kernel param et HD, et autres???
Bonjours,
Après avoir recompiler mon kernel j'ai commencé à éplucher les messages de boot et je me suis donc posé quelques questions.....
<Première_question>
Avec mon nouveau noyau (2.2.18pre21) j'obtient:
ALI15X3: IDE controller on PCI bus 00 dev 78
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: ST36531A, ATA DISK drive
hdc: IBM-DTLA-307030, ATA DISK drive
hdd: ATAPI CDROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ST36531A, 6204MB w/128kB Cache, CHS=790/255/63, UDMA
hdc: IBM-DTLA-307030, 29314MB w/1916kB Cache, CHS=59560/16/63, UDMA
(...)
Partition check:
hda:hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: DMA disabled
ide0: reset: success
hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc:hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: DMA disabled
hdd: DMA disabled
ide1: reset: success
[PTBL] [3737/255/63] hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
Alors qu'avec le précédent (par défaut à l'installe, 2.2.17), j'obtenais:
PCI_IDE: unknown IDE controller on PCI bus 00 device 78, VID=10b9, DID=5229
PCI_IDE: not 100% native mode: will probe irqs later
PCI_IDE: simplex device: DMA disabled
ide0: PCI_IDE Bus-Master DMA disabled (BIOS)
PCI_IDE: simplex device: DMA disabled
ide1: PCI_IDE Bus-Master DMA disabled (BIOS)
hda: ST36531A, ATA DISK drive
hdc: IBM-DTLA-307030, ATA DISK drive
hdd: ATAPI CDROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ST36531A, 6204MB w/128kB Cache, CHS=790/255/63
hdc: IBM-DTLA-307030, 29314MB w/1916kB Cache, CHS=59560/16/63
(..)
Partition check:
hda:hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: [PTBL] [3737/255/63] hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
La question toute bête qui me vient à l'esprit: quelles sont les paramètres qu'il faut que je passe au noyaux pour lui dire de disabler tout de suite le DMA, de plus dés la premiére erreur ma petite lumiére rouge (indications de l'accés disque) s'allume pour ne s'éteindre qu'à l'arret du système...Est-ce grave docteur?
NB: j'ai une configue un peu stange: je boot sur disquette et ma partition root est sur hdc3. J'ai joins les messages complets, au cas où........
<fin_première_question>
<deuxième_question>
à la fin de mes messages systèmes j'ai
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Bon d'accord, mais si je veux que cela se fasse automatiquement au démarrage je fais comment?
<fin_deuxième_question>
<troisième_question>
J'ai aussi:
arpwatch uses obsolete (PF_INET,SOCK_PACKET)
device eth0 entered promiscuous mode
Pour arpwatch je suppose qu'il faut attendre une update, je me trompe????
Pour le promiscuous mode je me demandais si arpwatch et autre snort avaient qqchose à voir???? ou si ce n'est pas normale du tout et à quoi ça pourrait être du.
<fin_troisième_question>
Merci encore....
Bruno D.Linux version 2.2.18pre21 (root@bubu) (gcc version 2.95.2 20000220 (Debian GNU/Linux)) #1 Tue Dec 12 22:38:37 CET 2000
Detected 334103 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 666.82 BogoMIPS
Memory: 95580k/98304k available (1060k kernel code, 412k reserved, 1192k data, 60k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
512K L2 cache (4 way)
CPU: L2 Cache: 512K
CPU: Intel Pentium II (Deschutes) stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfdb01
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
ALI15X3: IDE controller on PCI bus 00 dev 78
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: ST36531A, ATA DISK drive
hdc: IBM-DTLA-307030, ATA DISK drive
hdd: ATAPI CDROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ST36531A, 6204MB w/128kB Cache, CHS=790/255/63, UDMA
hdc: IBM-DTLA-307030, 29314MB w/1916kB Cache, CHS=59560/16/63, UDMA
hdd: ATAPI 36X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
scsi : 0 hosts.
scsi : detected total.
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xde00, IRQ 9.
eth0: RealTek RTL-8029 found at 0xde00, IRQ 9.
Partition check:
hda:hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: DMA disabled
ide0: reset: success
hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc:hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: timeout waiting for DMA
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: DMA disabled
hdd: DMA disabled
ide1: reset: success
[PTBL] [3737/255/63] hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 60k freed
Adding Swap: 184736k swap-space (priority -1)
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
arpwatch uses obsolete (PF_INET,SOCK_PACKET)
device eth0 entered promiscuous mode
Linux version 2.2.17 (herbert@arnor) (gcc version 2.95.2 20000313 (Debian GNU/Linux)) #1 Sun Jun 25 09:24:41 EST 2000
Detected 334103 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 666.83 BogoMIPS
Memory: 94600k/98304k available (1732k kernel code, 416k reserved, 1416k data, 140k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Deschutes) stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfdb01
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
apm: disabled on user request.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
PCI_IDE: unknown IDE controller on PCI bus 00 device 78, VID=10b9, DID=5229
PCI_IDE: not 100% native mode: will probe irqs later
PCI_IDE: simplex device: DMA disabled
ide0: PCI_IDE Bus-Master DMA disabled (BIOS)
PCI_IDE: simplex device: DMA disabled
ide1: PCI_IDE Bus-Master DMA disabled (BIOS)
hda: ST36531A, ATA DISK drive
hdc: IBM-DTLA-307030, ATA DISK drive
hdd: ATAPI CDROM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ST36531A, 6204MB w/128kB Cache, CHS=790/255/63
hdc: IBM-DTLA-307030, 29314MB w/1916kB Cache, CHS=59560/16/63
hdd: ATAPI 36X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0
Failed initialization of WD-7000 SCSI card!
IBM MCA SCSI: No Microchannel-bus support present -> Aborting.
megaraid: v107 (December 22, 1999)
aec671x_detect:
3w-xxxx: tw_findcards(): No cards found.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda:hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
hda1 hda2 hda3 hda4 < hda5 hda6 >
hdc: [PTBL] [3737/255/63] hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
NET4: Unix domain sockets 1.0 for Linux NET4.0.
Adding Swap: 184736k swap-space (priority -1)
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xde00, IRQ 9.
eth0: RealTek RTL-8029 found at 0xde00, IRQ 9.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
arpwatch uses obsolete (PF_INET,SOCK_PACKET)
device eth0 entered promiscuous mode
Reply to: