Sleep problems in kernel 2.6 from mvista.com
Hello all,
Although is not a Debian-specific matter, I believe this is the place to
ask. I have a G3 Ibook with radeon (more details below). Recently I
switched to 2.6 branch (rsyncing to source.mvista.com) because I wanted to
have XFS in my laptop (I've had very good experiences in the desktop
machine).
The problem arises when I put the laptop into sleep/suspend. I try it in
tow ways: throught pmud and with a small sleep test I have (code listing
below, very short). It suspends fine but doesn't finish waking up; I can
hear the hard disk initial spin but after that the whole system freezes
(not even a network response). It used to happen in some versions of
2.4-benh but not all of them.
It can't be a hardware problem because it has been working fine with most
of the 2.4-benh kernels. I guess there must be some kernel configuration
mistake. I've tried both enabling and disabling APM emulation.
Thanks in advance and I apologize about the length of this message.
=== SYSTEM DATA ===
etanol@butterfly:~$ uname -a
Linux butterfly 2.6.0-test11 #8 Mon Dec 1 03:36:06 CET 2003 ppc GNU/Linux
etanol@butterlfy:~$ cat /proc/cpuinfo
processor : 0
cpu : 750FX
temperature : 1-76 C (uncalibrated)
clock : 600MHz
revision : 1.2 (pvr 7000 0102)
bogomips : 1189.47
machine : PowerBook4,3
motherboard : PowerBook4,3 MacRISC2 MacRISC Power Macintosh
detected as : 257 (iBook 2 rev. 2)
pmac flags : 0000000b
L2 cache : 512K unified
memory : 256MB
pmac-generation : NewWorld
etanol@butterlfy:~$ dmesg
Total memory = 256MB; using 512kB for hash table (at c0380000)
Linux version 2.6.0-test11 (root@butterfly) (gcc versión 3.3.2 (Debian)) #8
Mon Dec 1 03:36:06 CET 2003
Found Uninorth memory controller & host bridge, revision: 192
Mapped at 0xfdf3c000
Found a Pangea mac-io controller, rev: 0, mapped at 0xfdebc000
Processor NAP mode on idle enabled.
PowerMac motherboard: iBook 2 rev. 2
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
PMU driver 2 initialized for Core99, firmware: 0c
On node 0 totalpages: 65536
DMA zone: 65536 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Building zonelist for node : 0
Kernel command line: root=/dev/hda5 ro
PowerMac using OpenPIC irq controller
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc66e000
OpenPIC timer frequency is 4.160000 MHz
PID hash table entries: 2048 (order 11: 16384 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 24.835277 MHz
Console: colour dummy device 80x25
Memory: 255040k available (2348k kernel code, 1060k data, 132k init, 0k
highmem)
AGP special page: 0xcffff000
Calibrating delay loop... 1189.47 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: Probing PCI hardware
Registering openpic with sysfs...
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
radeonfb_pci_register BEGIN
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb: ref_clk=2700, ref_div=12, xclk=16615 from OF
radeonfb: probed DDR SGRAM 16384k videoram
radeonfb: detected DFP panel size from EDID: 1024x768
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon M6 LY DDR SGRAM 16 MB
radeonfb: DVI port LCD monitor connected
radeonfb: CRT port no monitor connected
radeonfb_pci_register END
Thermal assist unit using timers, shrink_timer: 200 jiffies
SGI XFS for Linux with no debug enabled
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910412
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
post div = 0x2
fb_div = 0x3a
ppll_div_3 = 0x1003a
ron = 1152, roff = 18256
vclk_freq = 6525, per = 652
Console: switching to colour frame buffer device 128x48
pty: 256 Unix98 ptys configured
Generic RTC Driver v1.07
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth/Pangea chipset
agpgart: Maximum main memory to use for agp memory: 204M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
[drm] Initialized radeon 1.9.0 20020828 on minor 0
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:93:2b:92
eth0: Found BCM5221 PHY
MacIO PCI driver attached to Pangea chipset
Macintosh non-volatile memory driver v1.0
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2
Probing IDE interface ide0...
hda: IBM-IC25N020ATCS04-0, ATA DISK drive
hdb: LG CD-ROM CRN-8245B, ATAPI CD/DVD-ROM drive
ide_pmac: Set UDMA timing for mode 2, reg: 0x1090038c
hda: Enabling Ultra DMA 2
ide_pmac: Set UDMA timing for mode 2, reg: 0x1090038c
hdb: Enabling Ultra DMA 2
Using anticipatory io scheduler
ide0 at 0xd22cd000-0xd22cd007,0xd22cd160 on irq 19
hda: max request size: 128KiB
adb: starting probe task...
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(33)
hda:<7>adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
[mac] hda1 hda2 hda3 hda4 hda5 hda6
end_request: I/O error, dev hdb, sector 0
ADB mouse at 3, handler set to 4hdb: ATAPI 24X CD-ROM drive, 128kB Cache,
UDMA(33)
Uniform CD-ROM driver Revision: 3.12
(trackpad)Console: switching to colour frame buffer device 128x48
ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0001:01:18.0 (0000 -> 0002)
ohci_hcd 0001:01:18.0: OHCI Host Controller
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ohci_hcd 0001:01:18.0: irq 27, pci mem d22d2000
ohci_hcd 0001:01:18.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0001:01:19.0 (0000 -> 0002)
ohci_hcd 0001:01:19.0: OHCI Host Controller
ohci_hcd 0001:01:19.0: irq 28, pci mem d22d4000
ohci_hcd 0001:01:19.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
XFS mounting filesystem hda5
Starting XFS recovery on filesystem: hda5 (dev: hda5)
Ending XFS recovery on filesystem: hda5 (dev: hda5)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 132k init 4k chrp 8k prep
Adding 524280k swap on /dev/hda4. Priority:-1 extents:1
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910410
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
post div = 0x2
fb_div = 0x3a
ppll_div_3 = 0x1003a
ron = 1632, roff = 18256
vclk_freq = 6525, per = 652
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910412
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
post div = 0x2
fb_div = 0x3a
ppll_div_3 = 0x1003a
ron = 1152, roff = 18256
vclk_freq = 6525, per = 652
hStart = 1048, hEnd = 1184, hTotal = 1344
vStart = 771, vEnd = 777, vTotal = 806
h_total_disp = 0x7f00a7 hsync_strt_wid = 0x910410
v_total_disp = 0x2ff0325 vsync_strt_wid = 0x860302
pixclock = 15384
freq = 6500
post div = 0x2
fb_div = 0x3a
ppll_div_3 = 0x1003a
ron = 1632, roff = 18256
vclk_freq = 6525, per = 652
etanol@butterfly:~$ cat /usr/src/benh_kernel/.config
#
# Automatically generated make config: don't edit
#
CONFIG_MMU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PPC=y
CONFIG_PPC32=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_STANDALONE=y
CONFIG_BROKEN_ON_SMP=y
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y
#
# Processor
#
CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
# CONFIG_8xx is not set
# CONFIG_ALTIVEC is not set
CONFIG_TAU=y
# CONFIG_TAU_INT is not set
# CONFIG_TAU_AVERAGE is not set
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_PROC_INTF is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_24_API is not set
CONFIG_CPU_FREQ_PMAC=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_PPC601_SYNC_FIX is not set
CONFIG_PM=y
CONFIG_PPC_STD_MMU=y
#
# Platform options
#
CONFIG_PPC_MULTIPLATFORM=y
# CONFIG_APUS is not set
# CONFIG_WILLOW is not set
# CONFIG_PCORE is not set
# CONFIG_POWERPMC250 is not set
# CONFIG_EV64260 is not set
# CONFIG_SPRUCE is not set
# CONFIG_LOPEC is not set
# CONFIG_MCPN765 is not set
# CONFIG_MVME5100 is not set
# CONFIG_PPLUS is not set
# CONFIG_PRPMC750 is not set
# CONFIG_PRPMC800 is not set
# CONFIG_SANDPOINT is not set
# CONFIG_ADIR is not set
# CONFIG_K2 is not set
# CONFIG_PAL4 is not set
# CONFIG_GEMINI is not set
# CONFIG_EST8260 is not set
# CONFIG_SBS8260 is not set
# CONFIG_RPX6 is not set
# CONFIG_TQM8260 is not set
CONFIG_PPC_CHRP=y
CONFIG_PPC_PMAC=y
CONFIG_PPC_PREP=y
CONFIG_PPC_OF=y
CONFIG_PPCBUG_NVRAM=y
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
# CONFIG_HIGHMEM is not set
CONFIG_KERNEL_ELF=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_PROC_DEVICETREE=y
# CONFIG_PPC_RTAS is not set
# CONFIG_PREP_RESIDUAL is not set
# CONFIG_CMDLINE_BOOL is not set
#
# Bus options
#
# CONFIG_ISA is not set
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Advanced setup
#
CONFIG_ADVANCED_OPTIONS=y
CONFIG_HIGHMEM_START=0xfe000000
# CONFIG_LOWMEM_SIZE_BOOL is not set
CONFIG_LOWMEM_SIZE=0x30000000
# CONFIG_KERNEL_START_BOOL is not set
CONFIG_KERNEL_START=0xc0000000
# CONFIG_TASK_SIZE_BOOL is not set
CONFIG_TASK_SIZE=0x80000000
CONFIG_BOOT_LOAD=0x00800000
#
# Generic Driver Options
#
# CONFIG_FW_LOADER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Plug and Play support
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_LBD is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_TASKFILE_IO=y
#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_SL82C105 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_BLINK=y
CONFIG_BLK_DEV_IDEDMA_PMAC_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_SCSI is not set
#
# Fusion MPT device support
#
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_IPV6 is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
CONFIG_CRC32=y
CONFIG_MACE=y
# CONFIG_MACE_AAUI_PORT is not set
# CONFIG_BMAC is not set
# CONFIG_OAKNET is not set
# CONFIG_HAPPYMEAL is not set
CONFIG_SUNGEM=y
# CONFIG_NET_VENDOR_3COM is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# Bluetooth support
#
# CONFIG_BT is not set
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
# CONFIG_FB_CONTROL is not set
# CONFIG_FB_PLATINUM is not set
# CONFIG_FB_VALKYRIE is not set
# CONFIG_FB_CT65550 is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_S3TRIO is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=y
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_PCI_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
# CONFIG_SERIO is not set
# CONFIG_SERIO_I8042 is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Macintosh device drivers
#
# CONFIG_ADB_CUDA is not set
CONFIG_ADB_PMU=y
CONFIG_PMAC_PBOOK=y
CONFIG_PMAC_APM_EMU=y
CONFIG_PMAC_BACKLIGHT=y
# CONFIG_MAC_FLOPPY is not set
# CONFIG_MAC_SERIAL is not set
CONFIG_ADB=y
CONFIG_ADB_MACIO=y
CONFIG_INPUT_ADBHID=y
CONFIG_MAC_EMUMOUSEBTN=y
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_PMACZILOG is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=64
#
# I2C support
#
# CONFIG_I2C is not set
#
# I2C Algorithms
#
#
# I2C Hardware Bus support
#
#
# I2C Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_QIC02_TAPE is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_NVRAM=y
CONFIG_GEN_RTC=y
CONFIG_GEN_RTC_X=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
CONFIG_AGP_UNINORTH=y
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=y
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_RAW_DRIVER is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_XFS_FS=y
# CONFIG_XFS_RT is not set
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_FAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS=y
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
# CONFIG_EXPORTFS is not set
CONFIG_SUNRPC=y
# CONFIG_SUNRPC_GSS is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
# CONFIG_MSDOS_PARTITION is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_NEC98_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-15"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_UHCI_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# SCSI support is needed for USB Storage
#
# CONFIG_USB_STORAGE is not set
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_XPAD is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GADGET is not set
#
# Library routines
#
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_BOOTX_TEXT=y
#
# Security options
#
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
Reply to: