fallo en acceso a cdrom y grabadora
No consigo acceder ni al cdrom ni a la grabadora, no encuentro la
solución, ¿alguien puede darme pistas?
El equipo tiene un disco SATA (sda), un lector de DVD (hda) y una
grabadora de cd (hdc), el nucleo en el 2.6.9-1-686 precompilado de sid.
he probado a instalar udev y no cambia nada.
El accseso a compact Flash y discos duros no presenta problemas (discos
duros ide auxiliares)
cargando sr_mod ide-scsi cdrom sg sd-ide y cualguier otro modulo no
cambia nada, a continuación pegare la salida de dmesg y de lsmod por si
alguien me puede dar una pista
Module Size Used by
ide_cd 42592 0
cdrom 40956 1 ide_cd
nls_iso8859_1 3904 1
nls_cp437 5568 1
vfat 14528 1
fat 46624 1 vfat
ipt_MASQUERADE 3680 1
iptable_nat 26632 2 ipt_MASQUERADE
ip_conntrack 47892 2 ipt_MASQUERADE,iptable_nat
ip_tables 18560 2 ipt_MASQUERADE,iptable_nat
ipx 29772 0
lp 11080 0
binfmt_misc 11656 1
thermal 13000 0
fan 3812 0
button 6448 0
processor 17256 1 thermal
ac 4644 0
battery 9188 0
ds 18628 2
ipv6 264096 16
af_packet 22504 4
ohci_hcd 21412 0
pdc202xx_new 10908 0
e1000 87300 0
3c59x 39720 0
8139too 26240 0
8139cp 20768 0
mii 4928 2 8139too,8139cp
crc32 4192 2 8139too,8139cp
yenta_socket 21664 0
pcmcia_core 70484 2 ds,yenta_socket
matroxfb_base 32352 1
matroxfb_DAC1064 12640 1 matroxfb_base
matroxfb_accel 4928 1 matroxfb_base
matroxfb_Ti3026 6816 1 matroxfb_base
matroxfb_g450 7392 1 matroxfb_base
g450_pll 6816 2 matroxfb_DAC1064,matroxfb_g450
matroxfb_misc 9664 5
matroxfb_base,matroxfb_DAC1064,matroxfb_Ti3026,matroxfb_g450,g450_pll
snd_intel8x0 35276 0
snd_ac97_codec 73200 1 snd_intel8x0
snd_pcm_oss 54024 0
snd_mixer_oss 20192 1 snd_pcm_oss
snd_pcm 98696 2 snd_intel8x0,snd_pcm_oss
snd_timer 25668 1 snd_pcm
snd_page_alloc 9992 2 snd_intel8x0,snd_pcm
gameport 4512 1 snd_intel8x0
snd_mpu401_uart 7872 1 snd_intel8x0
snd_rawmidi 24900 1 snd_mpu401_uart
snd_seq_device 7976 1 snd_rawmidi
snd 56804 9
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 10176 1 snd
piix 13216 0
ehci_hcd 32068 0
uhci_hcd 32944 0
shpchp 101924 0
pciehp 98916 0
pci_hotplug 34448 2 shpchp,pciehp
intel_agp 22592 1
agpgart 34600 1 intel_agp
parport_pc 37188 1
parport 41704 2 lp,parport_pc
floppy 61072 0
tsdev 7648 0
mousedev 11576 2
psmouse 21960 0
pcspkr 3464 0
rtc 12664 0
evdev 9504 0
xfs 616216 1
md 48812 0
dm_mod 60252 0
capability 4392 0
commoncap 7008 1 capability
ext3 126184 2
jbd 64056 1 ext3
mbcache 9220 1 ext3
sd_mod 17904 7
usb_storage 69504 1
usbcore 119396 6 ohci_hcd,ehci_hcd,uhci_hcd,usb_storage
ide_core 143088 4 ide_cd,pdc202xx_new,piix,usb_storage
sg 38784 0
sata_sil 8036 4
libata 45540 1 sata_sil
scsi_mod 125676 4 sd_mod,usb_storage,sg,libata
unix 28564 363
fbcon 40416 71
font 8128 1 fbcon
vesafb 6656 0
cfbcopyarea 3936 2 matroxfb_accel,vesafb
cfbimgblt 2880 2 matroxfb_accel,vesafb
cfbfillrect 3584 2 matroxfb_accel,vesafb
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 152k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 209
ata1: SATA max UDMA/100 cmd 0xE081E080 ctl 0xE081E08A bmdma 0xE081E000
irq 209
ata2: SATA max UDMA/100 cmd 0xE081E0C0 ctl 0xE081E0CA bmdma 0xE081E008
irq 209
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003
88:207f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1(0): applying Seagate errata fix
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Using anticipatory io scheduler
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 506008k swap on /dev/sda5. Priority:-1 extents:1
EXT3 FS on sda2, internal journal
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, realtime, large block numbers,
no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
Real Time Clock Driver v1.12
input: PC Speaker
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
inserting floppy driver for 2.6.9-1-686
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel E7205 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xe8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 169, io base 0000d800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 177, io base 0000d000
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 185, io base 0000d400
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using address 2
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: IC Model: USB Storage-CFC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 250368 512-byte hdwr sectors (128 MB)
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 0
Vendor: IC Model: USB Storage-SMC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 1
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 1, type 0
Vendor: IC Model: USB Storage-MMC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 2, type 0
Vendor: IC Model: USB Storage-MSC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
Attached scsi generic sg4 at scsi2, channel 0, id 0, lun 3, type 0
USB Mass Storage device found at 2
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0
EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 193, pci mem e0850000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-1: USB disconnect, address 2
hw_random: RNG not detected
usb 2-1: new full speed USB device using address 3
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: IC Model: USB Storage-CFC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 250368 512-byte hdwr sectors (128 MB)
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
/dev/scsi/host3/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi3, channel 0, id 0, lun 0, type 0
Vendor: IC Model: USB Storage-SMC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi3, channel 0, id 0, lun 1
Attached scsi generic sg2 at scsi3, channel 0, id 0, lun 1, type 0
Vendor: IC Model: USB Storage-MMC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi3, channel 0, id 0, lun 2
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 2, type 0
Vendor: IC Model: USB Storage-MSC Rev: 301b
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sde at scsi3, channel 0, id 0, lun 3
Attached scsi generic sg4 at scsi3, channel 0, id 0, lun 3, type 0
USB Mass Storage device found at 3
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49538 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
matroxfb: Matrox G550 detected
matroxfb: MTRR's turned on
matroxfb: 640x480x8bpp (virtual: 640x26214)
matroxfb: framebuffer at 0xF0000000, mapped to 0xe0c00000, size 33554432
Console: switching to colour frame buffer device 80x30
fb0: MATROX frame buffer device
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 185
Yenta: CardBus bridge found at 0000:02:00.0 [0000:0000]
yenta 0000:02:00.0: Preassigned resource 0 busy, reconfiguring...
yenta 0000:02:00.0: Preassigned resource 2 busy, reconfiguring...
Yenta: ISA IRQ mask 0x0000, PCI irq 185
Socket status: 30000006
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:02:02.0 (id 10ec:8139 rev 10) is not an 8139C+
compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 22 (level, low) -> IRQ 209
eth0: RealTek RTL8139 at 0x9000, 00:40:f4:32:5d:54, IRQ 209
eth0: Identified 8139 chip type 'RTL-8139C'
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 185
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:04.0: 3Com PCI 3c905C Tornado at 0x9400. Vers LK1.1.19
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.3.19-k2
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 21 (level, low) -> IRQ 217
e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0322340(lo)
IPv6 over IPv4 tunneling driver
hw_random: RNG not detected
eth0: no IPv6 routers present
eth2: no IPv6 routers present
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: excluding 0x800-0x807
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x1f0-0x1f7
0x290-0x297 0x370-0x37f 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
ACPI: Processor [CPU0] (supports C1)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
lp0: using parport0 (interrupt-driven).
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
Device not ready. Make sure there is a disc in the drive.
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
Device not ready. Make sure there is a disc in the drive.
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
Device not ready. Make sure there is a disc in the drive.
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
program hddtemp is using a deprecated SCSI ioctl, please convert it to
SG_IO
NET: Registered protocol family 4
mtrr: no MTRR for f0000000,1000000 found
mtrr: no MTRR for f1000000,800000 found
mtrr: no MTRR for f1800000,800000 found
--
Antonio Trujillo Carmona <trujo@dti2.net>
Reply to: