RE: Jaz 1Gb on hamm dist
Thank You for the help,
I tried /dev/sdc4 without success and then sequentially tried /dev/sdc1 and
/dev/sdc2, no luck there either.
Then, on a wild hunch I tried mounting /dev/sdc without specifying a number
and it worked! I have no idea why it worked, but your suggestions did put
me on the right path so I'm not going to look this gift horse too closely in
the mouth.
Again, thank you.
- BOHICA
-----Original Message-----
From: Brandon Mitchell [mailto:bhmit1@mail.wm.edu]
Sent: Sunday, December 06, 1998 21:58
To: BOHICA
Cc: debian-user@lists.debian.org
Subject: RE: Jaz 1Gb on hamm dist
I wrote:
> Can you send me (and the list too) the output of "dmesg" and "fdisk -l"
> with the cartridge in the drive? This will help verify you are using the
> correct device.
On Sun, 6 Dec 1998, BOHICA wrote:
> ------------ dmesg -------------
>
> Vendor: iomega Model: jaz 1GB Rev: H.72
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi removable disk sdc at scsi1, channel 0, id 5, lun 0
Ok, sdc is correct.
> ----------- fdisk -l ------------
>
> Disk /dev/sdc: 64 heads, 32 sectors, 1021 cylinders
> Units = cylinders of 2048 * 512 bytes
>
> Device Boot Begin Start End Blocks Id System
> /dev/sdc1 ? 937318 937477 1203315272218546+ 20 Unknown
> Partition 1 has different physical/logical beginnings (non-Linux?):
> phys=(356, 97, 46) logical=(937476, 3, 15)
> Partition 1 has different physical/logical endings:
> phys=(357, 116, 40) logical=(1203314, 30, 19)
> Partition 1 does not end on cylinder boundary:
> phys=(357, 116, 40) should be (357, 63, 32)
> /dev/sdc2 ? 648482 649505 912677269488144 6b Unknown
> Partition 2 has different physical/logical beginnings (non-Linux?):
> phys=(288, 110, 57) logical=(649504, 0, 11)
> Partition 2 has different physical/logical endings:
> phys=(269, 101, 57) logical=(912676, 1, 10)
> Partition 2 does not end on cylinder boundary:
> phys=(269, 101, 57) should be (269, 63, 32)
> /dev/sdc3 ? 262490 263179 945973699181456 53 Unknown
> Partition 3 has different physical/logical beginnings (non-Linux?):
> phys=(345, 32, 19) logical=(263178, 26, 16)
> Partition 3 has different physical/logical endings:
> phys=(324, 77, 19) logical=(945972, 51, 15)
> Partition 3 does not end on cylinder boundary:
> phys=(324, 77, 19) should be (324, 63, 32)
> /dev/sdc4 * 680024 680971 680981 10668+ 49 Unknown
> Partition 4 has different physical/logical beginnings (non-Linux?):
> phys=(87, 1, 0) logical=(680970, 34, 16)
> Partition 4 has different physical/logical endings:
> phys=(335, 78, 2) logical=(680980, 61, 8)
> Partition 4 does not end on cylinder boundary:
> phys=(335, 78, 2) should be (335, 63, 32)
>
> ---------- end -------------
Ack, looks like the standard dos/mac formatting trick. Try sdc4:
mount /dev/sdc4 /jaz
Or if it doesn't detect it:
mount -t vfat /dev/sdc4 /jaz
mount -t msdos /dev/sdc4 /jaz
You may also want to try sdc1 and sdc3 if 4 doesn't work.
HTH,
Brandon
+--- ---+
| Brandon Mitchell * bhmit1@mail.wm.edu * http://bhmit1.home.ml.org/ |
| Sometimes you have to release software with bugs. - MS Recruiter |
Reply to: