Re: fstab entry for cd-rw device?
Thanks for all of your replys guys. I still have been unable to get my cd-rw
working under Linux. I think that the ide-scsi module is conflicting with another
scsi module at boot-time. (*see dmesg output at the end of this message)
Why this module is loading I have no idea, I do not have any scsi hardware and do
not load any scsi modules at boot time besides the scsi emulation module
(ide-scsi).
I can mount the device as /dev/hdc but cannot mount it as /dev/cdrom or even
/dev/scd0. The error messages I receive are:
mount: the kernel does not recognize /dev/scd0 as a block device
(maybe `insmod driver'?)
or
mount: the kernel does not recognize /dev/cdrom as a block device
(maybe `insmod driver'?)
This puzzles me too since ide-scsi is loaded according to lsmod:
sg 15320 0 (autoclean) (unused)
ip_masq_raudio 2936 0 (unused)
ip_masq_ftp 2456 0 (unused)
af_packet 6040 0 (autoclean)
serial 19564 0 (autoclean)
ide-scsi 7080 0
autofs 9088 0 (unused)
nvram 3460 0 (unused)
es1371 25344 1
soundcore 2628 4 [es1371]
ne2k-pci 4072 1
8390 6036 0 [ne2k-pci]
3c59x 18656 1
unix 10212 81 (autoclean)
cdrecord -scanbus does not reveal my cd-rw as well. I'm I missing some
configurations for the ide-scsi module in /etc/modules.conf ? Do I need to
recompile the kernel and exclude native scsi support, or can I simply turn it off
by adding some syntax to /etc/modules.conf?
I'm running out of ideas here and would apreciate all the help you can give me.
Thanks
Stef
Linux version 2.2.17 (herbert@arnor) (gcc version 2.95.2 20000313 (Debian
GNU/Linux)) #1 Sun Jun 25 09:24:41 EST 2000
Detected 553884 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1104.28 BogoMIPS
Memory: 126984k/131008k available (1732k kernel code, 416k reserved, 1736k data,
140k init)
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: L1 I Cache: 64K L1 D Cache: 64K
CPU: L2 Cache: 512K
CPU: AMD Athlon(tm) Processor stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfd9e1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:00
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
apm: disabled on user request.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
loop: registered device at major 7
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 92041U4, ATA DISK drive
hdc: ZIPCD 4x650, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 92041U4, 19541MB w/512kB Cache, CHS=2491/255/63
hdc: ATAPI 24X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0
Failed initialization of WD-7000 SCSI card!
IBM MCA SCSI: No Microchannel-bus support present -> Aborting.
megaraid: v107 (December 22, 1999)
aec671x_detect:
3w-xxxx: tw_findcards(): No cards found.
scsi : 0 hosts.
scsi : detected total.
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 >
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 140k freed
NET4: Unix domain sockets 1.0 for Linux NET4.0.
Adding Swap: 96352k swap-space (priority -1)
3c59x.c:v0.99H 12Jun00 Donald Becker and others
http://www.scyld.com/network/vortex.html
eth0: 3Com 3c900 Cyclone 10Mbps TPO at 0xd400, 00:50:da:7a:f7:c5, IRQ 10
8K byte-wide RAM 5:3 Rx:Tx split, 10baseT interface.
Media override to transceiver type 0 (10baseT).
Enabling bus-master transmits and whole-frame receives.
ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xd000, IRQ 9.
eth1: RealTek RTL-8029 found at 0xd000, IRQ 9, 00:60:67:3A:EE:7C.
es1371: version v0.22 time 09:53:39 Jun 25 2000
es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02
es1371: found es1371 rev 2 at io 0xcc00 irq 5
es1371: features: joystick 0x0
es1371: codec vendor v (0x838476) revision 9 (0x09)
es1371: codec features 18bit DAC 18bit ADC
es1371: stereo enhancement: SigmaTel SS3D
Non-volatile memory driver v1.0
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
Serial driver version 4.27 with no serial options enabled
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
Reply to: