Re: disk going bad? or fuser related issues? . . .
On 10/9/19, Reco <recoverym4n@enotuniq.net> wrote:
> Please post the results of "smartctl -A".
>
> Reco
Here go the results for one of my drives (a Seagate Samsung 2.00 TB):
# smartctl --xall /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-6-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Samsung SpinPoint M9T
Device Model: ST2000LM003 HN-M201RAD
Serial Number: M932A4G7001730
LU WWN Device Id: 0 000000 000000000
Firmware Version: 2BE10001
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Oct 7 02:42:12 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (23580) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 393) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 088 086 025 - 3889
4 Start_Stop_Count -O--CK 100 100 000 - 525
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 1796
10 Spin_Retry_Count -O--CK 252 252 051 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 864
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 057 000 - 23 (Min/Max 19/43)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2
223 Load_Retry_Count -O--CK 100 100 000 - 1
225 Load_Cycle_Count -O--CK 098 098 000 - 23353
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xc0-0xdf GPL,SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 794 hours (33 days + 2 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 41 04 b1 00 00 49 46 0f 4f 40 00 Error: ICRC, ABRT at LBA =
0x49460f4f = 1229328207
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 04 00 00 00 49 46 10 00 40 00 00:00:08.814 WRITE FPDMA QUEUED
61 00 70 04 00 00 00 49 46 10 00 40 00 00:00:08.877 WRITE FPDMA QUEUED
61 00 70 04 00 00 00 49 46 0c 00 40 00 00:00:08.877 WRITE FPDMA QUEUED
61 00 70 04 00 00 00 49 46 08 00 40 00 00:00:08.877 WRITE FPDMA QUEUED
61 00 70 04 00 00 00 49 46 04 00 40 00 00:00:08.877 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has
ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 23 Celsius
Power Cycle Min/Max Temperature: 19/23 Celsius
Lifetime Min/Max Temperature: 19/44 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (102)
Index Estimated Time Temperature Celsius
103 2019-10-06 16:05 23 ****
104 2019-10-06 16:10 33 **************
105 2019-10-06 16:15 32 *************
106 2019-10-06 16:20 32 *************
107 2019-10-06 16:25 31 ************
108 2019-10-06 16:30 31 ************
109 2019-10-06 16:35 31 ************
110 2019-10-06 16:40 21 **
111 2019-10-06 16:45 22 ***
112 2019-10-06 16:50 22 ***
113 2019-10-06 16:55 23 ****
114 2019-10-06 17:00 23 ****
115 2019-10-06 17:05 24 *****
... ..( 11 skipped). .. *****
127 2019-10-06 18:05 24 *****
0 2019-10-06 18:10 23 ****
1 2019-10-06 18:15 23 ****
2 2019-10-06 18:20 23 ****
3 2019-10-06 18:25 24 *****
... ..( 3 skipped). .. *****
7 2019-10-06 18:45 24 *****
8 2019-10-06 18:50 23 ****
... ..( 5 skipped). .. ****
14 2019-10-06 19:20 23 ****
15 2019-10-06 19:25 24 *****
16 2019-10-06 19:30 24 *****
17 2019-10-06 19:35 24 *****
18 2019-10-06 19:40 23 ****
... ..( 8 skipped). .. ****
27 2019-10-06 20:25 23 ****
28 2019-10-06 20:30 24 *****
... ..( 7 skipped). .. *****
36 2019-10-06 21:10 24 *****
37 2019-10-06 21:15 25 ******
38 2019-10-06 21:20 27 ********
39 2019-10-06 21:25 28 *********
40 2019-10-06 21:30 28 *********
41 2019-10-06 21:35 29 **********
... ..( 2 skipped). .. **********
44 2019-10-06 21:50 29 **********
45 2019-10-06 21:55 27 ********
46 2019-10-06 22:00 26 *******
47 2019-10-06 22:05 25 ******
... ..( 3 skipped). .. ******
51 2019-10-06 22:25 25 ******
52 2019-10-06 22:30 26 *******
53 2019-10-06 22:35 25 ******
... ..( 33 skipped). .. ******
87 2019-10-07 01:25 25 ******
88 2019-10-07 01:30 26 *******
89 2019-10-07 01:35 27 ********
90 2019-10-07 01:40 26 *******
91 2019-10-07 01:45 26 *******
92 2019-10-07 01:50 26 *******
93 2019-10-07 01:55 25 ******
... ..( 2 skipped). .. ******
96 2019-10-07 02:10 25 ******
97 2019-10-07 02:15 26 *******
... ..( 3 skipped). .. *******
101 2019-10-07 02:35 26 *******
102 2019-10-07 02:40 22 ***
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
#
# date; smartctl --test=long /dev/sdb
Mon Oct 7 02:52:57 CEST 2019
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-6-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately
in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in
off-line mode" successful.
Testing has begun.
Please wait 393 minutes for test to complete.
Test will complete after Mon Oct 7 09:25:57 2019
Use smartctl -X to abort test.
#
# date; smartctl -l selftest /dev/sdb
Mon Oct 7 10:06:04 CEST 2019
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-6-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1802 -
#
Reply to: