Re: for the love of GOD! SATA DVD Burner
roach wrote:
SUPRISE!
See somebody did answer. Now peel yourself off the floor and lets continue...
I doubt very much that this is a problem with linux and relates more to your
SATA controller chipset. Most chipsets assume that you'd only connect a
harddrive and therefore only support harddrives.
What is your SATA controller chipset? If you've got more than one kind have
you tried on the other?
BTW, I know this to be true because I wanted to buy a plextor CD drive and
found out it was incompatible with my motherboards SATA chipsets :-(
Amazing! My first response to this question out of all the times I've
even brought it up! Thank you!
lspci shows it as this;
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02)
lsmod shows it loaded;
libata 48068 2 sata_nv,sata_sil
The board is an nforce2 Asus A7N8X-E Deluxe
dmesg
libata version 1.10 loaded.
sata_sil version 0.8
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 18 (level, high) -> IRQ 217
ata1: SATA max UDMA/100 cmd 0xF8AA4080 ctl 0xF8AA408A bmdma 0xF8AA4000
irq 217
ata2: SATA max UDMA/100 cmd 0xF8AA40C0 ctl 0xF8AA40CA bmdma 0xF8AA4008
irq 217
ieee1394: Host added: ID:BUS[1-00:1023] GUID[00023c01510ef10c]
ieee1394: Node added: ID:BUS[1-01:1023] GUID[000a2700141f1a42]
ieee1394: The root node is not cycle master capable; selecting a new
root node and resetting...
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000b04941]
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:001f
ata1: dev 0 ATAPI, max UDMA/66
ata1: dev 0 configured for UDMA/66
scsi0 : sata_sil
ieee1394: Node changed: 1-01:1023 -> 1-00:1023
ieee1394: Node changed: 1-00:1023 -> 1-01:1023
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Then there is this; (these should be my 3 ports on my flash card
reader.... I think)
cat /proc/scsi/scsi
Attached devices:
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: STORAGE DEVICE Rev: 0228
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vendor: Generic Model: STORAGE DEVICE Rev: 0228
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 02
Vendor: Generic Model: STORAGE DEVICE Rev: 0228
Type: Direct-Access ANSI SCSI revision: 02
I have 2 DVD drives, the burner and the DVD rom on my IDE controller. I
just can't seem to find the SATA DVD burner which I believe is due to it
not being there. I'm kind of lost but I *think* it is just ignoring that
its there. By the looks of it to me, it looks like it should be
detecting just fine, giving me my sd* that I can use with it. But None
of that seems to be happening. And I'm sort of lost.
Thanks Again,
-Mike
Reply to: