BP6 + System hangs
Not strictly a Debian question, more a general hardware issue, i know.. but i gotta start somewhere.
I have a BP6 with 2xCeleron 433. And it seems that justabout any heavy disk activity towards the disks on the HPT366 controller freezez the system up completely to the point of cold boot. Has anyone any thoughts on this?
Below is some output leading up to the lockup.
cookiemonster:~# dmesg
Linux version 2.4.18-686-smp (herbert@gondolin) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Sun Apr 14 12:07:19 EST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
found SMP MP-table at 000f5ae0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: auto BOOT_IMAGE=Linux ro root=803
Initializing CPU#0
Detected 434.320 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 865.07 BogoMIPS
Memory: 253132k/262144k available (900k kernel code, 8628k reserved, 250k data, 216k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU0: Intel Celeron (Mendocino) stepping 05
per-CPU timeslice cutoff: 365.86 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 868.35 BogoMIPS
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU1: Intel Celeron (Mendocino) stepping 05
Total of 2 processors activated (1733.42 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-12, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 21.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
10 003 03 1 1 0 1 0 1 1 89
11 003 03 1 1 0 1 0 1 1 91
12 003 03 1 1 0 1 0 1 1 99
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 434.3273 MHz.
..... host bus clock speed is 66.8193 MHz.
cpu: 0, clocks: 668193, slice: 222731
CPU0<T0:668192,T1:445456,D:5,S:222731,C:668193>
cpu: 1, clocks: 668193, slice: 222731
CPU1<T0:668192,T1:222720,D:10,S:222731,C:668193>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I11,P0) -> 18
PCI->APIC IRQ transform: (B0,I13,P0) -> 17
PCI->APIC IRQ transform: (B0,I15,P0) -> 16
PCI->APIC IRQ transform: (B0,I17,P0) -> 19
PCI->APIC IRQ transform: (B0,I19,P0) -> 18
PCI->APIC IRQ transform: (B0,I19,P1) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 2712 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 2712k freed
VFS: Mounted root (cramfs filesystem).
Journalled Block Device driver loaded
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec 2940A Ultra SCSI adapter>
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
Vendor: SONY Model: SDT-9000 Rev: 0400
Type: Sequential-Access ANSI SCSI revision: 02
(scsi0:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: IBM OEM Model: DFHSS2W Rev: 4141
Type: Direct-Access ANSI SCSI revision: 02
(scsi1:A:0): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: IBM Model: DDYS-T09170N Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
(scsi1:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
scsi1:A:0:0: Tagged Queuing enabled. Depth 8
scsi1:A:1:0: Tagged Queuing enabled. Depth 8
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
SCSI device sda: 4404489 512-byte hdwr sectors (2255 MB)
Partition check:
/dev/scsi/host1/bus0/target0/lun0: p1 p2 p3
SCSI device sdb: 17916240 512-byte hdwr sectors (9173 MB)
/dev/scsi/host1/bus0/target1/lun0: p1
cramfs: wrong magic
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sd(8,3): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 174131
ext3_orphan_cleanup: deleting unreferenced inode 142034
ext3_orphan_cleanup: deleting unreferenced inode 65316
ext3_orphan_cleanup: deleting unreferenced inode 110423
EXT3-fs: sd(8,3): 4 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
change_root: old root has d_count=2
Freeing unused kernel memory: 216k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 128516k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,3), internal journal
Real Time Clock Driver v1.10e
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: Intel Corp. 82557 [Ethernet Pro 100], 00:90:27:D1:65:32, IRQ 17.
Board assembly 721383-007, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
8139too Fast Ethernet driver 0.9.24
eth1: RealTek RTL8139 Fast Ethernet at 0xd089a000, 00:c1:26:0a:29:ca, IRQ 19
eth1: Identified 8139 chip type 'RTL-8139C'
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,17), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
HPT366: onboard version of chipset, pin1=1 pin2=2
HPT366: IDE controller on PCI bus 00 dev 98
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:DMA
HPT366: IDE controller on PCI bus 00 dev 99
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide3: BM-DMA at 0xe800-0xe807, BIOS settings: hdg:DMA, hdh:DMA
hda: IC35L080AVVA07-0, ATA DISK drive
hde: ST38641A, ATA DISK drive
hdf: IBM-DTLA-307075, ATA DISK drive
hdg: IC35L040AVER07-0, ATA DISK drive
hdh: FUJITSU MPG3409AT E, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xd400-0xd407,0xd802 on irq 18
ide3 at 0xe000-0xe007,0xe402 on irq 18
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=159560/16/63
hde: 16809660 sectors (8607 MB) w/128KiB Cache, CHS=16676/16/63, UDMA(33)
hdf: 150136560 sectors (76870 MB) w/1916KiB Cache, CHS=148945/16/63, UDMA(44)
hdg: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=79780/16/63, UDMA(44)
hdh: 80063424 sectors (40992 MB) w/2048KiB Cache, CHS=79428/16/63, UDMA(66)
/dev/ide/host0/bus0/target0/lun0: p1
/dev/ide/host2/bus0/target0/lun0: [PTBL] [1046/255/63] p1
/dev/ide/host2/bus0/target1/lun0: [PTBL] [9345/255/63] p1
/dev/ide/host3/bus0/target0/lun0: p1
/dev/ide/host3/bus0/target1/lun0: p1
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,65), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide3(34,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
cookiemonster:~# hdparm /dev/hdg
/dev/hdg:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 79780/16/63, sectors = 80418240, start = 0
busstate = 1 (on)
cookiemonster:~# hdparm /dev/hda
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 159560/16/63, sectors = 160836480, start = 0
busstate = 1 (on)
cookiemonster:~# hdparm -Tt /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.49 seconds = 85.91 MB/sec
Timing buffered disk reads: 64 MB in 18.29 seconds = 3.50 MB/sec
cookiemonster:~# hdparm -Tt /dev/hdh
/dev/hdh:
Timing buffer-cache reads: 128 MB in 1.44 seconds = 88.89 MB/sec
Timing buffered disk reads:
--
To UNSUBSCRIBE, email to debian-user-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: