-------- Original Message -------- Subject: Re: sarge installer ver. 03/10/2004 Date: Sat, 13 Mar 2004 22:55:57 +0100 From: steef <steefvanduin@zonnet.nl> Reply-To: steefvanduin@zonnet.nl Organization: zetaTo: Hugo Vanwoerkom <hvw59601@care2.com>, Debian-User <debian-user@lists.debian.org> References: <[🔎] c2sk2i$b3o$1@sea.gmane.org> <[🔎] 4052317F.3000607@zonnet.nl> <[🔎] c2tegq$d2e$1@sea.gmane.org> <[🔎] E1B23nR-0007XP-K3@smtp5.home.nl> <[🔎] c2v899$p24$1@sea.gmane.org>
Hugo Vanwoerkom wrote:
steef wrote:On Friday 12 March 2004 23:44, Hugo Vanwoerkom wrote:steef wrote:Hugo Vanwoerkom wrote:<snip>on my machine i got the sarge-installer running after manually selecting a root partition __and___ defining the file-type manually. (this after ' partitioning' of course) did you do so too? i could not make that upout of your message. steefSteef:<snip>Steef: I cannot figure out how to not partition and define the file-type manually. He flips automagically from the beginning to "partitioning disks". There I get the choice of letting him do it or doing it manually. I hit "go back" then and select "Configure and mount partitions". Then he displays all the partitions he found. An aside: he cannot figure out hda1, although cfdisk shows it as:Partition Table for /dev/hda First Last# Type Sector Sector Offset Length Filesystem Type (ID) Flags -- ------- -------- --------- ------ --------- ---------------------- ---------1 Primary 0 8385929 63 8385930 Linux (83) Boot (80)2 Primary 8385930 40017914 0 31631985 Win95 Ext'd (LBA) (0F) None (00)5 Logical 8385930 16771859 63 8385930 Win95 FAT32 (0B) Boot (80) 6 Logical 16771860 27165914 63 10394055 Linux (83) Boot (80) 7 Logical 27165915 28483244 63 1317330 Linux swap (82) None (00) 8 Logical 28483245 40017914 63 11534670 Linux (83) Boot (80)There I select partition 13 on hdb and he gives me a bunch of choices for the mountpoint, not the file-type, I make it / and hit enter.After that he installs everything and the kernel-image which fails by saying that mkinitrd cannot find the root device.Where did you specify the file-type of the root device? Hugo
hello hugo.well ......to answer your [at last] question - after a couple of tests on two hd's, one with and one without windowz, with two different sarge-installers:
i specified the fs of the root dev on1. an empty, completely new partition (black-boxcfdisk; installing sarge, _manually_ and 2. on/selecting an existing linux partition, following the same procedure with _both_ installers; different from each other, of which one the beta-2.
in both cases i did not 'leave fs.' in the little blue box of the installer, but asked installer to make resp. ext3 and in another test reiserfs. then i 'clicked' again on the new fs's in the blue box and set one partition as root /, another as /home and a third as swapspace. this worked fine in both cases.
....till i rebooted the machine with the hd on which -now- sarge and windowz. no hard disk recognized!! in all cases. logically makes that the chanze a small one that the cause of -not recognizing a hd - is the hardware of my relative new and fast computer. the only time my machine rebooted normally was with a hd on which only, _ONLY_ sarge.
in all cases partitioning automatically flipped completely: no hd's recognized.
so i consider the installer far from mature and most discouraging for the less philosophical characters of the human kind.
and, at last: i hope you understand my english. k.r., steef3. with the aumatic installer i did not come anywhere, during installing sarge this part of the sarge-installer did not recognize my hd's in two occasions.