[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: Dateisystem hinüber?



Hallo Gerhard,

Am Freitag 28 Dezember 2007 schrieb Gerhard Lindel:
> Simon Jolle "sjolle" schrieb:
[...]

> Hallo Simon,
> in den Logfiles finde ich nichts aufregendes, also keine
> Fehlermeldungen. Dass ich die Elemente aus lost&found nicht mehr
> zusammenbekomme ist schon klar. Da ist eine Neuinstallation einfacher.
> Mit smartctl bekomme ich folgendes:
>
>
> === START OF INFORMATION SECTION ===
> Device Model:     SAMSUNG SP1614N
> Serial Number:    S016J10XA22823
> Firmware Version: TM100-24
> User Capacity:    160.041.885.696 bytes
> Device is:        In smartctl database [for details use: -P show]
> ATA Version is:   7
> ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0
> Local Time is:    Fri Dec 28 21:24:54 2007 CET
> SMART support is: Available - device has SMART capability.
> SMART support is: Disabled

Den würde ich mal einschalten, z.B.:

smartctl -s on /dev/sda

> Warning! SMART Attribute Data Structure error: invalid SMART checksum.
> Warning! SMART Attribute Thresholds Structure error: invalid SMART
> checksum. === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
> See vendor-specific Attribute list for marginal Attributes.
>
> General SMART Values:
> Offline data collection status:  (0xff) Offline data collection
> activity is in a Vendor Specific state .
>                                         Auto Offline Data Collection:
> Enabled.
> Self-test execution status:      ( 255) Self-test routine in
> progress... 150% of test remaining. 

Da scheinen die smartmontools oder die Platte etwas durcheinander zu sein. 
Mehr als 100% verbleibend machen nicht wirklich Sinn.


> SMART Attributes Data Structure revision number: 65535
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE
> UPDATED  WHEN_FAILED RAW_VALUE
> 255 Unknown_Attribute       0xffff   255   255   255    Pre-fail
> Always   FAILING_NOW 281474976710655
> 255 Unknown_Attribute       0xffff   255   255   255    Pre-fail
> Always   FAILING_NOW 281474976710655

Das sieht nicht gut aus. Initial sollte alle Werte nicht gerade bei 
FAILING_NOW stehen. Andererseits sieht das so aus, als ob die Werte 
einfach nicht initialisiert sind. Sowas habe ich noch nie gesehen.

Selbst meine neue Platte hatte direkt nach dem Einschalten des 
SMART-Supports brauchbare Werte:

SMART support is: Available - device has SMART capability.
SMART support is: Enabled
[...]
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  
WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   062    Pre-fail  
Always       -       0
  2 Throughput_Performance  0x0005   100   100   040    Pre-fail  
Offline      -       0
  3 Spin_Up_Time            0x0007   153   153   033    Pre-fail  
Always       -       1
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   
Always       -       20
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  
Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  
Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   040    Pre-fail  
Offline      -       0
  9 Power_On_Hours          0x0012   100   100   000    Old_age   
Always       -       8
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  
Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   
Always       -       10
191 G-Sense_Error_Rate      0x000a   100   100   000    Old_age   
Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   
Always       -       3
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   
Always       -       214
194 Temperature_Celsius     0x0002   148   148   000    Old_age   
Always       -       37 (Lifetime Min/Max 18/40)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   
Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   
Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   
Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   
Always       -       0
223 Load_Retry_Count        0x000a   100   100   000    Old_age   
Always       -       0

Vielleicht musst Du den SMART-Support wirklich erst einschalten, um 
brauchbare Werte zu bekommen. Bei mir hat er dann allerdings einfach gar 
keine Werte geliefert, solange unter GRML beim Rückspielen der Daten der 
SMART-Support noch aus war.

Vielleicht brauchst Du für die Platte auch eine neuere Version von 
Smartmontools, da den Smartmontools evtl. die Attribute für die Platte 
unbekannt sind. Nun da gibt es eine Mailingliste bei 
http://smartmontools.sourceforge.net/

Ansonsten ist ein Test mit dem Hersteller-Tool wohl am sinnvollsten. Denn 
wenn das zeigt, die Platte ist hinüber, sollte innerhalb der Garantiezeit 
ein Austausch nun wirklich kein Problem sein.

> Warning! SMART Self-Test Log Structure error: invalid SMART checksum.

Okay, da ist offenbar mit dem SMART-Zeug etwas ziemlich kaputt. Oder die 
Smartmontools kommen mit der Platte nicht klar und Du brauchst eine 
neuere Version.

> SMART Self-test log structure revision number 65535

Scheint das der Datenbereich für SMART auf der Platte aus lauter gesetzten 
Bits (255, 255, 255, FF, FF, FF oder 11111111, 11111111, 11111111 ;-) 
besteht, was so sicherlich nicht im Sinne des Erfinders ist.

> Warning: ATA Specification requires self-test log structure revision
> number = 1
> Num  Test_Description    Status                  Remaining
> LifeTime(hours)  LBA_of_first_error
> # 1  Vendor offline      Self-test routine in progress 150%
> 65535         -
> # 2  Vendor offline      Self-test routine in progress 150%
> 65535         -
> # 3  Vendor offline      Self-test routine in progress 150%
> 65535         -

Hmmm, auch das ergibt für mich keinen Sinn. Du bekommst wahrscheinlich 
mehr Hilfe, wenn Du die smartctl-Ausgabe auf die 
smartmontools-Mailingliste postest.

Guten Rutsch ins neue Jahr schonmal vorbeugend... ;-)

Ciao,
-- 
Martin 'Helios' Steigerwald - http://www.Lichtvoll.de
GPG: 03B0 0D6C 0040 0710 4AFA  B82F 991B EAAC A599 84C7

Attachment: signature.asc
Description: This is a digitally signed message part.


Reply to: