Re: monitor PC2000 F17 69T technical informations?
Sorry to hear that read-edid did not work for you.
Perhaps PC2000 is not the manufacturer. I seem to remember a monitor
certification called PC2000. (Googling....yes, here it is:
<http://www.panasonic.com.au/products/faqs/details.cfm?detailsID=175&objectID=146&categoryID=0&productID=0&lListIDs=178,197,179,198,170,171,167,166,163,173,160,159,158,168,164,161,169,162,174,172,165,190,185,193,191,199,194,187,192,186,177,188,175,195,183,182,184,181,176,196,189,200,180>).
Other than that, I found:
<http://www.si87.com/MonitorSolutions/kaga/fi769mt.html>,
<http://www.si87.com/MonitorSolutions/pc2000/f1785t.html>,
<http://www.forum.linux-sevenler.org/index.php/topic,866.0.html>,
Which may be close enough.
Also, if it is a 17" monitor (which I suspect it is), then you can't go
wrong with the settings:
Horz 35-60
Vert 55-90
These are VERY conservitive settings; you could probably go as high as
30-65,50-100 without worry.
Good Luck,
Kevin
On Sun, 2005-08-21 at 19:10 +0200, Csanyi Pal wrote:
> On Sun, Aug 21, 2005 at 06:24:34PM +0200, Alexander Schmehl wrote:
> > * Csanyi Pal <csanyipal@sks.co.yu> [050821 17:18]:
> > > I have the monitor PC2000 F17 69T.
> > > It was given to me yesterday, but without the manual.
> > > I need the technical informations bellow to set up my X Window:
> > [..]
> > > Has anybody these informations? If so, please tell me! Thanks!
> >
> > Take a look at read-edid [1], which might find that information for you.
>
> sudo get-edid
> get-edid: get-edid version 1.4.1
>
> Performing real mode VBE call
> Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
> Function supported
> Call successful
>
> VBE version 300
> VBE string at 0x11110 "Brookdale-G Graphics Chip Accelerated VGA BIOS"
>
> VBE/DDC service about to be called
> Report DDC capabilities
>
> Performing real mode VBE call
> Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
> Function supported
> Call successful
>
> Monitor and video card combination does not support DDC1 transfers
> Monitor and video card combination does not support DDC2 transfers
> 0 seconds per 128 byte EDID block transfer
> Screen is not blanked during DDC transfer
>
> Reading next EDID block
>
> VBE/DDC service about to be called
> Read EDID
>
> Performing real mode VBE call
> Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
> Function supported
> Call failed
>
> The EDID data should not be trusted as the VBE call failed
> Error: output block unchanged
>
> Thank you Alexander, but as You see abowe, I can't get the wanted
> informations.
>
> --
> Regards,
> Paul
> Debian Junior Project, DebianEdu, Moodle -> :-) :-) :-) :-) :-) :-) :-)
> http://www.ektf.hu/~Csanyi.Pal (Up to now, it is in Hungarian only.)
>
>
Reply to: