RE: SCSI bus reset when burning
I have this same type of problem when I try to use SCSI tape backup.
I get simular error messages and the machine's load goes pretty high and
sometimes needs to be rebooted.
I have had no luck getting the tape backup to work.
this is the error i get:
--
May 3 14:23:23 taz kernel: SCSI host 0 abort (pid 228089503) timed out -
resetting
May 3 14:23:23 taz kernel: SCSI bus is being reset for host 0 channel 0.
--
We both have Adaptech controllers.......
--
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.10/3.2.4
<Adaptec AIC-7880 Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.10/3.2.4
<Adaptec AIC-7860 Ultra SCSI host adapter>
scsi2 : AMI MegaRAID U.75 254 commands 16 targs 2 chans
scsi : 3 hosts.
--
> -----Original Message-----
> From: Rob Rati [mailto:ratirh@cs.purdue.edu]
> Sent: Tuesday, May 23, 2000 4:15 AM
> To: criggie@ihug.co.nz
> Cc: 'debian-user@lists.debian.org'
> Subject: Re: SCSI bus reset when burning
>
>
> Here's what dmesg says about my scsi chain. I have 2 hds, 1 dvd drive,
> and a burner on it. The burner works great when I mount it as a cd-rom
> drive. No apparant problems at all. The SCSI card is on ID 7, but the
> ID of the device shouldn't matter should it? As long as it's not the
> same ID as another device on the chain. None of the other devices have
> any problems, just the burner causes the SCSI bus to reset.
>
> (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 0/10/0
> (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
> (scsi0) Downloading sequencer code... 423 instructions downloaded
> scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
> <Adaptec AHA-294X Ultra SCSI host adapter>
> scsi : 1 host.
> (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> Vendor: YAMAHA Model: CRW6416S Rev: 1.0c
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> (scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 8.
> Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
> (scsi0:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 8.
> Vendor: COMPAQ Model: 3391SS Rev: C70E
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 3, lun 0
> (scsi0:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 8.
> Vendor: COMPAQ Model: 3391SS Rev: C424
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
> scsi : detected 2 SCSI cdroms 2 SCSI disks total.
> sr0: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.07
> sr1: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 17773500 [8678 MB]
> [8.7 GB]
> SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17773500 [8678 MB]
> [8.7 GB]
>
> Rob
>
> "C. Falconer" wrote:
> >
> > Does your SCSI drive work if you try to mount it like a CDROM ?
> Do you have any other SCSI devices (hard drive/another CD etc)
> >
> > Have you considered setting the scsi ID to something like 2
> through 5? the card is often ID6.
> >
> > Can you please post the dmesg lines from boot that show what
> scsi devices are detected?
> >
> > ----------
> > From: Rob Rati[SMTP:ratirh@cs.purdue.edu]
> > Reply To: ratirh@cs.purdue.edu
> > Sent: Tuesday, 23 May 2000 5:23 PM
> > To: debian-user@lists.debian.org
> > Subject: SCSI bus reset when burning
> >
> > My scsi bus appears to want to reset everytime I try to burn a CD. My
> > dmesg log gets errors like this:
> >
> > scsi : aborting command due to timeout : pid 232511, scsi0, channel 0,
> > id 0, lun 0 0x2a 00 00 00 2f e0 00 00 10 00
> > (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> > scsi : aborting command due to timeout : pid 236020, scsi0, channel 0,
> > id 0, lun 0 0x2a 00 00 00 1f 30 00 00 10 00
> > (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> > scsi : aborting command due to timeout : pid 237829, scsi0, channel 0,
> > id 0, lun 0 0x2a 00 00 00 08 40 00 00 10 00
> > (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> >
> > Scsi id 0 is my burner, so it appears to be having some kind of
> > problem. Does anyone know how to solve this or why the scsi bus wants
> > to reset? Any help would be appreciated since I can't burn CDs until
> > this is figured out. TIA.
> >
> > Rob
> > --
> > ratirh@lore.cs.purdue.edu 1999-00 |
> > Aka Khyron the Backstabber | L I NN N U U X X O
> > ICQ# 2325055 | L I N NN U U X
> > | LLL I N N UUU X X O
> > "Shackles cannot keep me bound | Those who can, do.
> > forever. I'm outta here." |
> >
> > --
> > Unsubscribe? mail -s unsubscribe
> debian-user-request@lists.debian.org < /dev/null
> >
> > --
> > Unsubscribe? mail -s unsubscribe
> debian-user-request@lists.debian.org < /dev/null
>
> --
> ratirh@lore.cs.purdue.edu 1999-00 |
> Aka Khyron the Backstabber | L I NN N U U X X O
> ICQ# 2325055 | L I N NN U U X
> | LLL I N N UUU X X O
> "Shackles cannot keep me bound | Those who can, do.
> forever. I'm outta here." |
>
Reply to: