Re: Sun Fire V210 NIC's don't work
How about looking into OBP Config? Something like "test net" ?
I once had a similar Problem with a "hardcoded IP" (?) in OBP. Have you tried resseting your OBP and NVRAM?
My Blade 1500 silver shoudl have the same NIC and works just great, the missing Firmware Messages appeared but never had any Problem with them so i just ignored them.. ;)
Am 14.11.2012 um 19:38 schrieb Kaya Saman <kayasaman@gmail.com>:
> On 11/14/2012 06:25 PM, Richard Mortimer wrote:
>> On 14/11/2012 17:58, Kaya Saman wrote:
>>> On 11/14/2012 05:52 PM, Frans van Berckel wrote:
>>>> On Wed, 2012-11-14 at 17:14 +0000, Kaya Saman wrote:
>>
>> ...snip...
>>
>>> I can't ping anywhere from the eth1 interface :-(
>>>
>>> In addition I tried eth2 as the server has 4 NICs... it doesn't even get
>>> recognized by the system??
>>
>> Can you provide a few more bits of information.
>>
>> 1 - output from "prtconf -pv" That will give an OBP view of the system. I checked in DaveM's git tree and there isn't a sample from the v210 in there
>> https://git.kernel.org/?p=linux/kernel/git/davem/prtconfs.git;a=tree
>>
>> It would be good to push a copy of that to DaveM if you are agreeable.
>>
>> 2 - output from "ifconfig -a"
>>
>> 3 - output from "lspci"
>>
>> Regards
>>
>> Richard
>
> Hi Richard,
>
> # lspci
> 0000:00:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
> 0000:00:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
> 0001:00:06.0 Non-VGA unclassified device: ALi Corporation M7101 Power Management Controller [PMU]
> 0001:00:07.0 ISA bridge: ALi Corporation M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+]
> 0001:00:0a.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 0001:00:0d.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
> 0002:00:02.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 66MHz Ultra3 SCSI Adapter (rev 01)
> 0002:00:02.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 66MHz Ultra3 SCSI Adapter (rev 01)
> 0003:00:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
> 0003:00:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
>
>
> # ifconfig -a
> eth0 Link encap:Ethernet HWaddr 00:14:4f:5d:1e:7e
> inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:11450 errors:0 dropped:0 overruns:0 frame:0
> TX packets:6220 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1000502 (977.0 KiB) TX bytes:516835 (504.7 KiB)
> Interrupt:6
>
> eth1 Link encap:Ethernet HWaddr 00:14:4f:5d:1e:80
> BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> Interrupt:31
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:114 errors:0 dropped:0 overruns:0 frame:0
> TX packets:114 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:9542 (9.3 KiB) TX bytes:9542 (9.3 KiB)
>
>
>
> I have attached the prtconf file:
>
>
> Regards,
>
>
> Kaya
> <prtconf.txt>
Reply to: