cdrecord - need for troubleshoot help

[linuksos <linuksos@gmail.com>]

Hello Guys,

I'm trying to erase and burn my cd-rw. I'm sure that there is no
problem with my cd-rw media as it works on my other system. After
unsuccessful attempt to burn it with k3b I have gone to command line
to see what is going on. For command line I have followed steps
described here:
http://www.linuxconfig.org/Create_and_burn_ISO_images_with_mkisofs_%26_cdrecord

Here is a output, everything looks fine but last 6 lines. Help is much
appreciated. Thank you

OUTPUT:


wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
TOC Type: 1 = CD-ROM
scsidev: '/dev/hdc'
devname: '/dev/hdc'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.2
SCSI buffer size: 64512
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'COMPAL  '
Identification : 'TSD80Y1 DVD RW  '
Revision       : 'D010'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM)
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1638400 = 1600 KB
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
Drive DMA Speed: 4449 kB/s 25x CD 3x DVD
FIFO size      : 12582912 = 12288 KB
Track 01: data   556 MB
Total size:      639 MB (63:21.21) = 285091 sectors
Lout start:      639 MB (63:23/16) = 285091 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 2
  Reference speed: 6
  Is not unrestricted
  Is erasable
  Disk sub type: High speed Rewritable (CAV) media (1)
  ATIP start of lead in:  -11077 (97:34/23)
  ATIP start of lead out: 359849 (79:59/74)
  1T speed low:  4 1T speed high: 10
  2T speed low:  2 2T speed high: 10
  power mult factor: 2 6
  recommended erase/write power: 5
  A1 values: 24 2C DC
  A2 values: 14 A4 4A
  A3 values: 04 C4 80
Disk type:    Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 74758
Speed set to 2116 KB/s
Starting to write CD/DVD at speed  12.0 in real TAO mode for single session.
Last chance to quit, starting real write    0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...


Errno: 0 (Success), send opc scsi sendcmd: no error
CDB:  54 01 00 00 00 00 00 00 00 00
status: 0x4 (CONDITION MET/GOOD)
cmd finished after 60.053s timeout 60s
wodim: OPC failed.
Writing  time:  174.939s



-- 
lubo
http://www.linuxconfig.org/