On Thu, May 27, 2004 at 04:53:52PM +0200, Cedric Pradalier wrote:
> I undestand that it is not practical to compile a kernel just to test a
> module. So I just tried to make it available in a binary form.
>
> Can you try adding
>
> deb http://cedric.pradalier.free.fr/ibook2/ ./
>
> in you /etc/apt/sources.list file ?
>
> You should be able to install a package adm103x-module-2.6.6-powerpc,
> and eventually, after modprobing the therm_adm103x module, you can
> install wmadm, a small dockable app to monitor your ibook temperature.
>
> When loading therm_adm103x, it should output default parameter of the
> adm103x chip in syslog. Can you report them ? I wonder if this is a
> constant value for any ibook ?
>
> thanks.
Hi Cedric,
bored and courious as I'm sometimes in the office I downloaded and
installed 'adm103x-module-2.6.6-powerpc' on my Ibook G3 900Mhz Combo,
since i installed 2.6.6-powerpc customkernel just some days ago.
cheers float
===============================================================
wmadm shows temperatures around 54DegreeCelsius for 0 and around
47DegreeCelsius for 1,
===============================================================
syslog shows after modprobing the module:
bash-2.05b# cat /var/log/syslog | grep adm103
May 28 10:05:05 localhost kernel: therm_adm103x: no version for
"struct_module" found: kernel tainted.
May 28 10:05:05 localhost kernel: adm103x: Thermostat bus: 1, address: 0x2c
May 28 10:05:05 localhost kernel: adm103x: adm1030 initializing
May 28 10:05:05 localhost kernel: adm103x: adm1030 initializing 0:56+5°C
May 28 10:05:05 localhost kernel: adm103x: adm1030 initializing 1:68+10°C
================================================================
and admstate
bash-2.05b# admstate
Register 0x3D : 0x30
Device ID : 0x30
Register 0x3E : 0x41
Company ID : 0x41
Register 0x3F : 0x83
Therm-to-Fan enable : 1
Revision number : 3
Register 0x00 : 0xFD
Monitor : 1
!INT enable : 0
TACH/AIN : 1
PWM Inv : 1
Fan fault enable : 1
PWM Mode : Fastest Calculated Speed
Control Mode : Automatic
Register 0x01 : 0x7B
PWM1 enable : 1
TACH1 enable : 0
Loc Temp enable : 1
Remote1 Temp enable : 1
SW Reset : 0
Register 0x02 : 0x00
Alarm1 speed : 0
Fan1 fault : 0
Remote1 temp high : 0
Remote1 temp low : 0
Remote1 temp therm : 0
Remote1 diode error : 0
Loc temp high : 0
Loc temp low : 0
Register 0x03 : 0x20
Loc therm : 0
!THERM : 0
Register 0x06 : 0x03
Remote1 temp resolution : 0.375000
Local temp resolution : 0.000000
Register 0x08 : 0x00
Fan1 speed : inf rpm
Register 0x0A : 0x3A
Local temp : 58
Register 0x0B : 0x36
Remote1 temp : 54
Register 0x0D : 0x04
Local temp offset : 4
Register 0x0E : 0x08
Remote1 temp offset : 8
Register 0x10 : 0xFF
Fan1 Tach High limit : 255 -> 1.323529-0.661765
Register 0x14 : 0x3C
Local temp high limit : 60
Register 0x15 : 0x00
Local temp low limit : 0
Register 0x16 : 0x4F
Local temp therm limit : 79
Register 0x18 : 0x50
Remote1 temp high limit : 80
Register 0x19 : 0x00
Remote1 temp low limit : 0
Register 0x1A : 0x60
Remote1 temp therm limit : 96
Register 0x20 : 0x5A
Fan1 Spin Up : 0.600000 s
PWM Freqency : 31.250000 Hz
Speed range : 1324 rpm
Register 0x22 : 0x05
Fan1 min speed : 33 %
Register 0x23 : 0x51
Fan spin-up disable : 0
Ramp rate : 4
ADC sample rate : 1.000000 Hz
Fan1 filter enable : 1
Register 0x24 : 0x78
Local fan starting temp : 60
Local fan speeding range : 5
Register 0x25 : 0x99
Remote fan1 starting temp : 76
Remote fan1 speeding range: 10
--
-----------------------------------------------------------------------
_ | .''`.Florian Klinglmueller
ASCII ribbon campaign ( ) | : :' :debian-ppc user
- against HTML email X | `. `'`
& vCards / \ | `- float@jabber.org
------------------------------------------------------------------------
Attachment:
signature.asc
Description: Digital signature