276 327 1062
EndMode
Mode "275x275" # vfreq 43.295Hz, hfreq 45.979kHz
DotClock 48.830000
HTimings 275 294 313 1062
VTimings 275 276 327 1062
EndMode
Mode "275x275" # vfreq 43.295Hz, hfreq 45.979kHz
DotClock 48.830000
HTimings 275 294 313 1062
VTimings 275 276 327 1062
EndMode
Mode "275x275" # vfreq 43.295Hz, hfreq 45.979kHz
DotClock 48.830000
HTimings 275 294 313 1062
VTimings 275 276 327 1062
EndMode
EndSection
Reply to: