On Thu, Jun 14, 2001 at 09:46:38PM +0200, paolo massei wrote: > * mercoledì 13 giugno 2001, alle 21:17, Nicola Mariella scripsit: > > Ciao a tutti, qualcuno mi sa dire perche' quando inserisco il plug usb della stampante nella macchina mi da questo e non funzia? > > > > Jun 13 21:12:50 debian1 kernel: hub.c: USB new device connect on bus1/2, assigned device number 4 > > Jun 13 21:12:50 debian1 kernel: printer.c: usblp0: device node registration failed > > Jun 13 21:12:50 debian1 kernel: printer.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 > > > > Premetto che fino a qualche tempo fa andava alla perfezione. Ho installate le modutils e hotplug quindi quelle non dovrebbero essere a meno che non sia un problema di versione... Il device e' ok: mknod /dev/usb/lp0 c 180 0 > > > Domande a go-go: > > *) il "filesystem" usb viene montato? > Ho una riga che recita questo in /etc/fstab: > none /proc/bus/usb usbdevfs defaults 0 0 Si questo l'ho fatto. > > *) dmesg|less che dice? io ho una roba cosi': > uhci.c: USB UHCI at I/O 0xe400, IRQ 10 > uhci.c: detected 2 ports > usb.c: new USB bus registered, assigned bus number 1 > usb.c: kmalloc IF c256d640, numif 1 > usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1 > usb.c: USB device number 1 default language ID 0x0 > Product: USB UHCI-alt Root Hub > ecc. ecc. Questo e' quello che dice a me. Cmq non ci sono conflitti hardware perche' la quickcam va che e' un piacere. Ho anche messo il modulo printer per l'usb, ho pure provato a caricarlo a mano con modprobe e poi ho inserito il plug della stampante ma il messaggio e' sempre lo stesso. usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.259 $ time 07:53:36 Jun 14 2001 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 10 for device 00:07.2 PCI: The same IRQ used for device 00:0d.0 usb-uhci.c: USB UHCI at I/O 0x6400, IRQ 10 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: USB device 2 (vend/prod 0x5a9/0x511) is not claimed by any active driver. usb.c: registered new driver ov511 ov511.c: USB OV511 camera found ov511.c: camera: Lifeview RoboCam ov511.c: Sensor is an OV7610 ov511.c: ov511 driver version 1.28 registered > > *) il kernel ha le robe corrette nella pancia, tipo il supporto > per uhci oppure ohci (dare lspci -v per vedere qual'e' quello > necessario e per controllare eventuali conflitti di IRQ > > *) le direttive per los modules sono ben messe in /etc/modules.conf? > > *) hai provato ad inserire la spina-usb e *poi* a riavviare? Adesso provo quest'ultima spiaggia. > > Altro non mi viene, al momento... Grazie di tutto :) > -- > paolo massei > > ********************************************************************** > * The UNIX philosophy basically involves giving you enough rope to * > * hang yourself. And then a couple of feet more, just to be sure. * > ********************************************************************** > > > -- > To UNSUBSCRIBE, email to debian-italian-request@lists.debian.org > with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org > > -- Nicola Mariella email: nichi@linux.it PGP keyserver: keyring.debian.org
Attachment:
pgpqskOe9MaQv.pgp
Description: PGP signature