On Thu, Jun 05, 2003 at 07:04:59PM +0200, Takashi Iwai wrote: > ah, that's good to know. i should remove the pci id from emu10k1 > driver. > > do you have any chance to see what kind of chip exactly is that? > even though it's handled on software, there must be a CODEC and (very > likely) a DMA engine. i doubt Dell uses its truely unique chip. > it must be an OEM chip which is compatible with something... I couldn't find any relevant technical docs at Dell's site, but according to their FAQ it uses the "EMU10K1X software-accelerated Digital Signal Processor". The card lists the model as SB0200, and the chip has "EMU10K1X-DBQ" printed on it. Apparently there's also a SB0203 model, which is just a minor revision. For whatever it's worth, I've attached the output from lspci... I didn't see any relevant entries in /proc/dma. I've notified Dell that I intend to return the card for credit (haven't yet heard back), so if there's any more information you'd like to obtain please let me know ASAP. Alternately, if you'd prefer to examine the beastie firsthand, I'd be willing to forgo the credit and ship the card to you at my own expense. Again, I'll need to know fairly quickly if this is the case.
00:00.0 Host bridge: Intel Corp.: Unknown device 2578 (rev 02) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Capabilities: [e4] #09 [2106] Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp.: Unknown device 2579 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fd000000-feafffff Prefetchable memory behind bridge: f0000000-f7ffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- 00:1d.0 USB Controller: Intel Corp.: Unknown device 24d2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at ff80 [size=32] 00:1d.1 USB Controller: Intel Corp.: Unknown device 24d4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at ff60 [size=32] 00:1d.2 USB Controller: Intel Corp.: Unknown device 24d7 (rev 02) (prog-if 00 [UHCI]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 9 Region 4: I/O ports at ff40 [size=32] 00:1d.3 USB Controller: Intel Corp.: Unknown device 24de (rev 02) (prog-if 00 [UHCI]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at ff20 [size=32] 00:1d.7 USB Controller: Intel Corp.: Unknown device 24dd (rev 02) (prog-if 20 [EHCI]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 5 Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [20a0] 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fcf00000-fcffffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp.: Unknown device 24d0 (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 IDE interface: Intel Corp.: Unknown device 24db (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at ffa0 [size=16] Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K] 00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at fe00 [size=8] Region 1: I/O ports at fe10 [size=4] Region 2: I/O ports at fe20 [size=8] Region 3: I/O ports at fe30 [size=4] Region 4: I/O ports at fea0 [size=16] 00:1f.3 SMBus: Intel Corp.: Unknown device 24d3 (rev 02) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 3 Region 4: I/O ports at efe0 [size=32] 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) (prog-if 00 [VGA]) Subsystem: nVidia Corporation: Unknown device 01b6 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> 02:02.0 Multimedia audio controller: Creative Labs [SB Live! Value] EMU10k1X Subsystem: Creative Labs: Unknown device 1003 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 3 Region 0: I/O ports at df20 [size=32] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:02.1 Input device controller: Creative Labs [SB Live! Value] Input device controller Subsystem: Creative Labs: Unknown device 1003 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 0: I/O ports at df18 [size=8] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:08.0 Ethernet controller: Intel Corp.: Unknown device 1050 (rev 02) Subsystem: Dell Computer Corporation: Unknown device 0157 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), cache line size 10 Interrupt: pin A routed to IRQ 10 Region 0: Memory at fcfff000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at df40 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:00.0 Class 0600: 8086:2578 (rev 02) Subsystem: 1028:0157 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Capabilities: [e4] #09 [2106] Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none> 00:01.0 Class 0604: 8086:2579 (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fd000000-feafffff Prefetchable memory behind bridge: f0000000-f7ffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- 00:1d.0 Class 0c03: 8086:24d2 (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at ff80 [size=32] 00:1d.1 Class 0c03: 8086:24d4 (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at ff60 [size=32] 00:1d.2 Class 0c03: 8086:24d7 (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 9 Region 4: I/O ports at ff40 [size=32] 00:1d.3 Class 0c03: 8086:24de (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at ff20 [size=32] 00:1d.7 Class 0c03: 8086:24dd (rev 02) (prog-if 20) Subsystem: 1028:0157 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 5 Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [20a0] 00:1e.0 Class 0604: 8086:244e (rev c2) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fcf00000-fcffffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- 00:1f.0 Class 0601: 8086:24d0 (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 Class 0101: 8086:24db (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: 1028:0157 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at ffa0 [size=16] Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K] 00:1f.2 Class 0101: 8086:24d1 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at fe00 [size=8] Region 1: I/O ports at fe10 [size=4] Region 2: I/O ports at fe20 [size=8] Region 3: I/O ports at fe30 [size=4] Region 4: I/O ports at fea0 [size=16] 00:1f.3 Class 0c05: 8086:24d3 (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 3 Region 4: I/O ports at efe0 [size=32] 01:00.0 Class 0300: 10de:0181 (rev a2) Subsystem: 10de:01b6 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> 02:02.0 Class 0401: 1102:0006 Subsystem: 1102:1003 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 3 Region 0: I/O ports at df20 [size=32] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:02.1 Class 0980: 1102:7004 Subsystem: 1102:1003 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 0: I/O ports at df18 [size=8] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:08.0 Class 0200: 8086:1050 (rev 02) Subsystem: 1028:0157 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), cache line size 10 Interrupt: pin A routed to IRQ 10 Region 0: Memory at fcfff000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at df40 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Attachment:
pgpBUsOFY8Hg1.pgp
Description: PGP signature