Grabes problemas con Mobile AMD Athlon(tm) 64 Processor 3000+ , Aperture from northbridge cpu 0 too small (32 MB)
he instalada debian en un portátil con este micro, tanto la versión de
64 bits, como la de 32 (esta desde guadalinex y después actualizada.
Con las dos tengo problemas de segundos muertos y el tiempo que cuenta
el reloj va disparado, esto lo hace casi in usable, pues el ratón se
descontróla y los programas se vuelven impredicibles.
Le he instalado el powernowd pero no cambia nada.
en el dmesg se repite mucho
APIC error on CPU0: 40(40)
yo he visto lo siguiente:
Aperture from northbridge cpu 0 too small (32 MB)
pero no se si es el culpable y como arreglarlo
¿Alguna ayuda?
a continuación pego el dmesg por si sirve de algo
Bootdata ok (command line is root=/dev/hda6 ro )
Linux version 2.6.10 (root@pepe-movil) (gcc versión 3.3.5 (Debian
1:3.3.5-12)) #5 Sun Apr 24 15:12:54 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 130880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 MSI ) @
0x00000000000f8320
ACPI: RSDT (v001 MSI 1029 0x03012005 MSFT 0x00000097) @
0x000000001ff40000
ACPI: FADT (v002 MSI 1029 0x03012005 MSFT 0x00000097) @
0x000000001ff40200
ACPI: MADT (v001 MSI OEMAPIC 0x03012005 MSFT 0x00000097) @
0x000000001ff40300
ACPI: WDRT (v001 MSI MSI_OEM 0x03012005 MSFT 0x00000097) @
0x000000001ff40360
ACPI: MCFG (v001 MSI OEMMCFG 0x03012005 MSFT 0x00000097) @
0x000000001ff403b0
ACPI: SSDT (v001 OEM_ID OEMTBLID 0x00000001 INTL 0x02002026) @
0x000000001ff434b0
ACPI: OEMB (v001 MSI MSI_OEM 0x03012005 MSFT 0x00000097) @
0x000000001ff50040
ACPI: DSDT (v001 MSI 1029 0x03012005 INTL 0x02002026) @
0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 2dd2000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Built 1 zonelists
Kernel command line: root=/dev/hda6 ro console=tty0
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1989.885 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 506600k/523520k available (1720k kernel code, 16180k reserved,
988k data, 148k init)
Calibrating delay loop... 3915.77 BogoMIPS (lpj=1957888)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Mobile AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC NMI watchdog using perfctr0
Using local APIC timer interrupts.
Detected 12.436 MHz APIC timer.
checking if image is initramfs...it isn't (bad gzip magic numbers);
looks like an initrd
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 6)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 7 10 11 12 14 15) *0,
disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1117543969.165:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Linux agpgart interface v0.100 (c) Dave Jones
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
ACPI: PCI interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
POP2 RTL AC97 MC97
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4120KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
Probing IDE interface ide0...
hda: SAMSUNG MP0804H, ATA DISK drive
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-K15, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 > p4
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
APIC error on CPU0: 00(40)
APIC error on CPU0: 40(40)
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
APIC error on CPU0: 40(40)
Adding 1020088k swap on /dev/hda9. Priority:-1 extents:1
EXT3 FS on hda6, internal journal
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio2
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: RealTek RTL8139 at 0xffffff000009ac00, 00:0c:76:f7:c4:67, IRQ 18
eth0: Identified 8139 chip type 'RTL-8101'
SCSI subsystem initialized
Real Time Clock Driver v1.12
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies,
Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 424 MBytes.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[fglrx] module loaded - fglrx 8.12.10 [Apr 4 2005] on minor 0
ACPI: PCI interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: Processor [CPU1] (supports C1 C2 C3)
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version
1.00.09e)
powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x13 (1075 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x8 (1350 mV)
powernow-k8: 3 : fid 0xc (2000 MHz), vid 0x4 (1450 mV)
cpu_init done, current fid 0xc, vid 0x4
i2c /dev entries driver
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and
petero2@telia.com
irda_init()
NET: Registered protocol family 23
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 19 (level, low) -> IRQ 19
Yenta: CardBus bridge found at 0000:02:04.0 [1462:0291]
Yenta: ISA IRQ mask 0x04b8, PCI irq 19
Socket status: 30000006
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 20 (level, low) -> IRQ 20
Yenta: CardBus bridge found at 0000:02:04.1 [1462:0291]
Yenta: ISA IRQ mask 0x04b8, PCI irq 20
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:04.2[C] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[21]
MMIO=[fbfff000-fbfff7ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00007e5c8b]
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
APIC error on CPU0: 40(40)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: PCI device 1002:4374 (ATI Technologies Inc)
ohci_hcd 0000:00:13.0: irq 19, pci mem 0xfbdfd000
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: PCI device 1002:4375 (ATI Technologies Inc)
ohci_hcd 0000:00:13.1: irq 19, pci mem 0xfbdfe000
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 1-2: new low speed USB device using ohci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [1241:1166] on usb-0000:00:13.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ACPI: PCI interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: PCI device 1002:4373 (ATI Technologies Inc)
ehci_hcd 0000:00:13.2: irq 19, pci mem 0xfbdff000
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct
2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using ohci_hcd and address 3
input: USB HID v1.10 Mouse [1241:1166] on usb-0000:00:13.0-2
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
eth0: link down
NET: Registered protocol family 17
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Thermal Zone [THRM] (73 C)
lp: driver loaded but no devices found
APIC error on CPU0: 40(40)
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }
ide: failed opcode was: 0xef
hdc: drive_cmd: status=0x41 { DriveReady Error }
hdc: drive_cmd: error=0x04Aborted Command
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff8036ef60(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
mtrr: base(0xf0000000) is not aligned on a size(0x3ff0000) boundary
[fglrx:firegl_addmap] *ERROR* mtrr allocation failed (-22)
[fglrx] free PCIe = 51118080
[fglrx] max PCIe = 51118080
[fglrx] free LFB = 52654080
[fglrx] max LFB = 52654080
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total PCIe = 16384
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
--
Antonio Trujillo Carmona <trujo@dti2.net>
Reply to: