Re: Erkennung CDBRENNER durch cdrecord ?

[Palfalvi Richard <richard.palfalvi@gmx.net>]

Hi!

Hier der Ausschnitt aus meiner lilo.conf von meinem Server:

image=/vmlinuz
        label=Linux
        read-only
        append="hdc=ide-scsi"

wie gesagt: nach dem Einfügen des append-kommandos habe ich lilo
ausgeführt und dann einen reboot gemacht.

thx für deine Hilfe.

mfg Richard

PS: im attachment meine gesamte lilo.conf

Am Mit, 2003-10-29 um 21.44 schrieb Andreas Janssen:
> Das hier stammt aus Deiner Ausgabe von dmesg:
> 
> Kernel command line: root=/dev/hda3 ro BOOT_IMAGE=linux.bin
> 
> dmesg | grep ide-scsi sagt bei mir:
> 
> Kernel command line: BOOT_IMAGE=Linux ro root=307 quiet hdc=ide-scsi
> hdd=ide-scsi max_scsi_luns=1
> ide_setup: hdc=ide-scsi
> ide_setup: hdd=ide-scsi
> hdc: attached ide-scsi driver.
> hdd: attached ide-scsi driver.
> 
> Bei Dir hingegen gar nichts. Also weiß der Kernel nicht, daß er ide-scsi
> für den Brenner verwenden soll. Und das dürfte auf eine
> Fehlkonfiguration Deines Bootloaders zurückzuführen sein - oder eben
> darauf, daß lilo nach der Änderung nicht ausgeführt wurde. Vielleicht
> postest Du mal den Abschnitt aus Deiner lilo.conf.

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
#    bios=0x81

#disk=/dev/sda
#    bios=0x80

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda1

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda3

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
#	prompt
#	single-key
#	delay=100
#	timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# example: append="hdc=ide-scsi hdd=ide-scsi"

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
	label=Linux
	read-only
	append="hdc=ide-scsi"

#	restricted
#	alias=1

image=/vmlinuz.old
	label=LinuxOLD
	read-only
	optional
#	restricted
#	alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#	label=HURD
#	restricted
#	alias=3
other=/dev/hda1
label="Linux(hda1)"