Re: PCMCIA network card with woody install
On Sun, 14 Jul 2002 11:32:59 -0400
Seneca <seneca-cunningham@rogers.com> wrote:
> On Sun, Jul 14, 2002 at 08:05:12AM -0700, Shawn Dunn wrote:
> > On Sun, 14 Jul 2002 10:19:34 -0400
> > Seneca <seneca-cunningham@rogers.com> wrote:
> >
> > > On Sat, Jul 13, 2002 at 09:33:50PM -0700, Shawn Dunn wrote:
> > > > On Sat, 13 Jul 2002 23:42:50 -0400
> > > > Seneca <seneca-cunningham@rogers.com> wrote:
> > > >
> > > >
> > <snip>
> > > > > > > pcmcia-cs/FAQ.Debian.gz). 2.2.20 (defualt woody kernel)
> > > > > >
> > > >
> > > > > > Ok, so here goes, managed to get it to boot w/o pcmcia
> > > > > > enabled, if I'modprobe i82365' I get a kernel panic, and
> > > > > > have to reboot, if I'insmod i82365' I get the following:
> > > > > >
> > > > > > max:/lib/modules/2.2.20/pcmcia# insmod i82365
> > > > > > Using /lib/modules/2.2.20/pcmcia/i82365.o
> > > > > > /lib/modules/2.2.20/pcmcia/i82365.o: unresolved symbol
> > > > > > pci_set_power_state...so on and so forth for about ten lines
> > > > > > of unresolved symbols
> > > > > >
> > <snip>
> > > > >
> > > > > > vendor. Ok, so I assume that there's a module not yet
> > > > > > loaded, and do an 'insmod pcmcia_core' and another kernel
> > > > > > panic.......
> > > > >
> > > > > Your assumption about the unresolved symbols is correct,
> > > > > i82365 requires pcmcia_core.
> > > > >
> > <snip>
> > > > > I have put the 2.2.20 kernel that is in woody on this system
> > > > > (a laptop that uses i82365 for the bridge). However, I have
> > > > > have not seen it panic (even after multiple boots). So, what
> > > > > does it say when the kernel panics (it probably says something
> > > > > more than just"kernel panic")?
> > > > >
> > > > Ok, a couple screens worth of what I would assume to be debuggin
> > > > symbols, and these are the last 4 lines of the kernel panic
> > > > (after setting /etc/default/pcmcia to pcmcia="yes" and
> > > > rebooting).
> > > >
> > > > Code: 8b 41 04 85 c9 74 22 8b 5a 18 8b 02 89 01 8b 0a 85 c9 74
> > > > 08 Aiee, killing interrupt handler
> > > > Kernel Panic: Attempted to kill the idel task!
> > > > In interrupt handler - not syncing
> > > >
> > > >
> > > > and that's it, right after INIT starts the pcmcia services (I
> > > > think, it flashes into the debug for the kernel awful quick)
> > >
> > > Those messages show a definite problem. The last time I saw a line
> > > starting with "Code: ", my kernel Oopsed.
> > >
> > > What does it say before the registers && the stack? (you might
> > > need to set up a serial console, but scroll lock should work after
> > > init starts if you don't mind using pen && paper) What do your
> > > logs say (I'm wondering about what they said for the successful
> > > boot with pcmcia)?
> > >
> > ok, how would I go about setting up a serial console, I have all PPC
> > machines here, and one lonely i386 (486 running Slackware 8,
> > headless), can I just string a serial cable to the Slack box, or is
> > there something I'm going to need to boot into single user and
> > change on the laptop???
>
> On the laptop's kernel command line, you need to put (going from the
> kernel documentation):
>
> console=device,options
>
> device: tty0 for the foreground virtual console
> ttyX for any other virtual console
> ttySx for a serial port
> options: depend on the driver. For the serial port this
> defines the baudrate/parity/bits of the port,
> in the format BBBBPN, where BBBB is the speed,
> P is parity (n/o/e), and N is bits. Default is
> 9600n8. The maximum baudrate is 115200.
>
> A serial console from my laptop could have "console=ttyS0,9600n8" on
> the kernel command line.
>
> The log entries will also help
Ok, pardon my ignorance here, it's been ages since I've used minicom,
how do I force it to listen to the serial port? (and how do I
determine which serial device I should be using?) I've tried every
permutation of devices I can think of, and no luck yet.....
...Bashing his head against the toughbook....
--Shawn
--
To UNSUBSCRIBE, email to debian-user-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: