Sorgen nach smartctl
Hallo,
nach dem ich bei mir mal meine beiden Festplatten mit smartctl getestet habe
mache ich mir nun Sorgen. Leider kann ich die Error Meldungen nicht deuten.
Aber da mir nichts gravierendes an Fehlern auffällt frage ich mich nun ob sich
was anbahnen könnte.
dlx:/home/sigi# smartctl -a /dev/hdd
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model: ST3160021A
Serial Number: 5JS178X3
Firmware Version: 3.06
User Capacity: 160.041.885.696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Mon Jan 7 22:01:40 2008 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 111) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 056 052 006 Pre-fail
Always - 212966076
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 4
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail
Always - 176727751
9 Power_On_Hours 0x0032 093 093 000 Old_age
Always - 6296
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age
Always - 2980
194 Temperature_Celsius 0x0022 028 057 000 Old_age
Always - 28
195 Hardware_ECC_Recovered 0x001a 056 052 000 Old_age
Always - 212966076
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 193 000 Old_age
Always - 88
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age
Always - 0
SMART Error Log Version: 1
ATA Error Count: 81 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 81 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 1b db 0f f0 Error: ICRC, ABRT 1 sectors at LBA = 0x000fdb1b =
1039131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 b4 da 0f f0 00 05:22:45.602 READ DMA EXT
25 00 68 b4 da 0f f0 00 05:22:45.601 READ DMA EXT
10 00 3f 00 00 00 f0 00 05:22:45.594 RECALIBRATE [OBS-4]
25 00 68 b4 da 0f f0 00 05:22:45.565 READ DMA EXT
25 00 68 b4 da 0f f0 00 05:22:45.565 READ DMA EXT
Error 80 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 1b db 0f f0 Error: ICRC, ABRT 1 sectors at LBA = 0x000fdb1b =
1039131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 b4 da 0f f0 00 05:22:45.602 READ DMA EXT
10 00 3f 00 00 00 f0 00 05:22:45.601 RECALIBRATE [OBS-4]
25 00 68 b4 da 0f f0 00 05:22:45.594 READ DMA EXT
25 00 68 b4 da 0f f0 00 05:22:45.565 READ DMA EXT
25 00 38 7c da 0f f0 00 05:22:45.565 READ DMA EXT
Error 79 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 1b db 0f f0 Error: ICRC, ABRT 1 sectors at LBA = 0x000fdb1b =
1039131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 b4 da 0f f0 00 05:22:45.602 READ DMA EXT
25 00 68 b4 da 0f f0 00 05:22:45.601 READ DMA EXT
25 00 38 7c da 0f f0 00 05:22:45.594 READ DMA EXT
25 00 20 5c da 0f f0 00 05:22:45.565 READ DMA EXT
25 00 08 54 da 0f f0 00 05:22:45.565 READ DMA EXT
Error 78 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 1b db 0f f0 Error: ICRC, ABRT 1 sectors at LBA = 0x000fdb1b =
1039131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 b4 da 0f f0 00 05:22:45.602 READ DMA EXT
25 00 38 7c da 0f f0 00 05:22:45.601 READ DMA EXT
25 00 20 5c da 0f f0 00 05:22:45.594 READ DMA EXT
25 00 08 54 da 0f f0 00 05:22:45.565 READ DMA EXT
25 00 18 0f b1 10 f0 00 05:22:45.565 READ DMA EXT
Error 77 occurred at disk power-on lifetime: 361 hours (15 days + 1 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 1b db 0f f0 Error: ICRC, ABRT 1 sectors at LBA = 0x000fdb1b =
1039131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 b4 da 0f f0 00 04:37:47.255 READ DMA EXT
25 00 68 b4 da 0f f0 00 04:37:47.255 READ DMA EXT
10 00 3f 00 00 00 f0 00 04:37:40.318 RECALIBRATE [OBS-4]
25 00 68 b4 da 0f f0 00 04:37:40.310 READ DMA EXT
25 00 68 b4 da 0f f0 00 04:37:40.310 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
##############
dlx:/home/sigi# smartctl -a /dev/hda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model: ST340014A
Serial Number: 5JX0D218
Firmware Version: 3.04
User Capacity: 40.020.664.320 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Tue Jan 8 01:27:37 2008 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 062 056 006 Pre-fail
Always - 126792745
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 29
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail
Always - 470786764
9 Power_On_Hours 0x0032 088 088 000 Old_age
Always - 10889
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 095 095 020 Old_age
Always - 5455
194 Temperature_Celsius 0x0022 031 054 000 Old_age
Always - 31
195 Hardware_ECC_Recovered 0x001a 062 056 000 Old_age
Always - 126792745
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age
Always - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 541 hours (22 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 fe ff ff e3 Error: IDNF 8 sectors at LBA = 0x03fffffe = 67108862
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 fe ff ff e3 00 03:42:04.326 READ DMA
c8 00 08 f6 ff ff e3 00 03:42:04.325 READ DMA
c8 00 08 ee ff ff e3 00 03:42:04.325 READ DMA
c8 00 08 e6 ff ff e3 00 03:42:04.325 READ DMA
c8 00 08 de ff ff e3 00 03:42:05.216 READ DMA
Error 1 occurred at disk power-on lifetime: 541 hours (22 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 80 c6 ff ff e3 Error: IDNF 128 sectors at LBA = 0x03ffffc6 = 67108806
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 c6 ff ff e3 00 03:42:02.868 READ DMA
ca 00 01 c5 ff ff e3 00 03:42:02.868 WRITE DMA
ca 00 07 be ff ff e3 00 03:42:02.868 WRITE DMA
ca 00 78 46 ff ff e3 00 03:42:02.866 WRITE DMA
c8 00 80 46 ff ff e3 00 03:42:02.864 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 3895 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gruß Sigi
Reply to: