Re: Placa de fibra optica Qlogic
Sim, funciona. Consigo montar o storage sem problemas, gravar, etc...
Abs
Maxwillian Miorim <miorimmax@gmail.com> escreveu: On 5/18/07, Luis Clemente wrote:
> Olá Max,
>
> Então, uso o ETCH com o kernel 2.6.18-4 default. Vou te mandar as saídas
> do dmesg no momento da detecção do device pnp na inicialização do Debian e
> depois com a reinstalação do módulo manualmente com os comandos rmmod e
> modprobe.
>
> via pnp:
>
> QLogic Fibre Channel HBA Driver
> ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 73 (level, low) -> IRQ 201
> qla2xxx 0000:05:01.0: Found an ISP2312, irq 201, iobase 0xf882c000
> qla2xxx 0000:05:01.0: Configuring PCI space...
> qla2xxx 0000:05:01.0: Configure NVRAM parameters...
> qla2xxx
0000:05:01.0: Verifying loaded RISC code...
> qla2xxx 0000:05:01.0: Firmware image unavailable.
> qla2xxx 0000:05:01.0: Firmware images can be retrieved from:
> ftp://ftp.qlogic.com/outgoing/linux/firmware/.
> qla2xxx 0000:05:01.0: Failed to initialize adapter
> ACPI: PCI interrupt for device 0000:05:01.0 disabled
> ACPI: PCI interrupt for device 0000:05:01.0 disabled
>
>
> reinstalação manual do módulo qla2xxx
>
> QLogic Fibre Channel HBA Driver
> PCI: Enabling device 0000:05:01.0 (0150 -> 0153)
> ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 73 (level, low) -> IRQ 201
> qla2xxx 0000:05:01.0: Found an ISP2312, irq 201, iobase 0xf8840000
> qla2xxx 0000:05:01.0: Configuring PCI space...
> qla2xxx 0000:05:01.0: Configure NVRAM parameters...
> qla2xxx 0000:05:01.0: Verifying loaded RISC code...
> qla2xxx 0000:05:01.0: Allocated (412 KB) for firmware
dump...
> qla2xxx 0000:05:01.0: Waiting for LIP to complete...
> qla2xxx 0000:05:01.0: LOOP UP detected (2 Gbps).
> qla2xxx 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> scsi4 : qla2xxx
> qla2xxx 0000:05:01.0:
> QLogic Fibre Channel HBA Driver: 8.01.07-k1
> QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
> ISP2312: PCI-X (133 MHz) @ 0000:05:01.0 hdma+, host#=4, fw=3.03.20 IPX
> Vendor: HITACHI Model: OPEN-V*16 Rev: 2114
> Type: Direct-Access ANSI SCSI
> revision: 02
É bem estranho, manualmente parece não dar problema...
Faz o download do firmware apropriado do site da qlogic[1], depois
copia o binário (a menos que queira baixar o fonte (os .C) e
compilar...) para /lib/firmware.
A propósito, carregando "manualmente" funciona?
1 -
http://support.qlogic.com/support/product_resources.asp?id=583
__________________________________________________
Fale com seus amigos de graça com o novo Yahoo! Messenger
http://br.messenger.yahoo.com/
Reply to: