[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Problem with Lucent winmodem on debian 2.2



Hi,

I am trying to configure Lucent Winmodem on my HP Pavillion (6735) box with
Debian 2.2. I have followed the instructions from www.linmodems.org for installing the binary only driver provided by Lucent, but still have problems in
loading the driver.

The following bits should tell the story.. Can someone help me out? The
modem is working fine with Windows ME.
 
I am not able to understand what exactly the problem is.
1. Why kernel module is not getting loaded. (Lucent's driver is supposed to support shared IRQ - Shouldn't it probe for the IRQ? Windows ME uses IRQ 3)
2. Why setserial complains about "No such device"


Thanks in advance,
Shaji


From insmod -f ltmodem
----------------------
Using /lib/modules/2.2.17/misc/ltmodem.o
Warning: kernel-module version mismatch
 /lib/modules/2.2.17/misc/ltmodem.o was compiled for kernel version
2.2.12-20
 while this kernel is version 2.2.17

/lib/modules/2.2.17/misc/ltmodem.o: init_module: Device or resource busy
Hint: this error can be caused by incorrect module parameters, including
invalid IO or IRQ parameters



From cat /proc/pci
------------------

    Communication controller: Lucent (ex-AT&T) Microelectronics Unknown
device
(rev 0).
      Vendor id=11c1. Device id=44e.
      Medium devsel.  Fast back-to-back capable.  Master Capable.
Latency=64.
Min Gnt=252.Max Lat=14.
      Non-prefetchable 32 bit memory at 0xf4100000 [0xf4100000].
      I/O at 0x3400 [0x3401].
      I/O at 0x3000 [0x3001].

From /etc/serial.conf
---------------------

# These are two spare devices you can use to customize for
# some board which is not supported above....
#
/dev/ttyS14 uart 16450 port 0x0260 irq 3
#/dev/ttyS15 uart XXXXX port XXXX irq X

From setserial -agv /dev/ttyS*
------------------------------
/dev/ttyS0, Line 0, UART: 16550A, Port: 0x03f8, IRQ: 4
 Baud_base: 115200, close_delay: 50, divisor: 0
 closing_wait: 3000
 Flags: spd_normal skip_test

/dev/ttyS1, Line 1, UART: unknown, Port: 0x02f8, IRQ: 3
 Baud_base: 115200, close_delay: 50, divisor: 0
 closing_wait: 3000
 Flags: spd_normal skip_test

/dev/ttyS14: No such device
/dev/ttyS2, Line 2, UART: unknown, Port: 0x03e8, IRQ: 4
 Baud_base: 115200, close_delay: 50, divisor: 0
 closing_wait: 3000
 Flags: spd_normal skip_test

/dev/ttyS3, Line 3, UART: unknown, Port: 0x02e8, IRQ: 3
 Baud_base: 115200, close_delay: 50, divisor: 0
 closing_wait: 3000
 Flags: spd_normal

From ls -l /dev/ttyS*
---------------------
crw-rw----    1 root     dialout    4,  64 Jul  5 23:14 /dev/ttyS0
crw-rw----    1 root     dialout    4,  65 Jul  5 23:14 /dev/ttyS1
crw-rw----    1 root     dialout    62,  78 Sep 28 05:42 /dev/ttyS14
crw-rw----    1 root     dialout    4,  66 Jul  5 23:14 /dev/ttyS2
crw-rw----    1 root     dialout    4,  67 Jul  5 23:14 /dev/ttyS3


Reply to: