[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: Placa de fibra optica Qlogic

On 5/18/07, Luis Clemente <luispsl@yahoo.com.br> wrote:

Olá Max,

    Então, uso o ETCH com o kernel 2.6.18-4 default. Vou te mandar as saídas
do dmesg no momento da detecção do device pnp na inicialização do Debian e
depois com a reinstalação do módulo manualmente com os comandos rmmod e
modprobe.

via pnp:

QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 73 (level, low) -> IRQ 201
qla2xxx 0000:05:01.0: Found an ISP2312, irq 201, iobase 0xf882c000
qla2xxx 0000:05:01.0: Configuring PCI space...
qla2xxx 0000:05:01.0: Configure NVRAM parameters...
qla2xxx 0000:05:01.0: Verifying loaded RISC code...
qla2xxx 0000:05:01.0: Firmware image unavailable.
qla2xxx 0000:05:01.0: Firmware images can be retrieved from:
ftp://ftp.qlogic.com/outgoing/linux/firmware/.
qla2xxx 0000:05:01.0: Failed to initialize adapter
ACPI: PCI interrupt for device 0000:05:01.0 disabled
ACPI: PCI interrupt for device 0000:05:01.0 disabled


reinstalação manual do módulo qla2xxx

QLogic Fibre Channel HBA Driver
PCI: Enabling device 0000:05:01.0 (0150 -> 0153)
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 73 (level, low) -> IRQ 201
qla2xxx 0000:05:01.0: Found an ISP2312, irq 201, iobase 0xf8840000
qla2xxx 0000:05:01.0: Configuring PCI space...
qla2xxx 0000:05:01.0: Configure NVRAM parameters...
qla2xxx 0000:05:01.0: Verifying loaded RISC code...
qla2xxx 0000:05:01.0: Allocated (412 KB) for firmware dump...
qla2xxx 0000:05:01.0: Waiting for LIP to complete...
qla2xxx 0000:05:01.0: LOOP UP detected (2 Gbps).
qla2xxx 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
scsi4 : qla2xxx
qla2xxx 0000:05:01.0:
 QLogic Fibre Channel HBA Driver: 8.01.07-k1
  QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
  ISP2312: PCI-X (133 MHz) @ 0000:05:01.0 hdma+, host#=4, fw=3.03.20 IPX
  Vendor: HITACHI   Model: OPEN-V*16         Rev: 2114
  Type:   Direct-Access                      ANSI SCSI
revision: 02


É bem estranho, manualmente parece não dar problema...

Faz o download do firmware apropriado do site da qlogic[1], depois
copia o binário (a menos que queira baixar o fonte (os .C) e
compilar...) para /lib/firmware.

A propósito, carregando "manualmente" funciona?

1 - http://support.qlogic.com/support/product_resources.asp?id=583
Reply to: