Re: lilo stuff -- [ soundblaster sb 16 ]
>
hi
the lilo and the old lilofile (which worked pretty good) are attachements now.
maybe i forgetz an important scsi thing to set on in the kernel?
or maybe it was the wrong scsi driver, i dont know.
NCR 53c875 (rev 38) is my scsi chip on a pci card.
thank you for helping
markus
> hi ya markus...
>
> easiest way to get around the lilo problem...
> - boot your server with a different media ( floppy or cdrom )
> - make a boot floppy
> # dd if=/vmlinuz of=/dev/fd0 bs=1024 )
> # rdev /dev/fd0 /dev/sda1
> ( if your /vmlinuz is on /dev/sda1 )
> if it boots...good
>
> - probably wont work...since you're booting off sda1
> ( you might need to get initrd on it too )
>
> - make sure your kernel ( /vmlinuz) supports your scsi disk
> ( you'll get kernel panic if it cant find / on your system
> ( in which case you're 1/2 way there
>
> - otherwise... dig into your "large-disk howto"
> - see if the BIOS recognizes your disk on bios boot
>
> - see if you have to set the "large disk" jumper for your hardisk
> - probably need a jumper on your disk
>
> - what is the rest of your lilo.conf file???
> - do you have initrd=... ??? ( you need it for booting from sda1 )
> - do you have lba32 ???
> - do you have linear ??
> - add each option and rerun lilo and see if it helps booting
>
> innie...meanie...my knee moe.... pick one and start playing...
>
> have fun
> alvin
>
> On Thu, 26 Jul 2001, Markus Hansen wrote:
>
> > Hi i tried to use a manual configured kernel, but when i tried to start it lilo
> > wasnt working
> > it just said
> > LI
> > LI
> > LI
> > etc... so my problem is to write a right lilo, right?
> > now i am booting with disk and this is slooooow
> > but anyway, i dont know what i have to do, lilo already say things line
> > image=/vmlinuz
> > label=linux
> > read-only
> > so what is wrong with the lilo, i guess it is a difficult question, because i
> > havent written what i applied to in the kernel and what not.
> > i send the data with me as attatchement
> > thank you for helping me.
> > ps i am booting from a scsi device called sda1
> > markus
#image=/boot/zImage-2.2.17
# label=Linux
# read-only
# append="hdc=ide-scsi"
# options ide-cd ignore=hdc
# alias scd0 sr_mod
# pre-install sg modprobe ide-scsi
# pre-install sr_mod modprobe ide-scsi
# pre-install ide-scsi modprobe ide-cd
# cd /dev && rm cdrom && ln -s scd0 cdrom
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/sda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/sda1
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
image=/boot/zImage-2.2.17
label=Linux
read-only
append="hdc=ide-scsi"
options ide-cd ignore=hdc
alias scd0 sr_mod
pre-install sg modprobe ide-scsi
pre-install sr_mod modprobe ide-scsi
pre-install ide-scsi modprobe ide-cd
cd /dev && rm cdrom && ln -s scd0 cdrom
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/sda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/sda1
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
Reply to: