Re: SCSI bus reset when burning
Here's what dmesg says about my scsi chain. I have 2 hds, 1 dvd drive,
and a burner on it. The burner works great when I mount it as a cd-rom
drive. No apparant problems at all. The SCSI card is on ID 7, but the
ID of the device shouldn't matter should it? As long as it's not the
same ID as another device on the chain. None of the other devices have
any problems, just the burner causes the SCSI bus to reset.
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 0/10/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 423 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: YAMAHA Model: CRW6416S Rev: 1.0c
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
(scsi0:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: COMPAQ Model: 3391SS Rev: C70E
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 8.
Vendor: COMPAQ Model: 3391SS Rev: C424
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
scsi : detected 2 SCSI cdroms 2 SCSI disks total.
sr0: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.07
sr1: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17773500 [8678 MB]
[8.7 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17773500 [8678 MB]
[8.7 GB]
Rob
"C. Falconer" wrote:
>
> Does your SCSI drive work if you try to mount it like a CDROM ? Do you have any other SCSI devices (hard drive/another CD etc)
>
> Have you considered setting the scsi ID to something like 2 through 5? the card is often ID6.
>
> Can you please post the dmesg lines from boot that show what scsi devices are detected?
>
> ----------
> From: Rob Rati[SMTP:ratirh@cs.purdue.edu]
> Reply To: ratirh@cs.purdue.edu
> Sent: Tuesday, 23 May 2000 5:23 PM
> To: debian-user@lists.debian.org
> Subject: SCSI bus reset when burning
>
> My scsi bus appears to want to reset everytime I try to burn a CD. My
> dmesg log gets errors like this:
>
> scsi : aborting command due to timeout : pid 232511, scsi0, channel 0,
> id 0, lun 0 0x2a 00 00 00 2f e0 00 00 10 00
> (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> scsi : aborting command due to timeout : pid 236020, scsi0, channel 0,
> id 0, lun 0 0x2a 00 00 00 1f 30 00 00 10 00
> (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> scsi : aborting command due to timeout : pid 237829, scsi0, channel 0,
> id 0, lun 0 0x2a 00 00 00 08 40 00 00 10 00
> (scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
>
> Scsi id 0 is my burner, so it appears to be having some kind of
> problem. Does anyone know how to solve this or why the scsi bus wants
> to reset? Any help would be appreciated since I can't burn CDs until
> this is figured out. TIA.
>
> Rob
> --
> ratirh@lore.cs.purdue.edu 1999-00 |
> Aka Khyron the Backstabber | L I NN N U U X X O
> ICQ# 2325055 | L I N NN U U X
> | LLL I N N UUU X X O
> "Shackles cannot keep me bound | Those who can, do.
> forever. I'm outta here." |
>
> --
> Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org < /dev/null
>
> --
> Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org < /dev/null
--
ratirh@lore.cs.purdue.edu 1999-00 |
Aka Khyron the Backstabber | L I NN N U U X X O
ICQ# 2325055 | L I N NN U U X
| LLL I N N UUU X X O
"Shackles cannot keep me bound | Those who can, do.
forever. I'm outta here." |
Reply to: