Re: netzwerkkarte will nicht :((
Mein Mailserver hatte 'nen Plattencrash; weiss nicht ob diese email versendet wurde ...
"A.C. Almeida" schrieb:
> > Hi,
>
> OK, OK, habe ich wohl auch etwas mißverstanden ...
>
> Hier nun die Outputs:
>
> Bootvorgang, und siehe: da ist die karte
> schnipp
> ...
> ne.c:v1.10 9/23/94 Donald Becker (becker@scyld.com)
> Last modified Nov 1, 2000 by Paul Gortmaker
> NE*000 ethercard probe at 0x260: 52 54 40 28 e0 ac
> eth0: NE2000 found at 0x260, using IRQ 4.
> ...
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 8192 bind 8192)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> ...
> schnipp
>
> ifconfig >
> eth0 Link encap:Ethernet HWaddr 52:54:40:28:E0:AC
> inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> Interrupt:4 Base address:0x260
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:4 errors:0 dropped:0 overruns:0 frame:0
> TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:518 (518.0 b) TX bytes:518 (518.0 b)
> route>
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> localnet * 255.255.255.0 U 0 0 0 eth0
> default router 0.0.0.0 UG 0 0 0 eth0
>
> und die config-Datei
> # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
> # The loopback interface
> auto lo
> iface lo inet loopback
> #
> auto eth0
> iface eth0 inet static
> address 192.168.1.5
> netmask 255.255.255.0
> network 192.168.1.0
> broadcast 192.168.1.255
> gateway 192.168.1.1
>
> Also: Rechneradresse ist die 192.168.1.5; der Router hat die 192.168.1.1, soweit alles
> i.O.
>
> Ping liefert "time out"; modprobe -r eth0 liefert keine Fehlermeldung; ISA-Karte ist
> IRQ=4 und IO=0x260
>
> Tja und nun weiss ich nicht weiter ... :(( Das schlaue Linux-Buch von Marco Budde hilft
> mir auch nicht weiter.
>
> Gruß
>
> Antonio
>
> >
> > Ach, ich glaube, hier wurde meine Frage falsch verstanden: Ich meinte,
> > warum muss ich das Modul neu laden, damit ich die Netzwerkkarte nutzen
> > kann, nicht warum ich die Frage beantworten muss...
> >
> > Gruß
> > Holger
> >
> > --
> > Zum AUSTRAGEN schicken Sie eine Mail an debian-user-german-request@lists.debian.org
> > mit dem Subject "unsubscribe". Probleme? Mail an listmaster@lists.debian.org (engl)
Reply to: