atheros-madwifi su debian etch/lenny
Penso di essere riuscito a sistemare la routing table (ps: perchè eth0 si connetteva anche senza route?), ma non mi si connette lo stesso (ho provato anche davanti all'ap con segnale massimo!)!
Qui sotto posto tutto quello che mi è venuto in mente di controllare!
Ho assegnato un indirizzo statico, ma nemmeno il dhcp va, e arping rimane lì a lampeggiare senza fare niente!
snoopy:/home/brunetto# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 192.168.0.1 255.255.255.0 UG 0 0 0 ath0
192.168.0.0
* 255.255.255.0 U 0 0 0 ath0
default 192.168.0.1 0.0.0.0 UG 0 0 0 ath0
snoopy:/home/brunetto# ifconfig
ath0 Link encap:Ethernet HWaddr 00:11:F5:A5:6C:86
inet addr:192.168.0.2 Bcast:192.168.0.255
Mask:255.255.255.0
inet6 addr: fe80::211:f5ff:fea5:6c86/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:380 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:36277 (35.4 KiB)
lo Link encap:Local Loopback
inet addr:
127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:358 errors:0 dropped:0 overruns:0 frame:0
TX packets:358 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:69935 (68.2 KiB) TX bytes:69935 (68.2 KiB)
wifi0 Link encap:UNSPEC HWaddr 00-11-F5-A5-6C-86-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17493 errors:0 dropped:0 overruns:0 frame:210
TX packets:653 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:199
RX bytes:2360403 (2.2 MiB) TX bytes:61149 (59.7 KiB)
Interrupt:177
snoopy:/home/brunetto# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11g ESSID:"WirelessZG"
Mode:Managed Frequency:2.412 GHz Access Point: 00:14:6C:62:D7:7E
Bit Rate:11 Mb/s Tx-Power:16 dBm Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:3541-4339-4332-4235-3333 Security mode:restricted
Power Management:off
Link Quality=13/94 Signal level=-74 dBm Noise level=-87 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
snoopy:/home/brunetto# iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 Interface doesn't support scanning.
wifi0 Interface doesn't support scanning.
ath0 Scan completed :
Cell 01 - Address: 00:14:6C:62:D7:7E
ESSID:"WirelessZG"
Mode:Master
Frequency:2.412 GHz (Channel 1)
Quality=19/94 Signal level=-76 dBm Noise level=-95 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s;
5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
sit0 Interface doesn't support scanning.
snoopy:/home/brunetto# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 *
255.255.255.0 U 0 0 0 ath0
snoopy:/home/brunetto# ping 192.168.0.1
PING 192.168.0.1 (
192.168.0.1) 56(84) bytes of data.
From 192.168.0.2 icmp_seq=2 Destination Host Unreachable
From 192.168.0.2 icmp_seq=3 Destination Host Unreachable
From 192.168.0.2 icmp_seq=4 Destination Host Unreachable
From 192.168.0.2 icmp_seq=6 Destination Host Unreachable
From
192.168.0.2 icmp_seq=7 Destination Host Unreachable
From 192.168.0.2 icmp_seq=8 Destination Host Unreachable
...
38 packets transmitted, 0 received, +27 errors, 100% packet loss, time 37001ms
, pipe 3
---------- Forwarded message ----------
From: automatic_jack <automatic_jack@katamail.com
>
Date: 28-mag-2007 11.31
Subject: Re: Fwd: Fwd: atheros-madwifi su debian etch/lenny
To: debian-italian@lists.debian.org
On Mon, 28 May 2007 10:50:03 +0200
"Brunetto Marco Ziosi" <brunettolist@gmail.com> wrote:
> non ero riuscito nemmeno con lìip statico, segna tutto ok ma non si
> connette, e per i problemi dhcp non saprei dove mettere le mani!
> Ho guardato un po il man di route ma non c'ho capito molto, come
> funzia?
Bhè, non so come funziona "in generale" ma per quel che lo ho
utilizzato...nel mio caso, che poi è speculare al tuo (solo che io ho
una configurazione statica) la tabella di routing ha due sole entry:
quella relativa all' interfaccia ath0 (caricata automaticamente) e
quella del default gataway che devi impostare a mano durante le prove
per poi automatizzarla:
#route add default gw GATEWAY_IP
l' ip del gateway deve essere pingabile (il gateway deve essere
raggiungibile)
Fa stà prova:
#ifcontig ath0
192.168.0.2
e vedi se ti fa pingare il gateway, se non funge installa "arping" e
vedi se con:
#arping -I ath0 GATEWAY_IP
ottiene qualcosa
Ciao :)
Reply to: