USB-Stick
Hallo,
ich versuche hier gerade, meinen neuen USB-Stick auf einem amd64-Debian zum
Laufen zu kriegen. Und obwohl ich gerade über eine Stunde mit google befragen
und probieren beschäftigt war, bin ich noch keinen Schritt weiter:
fdisk -l bringt nur Partitionen in /dev/hda (die Festplatte), dementsprechend
komme ich auch bei meinen Versuchen, ihn zu mounten nur zu einem "dev/sda is
not a valid block device". Also anscheinend wird er nichtmal erkannt.
lsmod sagt:
eiswiese:/home/wol# lsmod
Module Size Used by
usb_storage 43840 0
vfat 13376 0
fat 42592 1 vfat
hotplug habe ich installiert, ich nehme an dass man da außer apt-get install
hotplug nichts machen muß? Wenn ich den Stick einstecke, kommen weder in
syslog noch in messages irgendwelche Meldungen :-(
Die relevanten Teile von dmesg habe ich unten angehängt.
Der Stick ist ein 1GB-Modell von Toshiba. Was mich etwas unruhig macht, ist
folgender Passus im Handbuch: "Das Produkt arbeitet nicht mit anderen
Betriebssystemen als Microsoft Windows". Ist das ernst zu nehmen, kann es
also sein, dass ich gar keine Chance habe, ihn zum Laufen zu kriegen?
Ich habe (noch) einen selbstkompilierten Kernel 2.6.9 - ist der zu alt? Wenn
es irgendwie ginge, würde ich das installieren eines neuen Kernels gerne auf
die Zeit nachdem dieser USB-Stick endlich läuft verschieben...
Schonmal danke für Hilfe und nehmt mich bitte ins cc, da ich nicht auf der
Liste bin.
Wolfgang
eiswiese:/home/wol# dmesg
[...]
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc
ports=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: capability 0001 at 68
ehci_hcd 0000:00:10.4: irq 21, pci mem ffffff0000012400
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: reset command 080022 (park)=0 ithresh=8 Async
period=1024 Reset HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:10.4: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.9 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0000000000001800
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.9 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 0000000000001c00
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
usb usb3: Manufacturer: Linux 2.6.9 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.0: port 1 portsc 018a
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.2: irq 21, io base 0000000000002000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#3)
usb usb4: Manufacturer: Linux 2.6.9 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#4)
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.0: port 2 portsc 018a
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.3: irq 21, io base 0000000000002400
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: detected 2 ports
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: default language 0x0409
usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#4)
usb usb5: Manufacturer: Linux 2.6.9 uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.1: port 1 portsc 008a
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 008a
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 1 portsc 008a
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
input: PS/2 Logitech Mouse on isa0060/serio1
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 140k freed
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.3: port 1 portsc 018a
hub 5-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
Losing some ticks... checking if CPU frequency changed.
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.3: port 2 portsc 008a
hub 5-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
warning: many lost ticks.
Your time source seems to be instable or some driver is hogging interupts
rip __do_softirq+0x48/0xb0
uhci_hcd 0000:00:10.0: suspend_hc
uhci_hcd 0000:00:10.1: suspend_hc
uhci_hcd 0000:00:10.2: suspend_hc
uhci_hcd 0000:00:10.3: suspend_hc
Adding 2097136k swap on /dev/hda5. Priority:-1 extents:1
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda6, internal journal
ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdd: No disk in drive
mtrr: no MTRR for f6000000,1000000 found
ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdd: No disk in drive
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
eiswiese:/home/wol#
Reply to: