ppp problem
Problem with ppp: 8-bit clean
I get a "Receive serial link is not 8-bit clean:
Problem: all had bit 7 set to 0"
with both a Sportster 28800 and a Worldport 14400.
I have also received an error-message saying:
Nov 29 19:28:57 pompel pppd[859]: Serial line is looped back
I start ppp with:
pppd connect 'chat -v "" ATDT22609101 CONNECT "" "name>" name "word>"
\qpassword' /dev/cua1 38400 -detach debug crtscts modem defaultroute
Why can the sportster do ~3200 cps with minicom, and refuse to connect
with ppp??
System
------
486/33 EISA with 16550A uarts.
Debian 0.93R6
Kernel 1.2.13
pppd 2.2.0
dmesg
-----
Console: colour EGA+ 80x25, 1 virtual console (max 63)
Calibrating delay loop.. ok - 16.77 BogoMips
Serial driver version 4.11 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16650
tty01 at 0x02f8 (irq = 3) is a 16650
PS/2 auxiliary pointing device detected -- driver installed.
snd3 <Pro AudioSpectrum 16D rev 63> at 0x388 irq 5 drq 3
snd2 <SoundBlaster 2.0> at 0x220 irq 7 drq 1
snd1 <Yamaha OPL-3 FM> at 0x388 irq 0 drq 0
Floppy drive(s): fd0 is 1.44M
FDC 0 is a pre-1991 82077
Configuring Adaptec at IO:3c80, IRQ 11
scsi0 : Adaptec 174x (EISA)
scsi : 1 host.
Vendor: TOSHIBA Model: MK537FB Rev: 6261
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, id 0, lun 0
Vendor: TOSHIBA Model: CD-ROM XM-3401TA Rev: 3593
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, id 1, lun 0
Vendor: ARCHIVE Model: Python 25501-XXX Rev: 2.26
Type: Sequential-Access ANSI SCSI revision: 01
Detected scsi tape st0 at scsi0, id 6, lun 0
scsi : detected 1 SCSI tape 1 SCSI cdrom 1 SCSI disk total.
SCSI Hardware sector size is 512 bytes on device sda
Memory: 14768k/16384k available (648k kernel code, 384k reserved, 584k data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.019
Swansea University Computer Society TCP/IP for NET3.019
IP Protocols: IGMP, ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 1.2.13 (root@pompel.pinet.no) (gcc version 2.6.3) #1 Thu Nov 2
17:15:20 MET 1995
Partition check:
sda: sda1 sda2 sda3
VFS: Mounted root (ext2 filesystem) readonly.
loading device 'eth0'...
eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 20 af 69 36 2d, IRQ 10.
3c509.c:1.03 10/8/94 becker@cesdis.gsfc.nasa.gov
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.2.0 (dynamic channel allocation)
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
SLIP: version 0.8.3-NET3.019-NEWTTY-MODULAR (4 channels) (6 bit encapsulation
enabled)
lp1 at 0x0378, using polling driver
Adding Swap: 14332k swap-space
eth0: Setting Rx mode to 1 addresses.
registered device ppp0
setserial
---------
/dev/cua1, UART: 16550A, Port: 0x02f8, IRQ: 3, Flags: spd_vhi
stty
----
speed 38400 baud; rows 25; columns 80; line = 0;
intr = ^C; quit = ^\; erase = <undef>; kill = <undef>; eof = ^D; eol =
<undef>;
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W;
lnext = ^V; flush = ^O; min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread clocal crtscts
ignbrk -brkint ignpar -parmrk -inpck istrip -inlcr -igncr -icrnl -ixon -ixoff
-iuclc -ixany -imaxbel -opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill
-ofdel nl0 cr0 tab0 bs0 vt0 ff0 -isig -icanon -iexten -echo -echoe -echok
-echonl -noflsh -xcase -tostop -echoprt -echoctl -echoke
daemon.log
----------
Nov 29 20:05:27 pompel pppd[1153]: pppd 2.2.0 started by root, uid 0
Nov 29 20:05:45 pompel pppd[1153]: Serial connection established.
Nov 29 20:05:46 pompel pppd[1153]: Using interface ppp0
Nov 29 20:05:46 pompel pppd[1153]: Connect: ppp0 <--> /dev/cua1
Nov 29 20:05:46 pompel pppd[1153]: sent [LCP ConfReq id=0x1 <mru 1500>
<asyncmap 0xa0000> <magic 0xe2ae1828> <pcomp> <accomp>]
Nov 29 20:06:13 pompel last message repeated 9 times
Nov 29 20:06:16 pompel pppd[1153]: LCP: timeout sending Config-Requests
Nov 29 20:06:16 pompel pppd[1153]: Connection terminated.
Nov 29 20:06:16 pompel pppd[1153]: Receive serial link is not 8-bit clean:
Nov 29 20:06:16 pompel pppd[1153]: Problem: all had bit 7 set to 0
Nov 29 20:06:16 pompel pppd[1153]: Exit.
messages
--------
Nov 29 20:05:44 pompel chat[1154]: ATDT22609101^M^M
Nov 29 20:05:44 pompel chat[1154]: CONNECT -- got it
Nov 29 20:05:44 pompel chat[1154]: send (^M)
Nov 29 20:05:44 pompel chat[1154]: expect (name>)
Nov 29 20:05:44 pompel chat[1154]: 28800/ARQ/V34/LAPM/V42BIS^M
Nov 29 20:05:45 pompel chat[1154]: Enter username> -- got it
Nov 29 20:05:45 pompel chat[1154]: send (username^M)
Nov 29 20:05:45 pompel chat[1154]: expect (word>)
Nov 29 20:05:45 pompel chat[1154]: username^M
Nov 29 20:05:45 pompel chat[1154]: ^GEnter user password> -- got it
Nov 29 20:05:45 pompel chat[1154]: send (qpassword^M)
As far as i know, the other side uses Ericsson 28800 v.34 modems, and I'm
the only one with this kind of problems.....
I had the same problems with Slackware 2.3
Thomas
(fed up..)
Reply to: