Am Sonntag, 27. April 2003 14:42 schrieb Michael Grenier:
Multiple problems including no sound, doesn't like the second IDE
controller card, etc. However, my ignorance of Linux
prevents me really understanding the issue with some of them so I need
to ask help. Let's focus on sound first.
This is a BIOSTAR mothboard with imbedded LAN, Modem, and sound support.
----
1st problem - no sound. The sound imbedded on the mother board is listed
as:
VIA Technologies | VT8233 [AC97 Audio Controller], driver=via82cxxx_audio
and I get the error
modprobe: modprobe: Can't locate module sound-slot-0
modprobe: modprobe: Can't locate module sound-service-0-0
On newer ISOs (see changelog on servers) a new cheatcode called alsa was
introduced. This does activate the alsa-soundsystem, which supports some
newer chipsets (including many of the ac97-ones).
So you could try to use the "knoppix alsa" cheatcode at boot-prompt from CD.
cu
Fabian
PS: If you have any problems with alsa-support, please contact me.
This occurs when booting from the KNOPPIX CD. When attemping to use
sound such as playing the ogg file on the CD, xmms reports that the
sound card is not configured.
-------
2nd issue - while there appear to be various hardware isssues. I need to
ask the dumb question - how to major and
minor device numbers get assigned in Linux. Back in my days working on
Microport UNIX (SVR4), we set the major
number up explicitly in the kernel and the minor numbers were assigned
via the driver itself. Now, I'm trying to understand
the device /dev/dsp. If I have mulitple sound cards, how do the minor
numbers get setup? I have installed KNOPPIX
using the knx-install script and now I get Can not open device errors. I
used to get Solo1 device timeout errors but I've been swapping sound
cards in and out and now I'm not sure whats linked together.
-Mike Grenier
mwgrenier@yahoo.com
Output from dmesg when booting from Knoppix CD dated 4/18/03
Linux version 2.4.20-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mit Mär 26 15:37:36 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f4bc0
hm, page 000f4000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz alsa
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Initializing CPU#0
Detected 1533.115 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3060.53 BogoMIPS
Memory: 515360k/524224k available (1270k kernel code, 8476k reserved, 503k data, 128k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU0: AMD Athlon(tm) XP 1800+ stepping 02
per-CPU timeslice cutoff: 731.39 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-11, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178002
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0002
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 001 01 0 0 0 0 0 1 1 71
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 79
0d 001 01 0 0 0 0 0 1 1 81
0e 001 01 0 0 0 0 0 1 1 89
0f 001 01 0 0 0 0 0 1 1 91
10 001 01 1 1 0 1 0 1 1 99
11 001 01 1 1 0 1 0 1 1 A1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 B1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1533.0870 MHz.
..... host bus clock speed is 266.6238 MHz.
cpu: 0, clocks: 2666238, slice: 1333119
CPU0<T0:2666224,T1:1333104,D:1,S:1333119,C:2666238>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3099] at 00:00.0
PCI->APIC IRQ transform: (B0,I9,P0) -> 17
PCI->APIC IRQ transform: (B0,I17,P0) -> 16
PCI->APIC IRQ transform: (B0,I17,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P2) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:11.2, from 5 to 3
PCI: Via IRQ fixup for 00:11.3, from 5 to 3
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe0000000, mapped to 0xe080d000, size 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:0f3e
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 89
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
hdb: C/H/S=38309/16/255 from BIOS ignored
hda: ST317242A, ATA DISK drive
hdb: WDC WD800BB-00CAA1, ATA DISK drive
hdc: LTN526D, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-32123S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 33683328 sectors (17246 MB) w/512KiB Cache, CHS=2096/255/63
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63
ide-cd: passing drive hdc to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
Partition check:
hda: hda1 hda2
hdb: hdb1 hdb2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITEON Model: CD-ROM LTN526D Rev: YSR5
Type: CD-ROM ANSI SCSI revision: 02
Vendor: LITE-ON Model: LTR-32123S Rev: XS0R
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 465k freed
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
megaraid: v1.18 (Release Date: Thu Oct 11 15:02:53 EDT 2001)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Welcome to cloop v0.68
cloop: /cdrom/KNOPPIX/KNOPPIX: 28988 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 1 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 128k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
unloading Kernel Card Services
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:50:01 Mar 26 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
hub.c: new USB device 00:11.2-1, assigned address 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:11.2-1, assigned address 3
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: irq 7 detected
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe4851000, 00:40:f4:54:90:43, IRQ 17
eth0: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
PCI: Setting latency timer of device 00:11.5 to 64
Adding Swap: 915696k swap-space (priority -1)
Adding Swap: 1024088k swap-space (priority -2)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Output from dmesg using a hard disk boot:
Linux version 2.4.20-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mit Mär 26 15:37:36 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f4bc0
hm, page 000f4000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Kernel command line: BOOT_IMAGE=Linux ro root=301 hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Initializing CPU#0
Detected 1533.070 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3060.53 BogoMIPS
Memory: 515680k/524224k available (1270k kernel code, 8156k reserved, 503k data, 128k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU0: AMD Athlon(tm) XP 1800+ stepping 02
per-CPU timeslice cutoff: 731.39 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-11, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178002
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0002
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 001 01 0 0 0 0 0 1 1 71
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 79
0d 001 01 0 0 0 0 0 1 1 81
0e 001 01 0 0 0 0 0 1 1 89
0f 001 01 0 0 0 0 0 1 1 91
10 001 01 1 1 0 1 0 1 1 99
11 001 01 1 1 0 1 0 1 1 A1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 B1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1533.0870 MHz.
..... host bus clock speed is 266.6236 MHz.
cpu: 0, clocks: 2666236, slice: 1333118
CPU0<T0:2666224,T1:1333104,D:2,S:1333118,C:2666236>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3099] at 00:00.0
PCI->APIC IRQ transform: (B0,I9,P0) -> 17
PCI->APIC IRQ transform: (B0,I17,P0) -> 16
PCI->APIC IRQ transform: (B0,I17,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P2) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:11.2, from 5 to 3
PCI: Via IRQ fixup for 00:11.3, from 5 to 3
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe0000000, mapped to 0xe080d000, size 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:0f3e
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 89
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
hdb: C/H/S=38309/16/255 from BIOS ignored
hda: ST317242A, ATA DISK drive
hdb: WDC WD800BB-00CAA1, ATA DISK drive
hdc: LTN526D, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-32123S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 33683328 sectors (17246 MB) w/512KiB Cache, CHS=2096/255/63
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63
ide-cd: passing drive hdc to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
Partition check:
hda: hda1 hda2
hdb: hdb1 hdb2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITEON Model: CD-ROM LTN526D Rev: YSR5
Type: CD-ROM ANSI SCSI revision: 02
Vendor: LITE-ON Model: LTR-32123S Rev: XS0R
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 144k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 128k freed
Adding Swap: 915696k swap-space (priority -1)
Adding Swap: 1024088k swap-space (priority -2)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:50:01 Mar 26 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe494f000, 00:40:f4:54:90:43, IRQ 17
eth0: Identified 8139 chip type 'RTL-8139C'
solo1: version v0.19 time 15:49:36 Mar 26 2003
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
hub.c: new USB device 00:11.2-1, assigned address 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,66), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
blk: queue c032bfc4, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c032c110, I/O limit 4095Mb (mask 0xffffffff)
hub.c: new USB device 00:11.2-1, assigned address 3
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
-Mike