problem with etchnhalf on toshiba a305-s6857
I'm trying to install etchnhalf on a toshiba satellite a305-s6857,
using the etchnhalf installer cd. The laptop has a sata hard
drive.
The problem is that once installed the system takes up to 15 min's
to boot, hanging at one or more of the following:
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000d1e334b355a]
usb 1-2: UDSB disconnect, address2
sr 3:0:0:1: Attached scsi generic sg2 type 5
begin: waiting for root file system...
This is when it boots at all. And often it doesn't boot all the
way, but stops with the messages:
Begin: Waiting for root file system...
Done
Check root=bootarg cat /proc/cmdline
or missing modules, device: cat /proc/modules ls /dev
ALERT! /dev/sda3 does not exist. Dropping to a shell! etc.
And a successful boot is always in single-user mode, although the
single-user boot sometimes fails.
Some other hopefully relevant observations:
booting from the installer, I straightaway get the message:
could not find kernel image: /;install/lvmlinuz
(I deal with this by going to the help menu and doing a <CR>.)
When the boot process fails there is always the message:
udevd-event[651]: run_program: '/sbin/modprobe' abnormal exit
the drive works fine when:
the 2.6.18 kernel runs it
the etchnhalf installer itself runs it, whether installing
or in rescue mode
under (sit down, don't gag) vista
it makes no difference whether I run the drive as ahci or in
ide-emulation mode ('compatibility' in the setup menu)
There is no easy way I can include with this post all the output
from dmesg when the system fails to recognize the hard drive, but
below is the output from the boot process when it completes in
single-user mode.
Thanks,
tom arnall
arcata
**********************
00 1 MSFT 1000013)
ACPI: HPET BF6F3000, 0038 (r1 TOSINV TOSINV00 1 MSFT
1000013)
ACPI: MCFG BF6F2000, 003C (r1 TOSINV TOSINV00 1 MSFT
1000013)
ACPI: ASF! BF6F1000, 00A5 (r32 TOSINV TOSINV00 1 MSFT
1000013)
ACPI: SLIC BF6F0000, 0176 (r1 TOSINV TOSINV00 1 MSFT
1000013)
ACPI: BOOT BF6EF000, 0028 (r1 TOSINV TOSINV00 1 MSFT
1000013)
ACPI: SSDT BF6EE000, 04C4 (r1 PmRef CpuPm 3000 INTL
20051117)
ACPI: DMI detected: Toshiba
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap:
c0000000:38000000)
swsusp: Registered nosave memory region: 000000000009f000 -
00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 -
00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 -
0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 1040384
Kernel command line: root=/dev/sda3 ro single
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1995.314 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3092980k/4194304k available (1787k kernel code, 41556k
reserved, 717k data, 248k init, 2218336k highmem)
virtual kernel memory layout:
fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0379000 - 0xc03b7000 ( 248 kB)
.data : 0xc02bedd9 - 0xc0372384 ( 717 kB)
.text : 0xc0100000 - 0xc02bedd9 (1787 kB)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
hpet clockevent registered
Calibrating delay using timer specific routine.. 3994.32 BogoMIPS
(lpj=7988659)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: bfebfbff 20100000 00000000
00000000 0000e39d 00000000 00000001 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940
0000e39d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 Duo CPU T5750 @ 2.00GHz stepping 0d
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.46 BogoMIPS
(lpj=7980930)
CPU: After generic identify, caps: bfebfbff 20100000 00000000
00000000 0000e39d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940
0000e39d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Duo CPU T5750 @ 2.00GHz stepping 0d
Total of 2 processors activated (7984.79 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt
mode
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0,
disabled.
ACPI: Power Resource [FN00] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x164e-0x164f has been reserved
system 00:01: ioport range 0x800-0x80f has been reserved
system 00:01: ioport range 0x400-0x47f has been reserved
system 00:01: ioport range 0x500-0x53f has been reserved
system 00:01: iomem range 0xf8000000-0xfbffffff could not be
reserved
system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be
reserved
system 00:01: iomem range 0xfed14000-0xfed17fff could not be
reserved
system 00:01: iomem range 0xfed18000-0xfed18fff could not be
reserved
system 00:01: iomem range 0xfed19000-0xfed19fff could not be
reserved
system 00:01: iomem range 0xfec00000-0xfec00fff could not be
reserved
system 00:01: iomem range 0xfee00000-0xfee00fff could not be
reserved
system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Bridge: 0000:00:1c.0
IO window: 4000-5fff
MEM window: d5500000-d64fffff
PREFETCH window: d0000000-d10fffff
PCI: Bridge: 0000:00:1c.1
IO window: 3000-3fff
MEM window: d4400000-d54fffff
PREFETCH window: d1100000-d20fffff
PCI: Bridge: 0000:00:1c.4
IO window: 2000-2fff
MEM window: d3400000-d43fffff
PREFETCH window: d2100000-d30fffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: d3300000-d33fffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ
16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ
17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ
16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 4766k freed
Simple Boot Flag at 0x44 set to 0x1
audit: initializing netlink socket (disabled)
audit(1228319653.888:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
Allocate Port Service[0000:00:1c.4:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024
blocksize
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq
1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 248k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Fan [FAN] (on)
ACPI: SSDT BF675C90, 0232 (r1 PmRef Cpu0Ist 3000 INTL
20051117)
ACPI: SSDT BF674610, 05B3 (r1 PmRef Cpu0Cst 3001 INTL
20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT BF675F10, 00C4 (r1 PmRef Cpu1Ist 3000 INTL
20051117)
ACPI: SSDT BF6A7C10, 0083 (r1 PmRef Cpu1Cst 3000 INTL
20051117)
Marking TSC unstable due to: TSC halts in idle.
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
Time: hpet clocksource has been installed.
ACPI: Thermal Zone [THRM] (51 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ
17
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number
1
uhci_hcd 0000:00:1a.0: irq 17, io base 0x000060c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ
18
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number
2
uhci_hcd 0000:00:1a.1: irq 18, io base 0x000060a0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ
19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number
3
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00006080
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ
20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number
4
uhci_hcd 0000:00:1d.1: irq 20, io base 0x00006060
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ
21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number
5
uhci_hcd 0000:00:1d.2: irq 21, io base 0x00006040
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Clocksource tsc unstable (delta = -349637676 ns)
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ
21
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number
6
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 21, io mem 0xd6504c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: can't set config #1, error -71
usb 1-2: USB disconnect, address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ
19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number
7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xd6504800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ
20
ahci 0000:00:1f.2: nr_ports (3) and implemented port map (0x3)
don't match, using nr_ports
ahci 0000:00:1f.2: forcing PORTS_IMPL to 0x7
usb 6-2: new high speed USB device using ehci_hcd and address 2
usb 6-2: configuration #1 chosen from 1 choice
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl
SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp
pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xd6504000 port 0xd6504100 irq
220
ata2: SATA max UDMA/133 abar m2048@0xd6504000 port 0xd6504180 irq
220
ata3: SATA max UDMA/133 abar m2048@0xd6504000 port 0xd6504200 irq
220
usb 4-1: new full speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: TOSHIBA MK3252GSX, LV010M, max UDMA/100
ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 0)
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK3252GS LV01 PQ:
0 ANSI: 5
ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI slot
0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ
20
ICH8M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x60e0-0x60e7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x60e8-0x60ef, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
hda: HL-DT-ST DVDRAM GSA-T40F, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ACPI: PCI Interrupt 0000:06:06.0[B] -> GSI 17 (level, low) -> IRQ
16
PCI: Setting latency timer of device 0000:06:06.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[d3300000-d33007ff] Max Packet=[2048] IR/IT contexts=[4/4]
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
PCI: 0000:02:00.0 has unsupported PM cap regs version (7)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ
17
PCI: Setting latency timer of device 0000:02:00.0 to 64
BUG: unable to handle kernel NULL pointer dereference at virtual
address 00000118
printing eip: c023f550 *pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in: generic sd_mod usb_storage ahci ohci1394 libata
ieee1394 scsi_mod piix ide_core r8169 ehci_hcd uhci_hcd usbcore
thermal processor fan
Pid: 654, comm: modprobe Not tainted (2.6.24-etchnhalf.1-686 #1)
EIP: 0060:[<c023f550>] EFLAGS: 00010202 CPU: 1
EIP is at dev_driver_string+0x0/0x29
EAX: 0000004c EBX: 00000000 ECX: f885e000 EDX: f88635c4
ESI: 000000e4 EDI: 37a00000 EBP: f74f33e0 ESP: f75a7d80
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process modprobe (pid: 654, ti=f75a6000 task=f74a2c30
task.ti=f75a6000)
Stack: f8861f3d f8863913 f8863861 f8863867 c01df3f5 f76097c0
f75a7de0 c0352aa4
c018886b f7c1dc00 c01b14f3 c30c0b68 f7c1dc00 f7d40c00
c0188969 f7d4b560
f8863128 f74f3000 f885e000 00000000 f885e040 c01b17fa
f7d4b560 f7876d4c
Call Trace:
[<f8861f3d>] rtl8169_init_one+0x36a/0xa26 [r8169]
[<c01df3f5>] ida_get_new_above+0xe1/0x162
[<c018886b>] find_inode+0x1b/0x56
[<c01b14f3>] sysfs_ilookup_test+0x0/0xd
[<c0188969>] ifind+0x33/0x7b
[<c01b17fa>] sysfs_add_one+0xaf/0xb8
[<c01b1853>] sysfs_addrm_start+0x50/0x81
[<c01b2397>] sysfs_create_link+0xb8/0xfd
[<c011d4e2>] __wake_up_common+0x32/0x5c
[<c01dfaea>] kobject_get+0xf/0x13
[<c01ebaa3>] pci_device_probe+0x36/0x57
[<c0241a58>] driver_probe_device+0xde/0x15c
[<c02bbd79>] klist_next+0x4b/0x6c
[<c0241b68>] __driver_attach+0x0/0x79
[<c0241bae>] __driver_attach+0x46/0x79
[<c024102f>] bus_for_each_dev+0x33/0x55
[<c02418bf>] driver_attach+0x16/0x18
[<c0241b68>] __driver_attach+0x0/0x79
[<c0241315>] bus_add_driver+0x6d/0x197
[<c01ebbe0>] __pci_register_driver+0x48/0x74
[<c01437a7>] sys_init_module+0x15e3/0x16fb
[<c0164162>] vma_prio_tree_insert+0x17/0x2a
[<c01569bb>] disable_irq+0x0/0x25
[<c0103ede>] syscall_call+0x7/0xb
=======================
Code: 85 c0 79 23 b9 fa ab 30 c0 31 d2 b8 fe 50 32 c0 89 1c 24 c7
44 24 04 88 7d 3f c0 e8 a6 55 ee ff eb 05 b8 ed ff ff ff 5a 59 5b
c3 <8b> 90 cc 00 00 00 85 d2 75 0a 8b 90 c8 00 00 00 85 d2 74 03
8b
EIP: [<c023f550>] dev_driver_string+0x0/0x29 SS:ESP 0068:f75a7d80
---[ end trace 4d33275af986e8fb ]---
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080d1e334b355a]
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access SanDisk ImageMate II 1.30 PQ:
0 ANSI: 2
sd 3:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI removable disk
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
input: PC Speaker as /class/input/input1
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ACPI: Power Button (CM) [PWRB]
input: Lid Switch as /class/input/input4
iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux,
1.1.17ks
iwl4965: Copyright(c) 2003-2007 Intel Corporation
ACPI: Lid Switch [LID]
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Video Bus as /class/input/input5
ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1e0b1, caps:
0xd04711/0xa00000
synaptics: Toshiba Satellite A305 detected, limiting rate to
40pps.
input: SynPS/2 Synaptics TouchPad as /class/input/input6
Adding 2658716k swap on /dev/sda5. Priority:-1 extents:1
across:2658716k
EXT3 FS on sda3, internal journal
loop: module loaded
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised:
dm-devel@redhat.com
usb 4-1: USB disconnect, address 2
usb 4-1: new full speed USB device using uhci_hcd and address 3
usb 4-1: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access SanDisk ImageMate II 1.30 PQ:
0 ANSI: 2
sd 4:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI removable disk
usb 4-1: USB disconnect, address 3
usb 7-3: new high speed USB device using ehci_hcd and address 4
usb 7-3: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 5:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
scsi 5:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
sd 5:0:0:0: [sdc] 990865 512-byte hardware sectors (507 MB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 5:0:0:0: [sdc] Assuming drive cache: write through
sd 5:0:0:0: [sdc] 990865 512-byte hardware sectors (507 MB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 5:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 5:0:0:0: [sdc] Attached SCSI removable disk
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
sr 5:0:0:1: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 5:0:0:0: Attached scsi generic sg1 type 0
sr 5:0:0:1: Attached scsi generic sg2 type 5
usb 4-2: new full speed USB device using uhci_hcd and address 4
usb 4-2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 6:0:0:0: Direct-Access SanDisk ImageMate II 1.30 PQ:
0 ANSI: 2
sd 6:0:0:0: [sdd] 250880 512-byte hardware sectors (128 MB)
sd 6:0:0:0: [sdd] Write Protect is off
sd 6:0:0:0: [sdd] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sdd] Assuming drive cache: write through
sd 6:0:0:0: [sdd] 250880 512-byte hardware sectors (128 MB)
sd 6:0:0:0: [sdd] Write Protect is off
sd 6:0:0:0: [sdd] Mode Sense: 0b 00 00 08
sd 6:0:0:0: [sdd] Assuming drive cache: write through
sdd: sdd1
sd 6:0:0:0: [sdd] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg3 type 0
scsi 4:0:0:0: rejecting I/O to dead device
usb 4-2: USB disconnect, address 4
usb 7-3: USB disconnect, address 4
usb 7-3: new high speed USB device using ehci_hcd and address 6
usb 7-3: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
scsi 7:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
sd 7:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sd 7:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 7:0:0:0: [sdb] Attached SCSI removable disk
sd 7:0:0:0: Attached scsi generic sg1 type 0
sr0: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
sr 7:0:0:1: Attached scsi CD-ROM sr0
sr 7:0:0:1: Attached scsi generic sg2 type 5
usb 7-3: USB disconnect, address 6
usb 7-3: new high speed USB device using ehci_hcd and address 7
usb 7-3: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 8:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
scsi 8:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.21 PQ:
0 ANSI: 2
sd 8:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 8:0:0:0: [sdb] Write Protect is off
sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 8:0:0:0: [sdb] Assuming drive cache: write through
sd 8:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 8:0:0:0: [sdb] Write Protect is off
sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 8:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 8:0:0:0: [sdb] Attached SCSI removable disk
sd 8:0:0:0: Attached scsi generic sg1 type 0
sr0: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
sr 8:0:0:1: Attached scsi CD-ROM sr0
sr 8:0:0:1: Attached scsi generic sg2 type 5
usb 7-3: USB disconnect, address 7
usb 4-1: new full speed USB device using uhci_hcd and address 5
usb 4-1: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 9:0:0:0: Direct-Access SanDisk ImageMate II 1.30 PQ:
0 ANSI: 2
sd 9:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 9:0:0:0: [sdb] Write Protect is off
sd 9:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 9:0:0:0: [sdb] Assuming drive cache: write through
sd 9:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 9:0:0:0: [sdb] Write Protect is off
sd 9:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 9:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 9:0:0:0: [sdb] Attached SCSI removable disk
sd 9:0:0:0: Attached scsi generic sg1 type 0
usb 4-1: USB disconnect, address 5
usb 4-2: new full speed USB device using uhci_hcd and address 6
usb 4-2: configuration #1 chosen from 1 choice
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 10:0:0:0: Direct-Access SanDisk ImageMate II 1.30
PQ: 0 ANSI: 2
sd 10:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 10:0:0:0: [sdb] Write Protect is off
sd 10:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 10:0:0:0: [sdb] Assuming drive cache: write through
sd 10:0:0:0: [sdb] 250880 512-byte hardware sectors (128 MB)
sd 10:0:0:0: [sdb] Write Protect is off
sd 10:0:0:0: [sdb] Mode Sense: 0b 00 00 08
sd 10:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 10:0:0:0: [sdb] Attached SCSI removable disk
sd 10:0:0:0: Attached scsi generic sg1 type 0
usb 4-2: USB disconnect, address 6
usb 7-3: new high speed USB device using ehci_hcd and address 10
usb 7-3: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 11:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 3.21
PQ: 0 ANSI: 2
scsi 11:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 3.21
PQ: 0 ANSI: 2
sd 11:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 11:0:0:0: [sdb] Write Protect is off
sd 11:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 11:0:0:0: [sdb] Assuming drive cache: write through
sd 11:0:0:0: [sdb] 990865 512-byte hardware sectors (507 MB)
sd 11:0:0:0: [sdb] Write Protect is off
sd 11:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 11:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 11:0:0:0: [sdb] Attached SCSI removable disk
sd 11:0:0:0: Attached scsi generic sg1 type 0
sr0: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
sr 11:0:0:1: Attached scsi CD-ROM sr0
sr 11:0:0:1: Attached scsi generic sg2 type 5
Reply to: