On Thu, Dec 13, 2007 at 12:17:26AM +0100, Siegfrid Brandstätter wrote:
> Hallo Paul,
> Am Mittwoch, 12. Dezember 2007 schrieb Paul Puschmann:
> > Siegfrid Brandstätter <garafrut@web.de> schrieb am Wed, Dec 12, 2007 at
> 01:38:07AM +0100:
> > > Aber eine DVD geht genausowenig wie mit -486. An was das wohl liegt,
> > > w32codec und libdvdcss2 sind installiert. Aber weder Kaffeine, VLC, und
> > > Mplayer schon gar nicht, der will überhaupt nichts spielen. Die anderen
> > > versuchen es zumindest, zwar nur mit stottern des Bild und Tons. Aber
> > > immerhin.
> > >
> > > Habe nun 877MB in der Anzeige von gkrellm für RAM, zuvor waren es 884MB??
> >
> > Nimm mal "radeon" als X11-Modul statt fglrx. Zumindest testweise.
> > Was segt dein DMA-Status (DVD-Laufwerk). Kannst du mit hdparm
> > herausfinden und ändern.
> >
> Danke Dir für die Tipps,
>
> Die Mplayer Meldung finde ich echt gut:
> "Your system is too SLOW to play this!"
> Frage mich nur warum es dann auf meinem PC spielt?
>
> hier einige Ergebnisse, sind leider etwas mehr:
>
>
> # hdparm -v -i /dev/hda
>
> /dev/hda:
> IO_support = 0 (default 16-bit)
> unmaskirq = 0 (off)
> using_dma = 1 (on)
> keepsettings = 0 (off)
> readonly = 0 (off)
> readahead = 256 (on)
> HDIO_GETGEO failed: Bad address
>
> Model=MATSHITADVD-RAM UJ-850S, FwRev=1.21, SerialNo=HC71 179139
> Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
> RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
> BuffType=unknown, BuffSize=0kB, MaxMultSect=0
> (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
> IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2
> AdvancedPM=no
> Drive conforms to: Unspecified: ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5
> ATA/ATAPI-6 ATA/ATAPI-7
>
> * signifies the current active mode
>
> Was könnte ich hier ändern?
Sieht so ganz gut aus. DMA ist aktiviert (wichtig). 32-Bit Mode muss
nicht unbedingt sein.
> ##########
> Aus der Xorg.conf nach ändern: Hoffe das richtige geändert zu haben (Nimm
> mal "radeon" als X11-Modul statt fglrx) Habe aber danach keinen reboot
> gemacht, nur gespeichert.
Du brauchst auch normalerweise nur den X-Server stoppen
(bzw. kdm/gdm), dann evtl. das Modul fglrx entladen (rmmod) und dann
den X-Server (oder kdm / gdm) wieder starten.
> Section "Device"
> Identifier "Tarjeta de vídeo genérica"
> Driver "radeon"
> BusID "PCI:1:5:0"
> EndSection
>
> Section "Device"
> Identifier "aticonfig-Device[0]"
> Driver "radeon" hier stand zuvor "flgrx"
> EndSection
>
> Section "Screen"
> Identifier "Default Screen"
> Device "Tarjeta de vídeo genérica"
> Monitor "Monitor genérico"
> DefaultDepth 24
> SubSection "Display"
> Depth 1
> Modes "1024x768" "800x600" "640x480"
> |--|
>
> SubSection "Display"
> Depth 24
> Modes "1024x768" "800x600" "640x480"
> EndSubSection
> EndSection
>
> Section "Screen"
> Identifier "aticonfig-Screen[0]"
> Device "aticonfig-Device[0]"
> Monitor "aticonfig-Monitor[0]"
> DefaultDepth 24
> SubSection "Display"
> Viewport 0 0
> Depth 24
> EndSubSection
> EndSection
>
> Section "DRI"
> Mode 0666
> EndSection
>
> ###################################
>
> Hier die verschiedenen Ausgaben der Div. Player:
>
> aus /home/.mplayer/gui.conf
>
> enable_audio_equ = "no"
> vo_driver = "xv" ### habe ich schon ausgebessert von "xmga"##
> vo_panscan = "0.000000"
> vo_doublebuffering = "yes"
> vo_direct_render = "no"
> vo_dxr3_device = "/dev/em8300-0"
> v_framedrop = "0"
> v_flip = "-1"
> v_ni = "no"
> v_idx = "-1"
> vf_pp = "no"
> vf_autoq = "0"
> vf_lavc = "no"
> ao_driver = "alsa"
> ao_volnorm = "no"
> softvol = "no"
> ao_surround = "no"
> ao_extra_stereo = "no"
> ao_extra_stereo_coefficient = "1.000000"
> dvd_device = "/dev/dvd"
> osd_level = "1"
> sub_auto_load = "yes"
> sub_unicode = "no"
> ass_enabled = "no"
> ass_use_margins = "no"
> ass_top_margin = "0"
> ass_bottom_margin = "0"
> sub_pos = "100"
> sub_overlap = "no"
> font_factor = "0.750000"
> font_name = "Sans"
> font_text_scale = "3.000000"
> font_osd_scale = "6.000000"
> font_blur = "2.000000"
> font_outline = "2.000000"
> font_autoscale = "3"
> cache = "no"
> cache_size = "2048"
> playbar = "yes"
> load_fullscreen = "no"
> show_videowin = "yes"
> stopxscreensaver = "yes"
> autosync = "no"
> autosync_size = "0"
> gui_skin = "default"
> gui_save_pos = "yes"
> gui_main_pos_x = "588"
> gui_main_pos_y = "669"
> gui_video_out_pos_x = "109"
> gui_video_out_pos_y = "133"
> equ_channel_1 = "Front Right"
> equ_channel_2 = "Front Left"
> equ_channel_3 = "Rear Right"
> equ_channel_4 = "Rear Left"
> equ_channel_5 = "Center"
> equ_channel_6 = "Bass"
> equ_band_00 = "0.000000"
>
> ######################################
>
> gmplayer, startet-spielt aber ohne Bild, Ton laeuft.
>
> sebastian@debian:~$ gmplayer dvd://1
> MPlayer dev-SVN-rUNKNOWN-4.1.2 (C) 2000-2007 MPlayer Team
> CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-56 (Family: 15, Model: 104,
> Stepping: 1)
> CPUflags: MMX: 1 MMX2: 1 3DNow: 1 3DNow2: 1 SSE: 1 SSE2: 1
> Compiled with runtime CPU detection.
> Can't open joystick device /dev/input/js0: No such file or directory
> Can't init input joystick
> mplayer: could not connect to socket
> mplayer: No such file or directory
> Failed to open LIRC support. You will not be able to use your remote control.
>
> Playing dvd://1.
> libdvdread: Using libdvdcss version 1.2.9 for DVD access
> There are 14 titles on this DVD.
> There are 26 chapters in this DVD title.
> There are 1 angles in this DVD title.
>
> libdvdread: Attempting to retrieve all CSS keys
> libdvdread: This can take a _long_ time, please be patient
>
> libdvdread: Get key for /VIDEO_TS/VIDEO_TS.VOB at 0x0000013d
> |--|
> libdvdread: Elapsed time 0
> libdvdread: Get key for /VIDEO_TS/VTS_06_1.VOB at 0x003b1d60
> libdvdread: Elapsed time 0
> libdvdread: Found 6 VTS's
> libdvdread: Elapsed time 0
> audio stream: 0 format: lpcm (stereo) language: de aid: 160.
> number of audio channels on disk: 1.
> number of subtitles on disk: 0
> MPEG-PS file format detected.
> VIDEO: MPEG2 720x576 (aspect 3) 25.000 fps 7700.0 kbps (962.5 kbyte/s)
> [VO_XV] It seems there is no Xvideo support for your video card available.
> [VO_XV] Run 'xvinfo' to verify its Xv support and read
> [VO_XV] DOCS/HTML/en/video.html#xv!
> [VO_XV] See 'mplayer -vo help' for other (non-xv) video out drivers.
> [VO_XV] Try -vo x11.
> Error opening/initializing the selected video_out (-vo) device.
> ==========================================================================
> Opening audio decoder: [dvdpcm] Uncompressed DVD/VOB LPCM audio decoder
> AUDIO: 48000 Hz, 2 ch, s16be, 1536.0 kbit/100.00% (ratio: 192000->192000)
> Selected audio codec: [dvdpcm] afm: dvdpcm (Uncompressed DVD/VOB LPCM)
> ==========================================================================
> AO: [alsa] 48000Hz 2ch s16be (2 bytes per sample)
> Video: no video
> Starting playback...
>
> ############################
>
> Mplayer von GUI gestartet:
> Error-opening/ initialing the selectet video-out(-vo)device
>
> Mit:
> $ mplayer dvd://1.
> GUI kommt keine, Einstellungen sind unmoeglich auszufuehren, links u.
> rechtsklick auf Bild geht nicht. Bild verzerrt, zu klein Ton stottert usw.
>
> Playing dvd://1.
> libdvdread: Using libdvdcss version 1.2.9 for DVD access
> There are 14 titles on this DVD.
> There are 26 chapters in this DVD title.
> There are 1 angles in this DVD title.
>
> libdvdread: Attempting to retrieve all CSS keys
> libdvdread: This can take a _long_ time, please be patient
>
> libdvdread: Get key for /VIDEO_TS/VIDEO_TS.VOB at 0x0000013d
> libdvdread: Elapsed time 0
> |--|
>
> libdvdread: Elapsed time 0
> libdvdread: Get key for /VIDEO_TS/VTS_06_1.VOB at 0x003b1d60
> libdvdread: Elapsed time 0
> libdvdread: Found 6 VTS's
> libdvdread: Elapsed time 0
> audio stream: 0 format: lpcm (stereo) language: de aid: 160.
> number of audio channels on disk: 1.
> number of subtitles on disk: 0
> MPEG-PS file format detected.
> VIDEO: MPEG2 720x576 (aspect 3) 25.000 fps 7700.0 kbps (962.5 kbyte/s)
> open: No such file or directory
> [MGA] Couldn't open: /dev/mga_vid
> open: No such file or directory
> [MGA] Couldn't open: /dev/mga_vid
> [VO_TDFXFB] Can't open /dev/fb0: No such file or directory.
> s3fb: can't open /dev/fb0: No such file or directory
> [VO_XV] It seems there is no Xvideo support for your video card available.
> [VO_XV] Run 'xvinfo' to verify its Xv support and read
> [VO_XV] DOCS/HTML/en/video.html#xv!
> [VO_XV] See 'mplayer -vo help' for other (non-xv) video out drivers.
> [VO_XV] Try -vo x11.
> ==========================================================================
> Opening video decoder: [mpegpes] MPEG 1/2 Video passthrough
> VDec: vo config request - 720 x 576 (preferred colorspace: Mpeg PES)
> Could not find matching colorspace - retrying with -vf scale...
> Opening video filter: [scale]
> The selected video_out device is incompatible with this codec.
> Try appending the scale filter to your filter list,
> e.g. -vf spp,scale instead of -vf spp.
> VDecoder init failed :(
> Opening video decoder: [libmpeg2] MPEG 1/2 Video decoder libmpeg2-v0.4.0b
> Selected video codec: [mpeg12] vfm: libmpeg2 (MPEG-1 or 2 (libmpeg2))
> ==========================================================================
> ==========================================================================
> Opening audio decoder: [dvdpcm] Uncompressed DVD/VOB LPCM audio decoder
> AUDIO: 48000 Hz, 2 ch, s16be, 1536.0 kbit/100.00% (ratio: 192000->192000)
> Selected audio codec: [dvdpcm] afm: dvdpcm (Uncompressed DVD/VOB LPCM)
> ==========================================================================
> AO: [alsa] 48000Hz 2ch s16be (2 bytes per sample)
> Starting playback...
> VDec: vo config request - 720 x 576 (preferred colorspace: Planar YV12)
> VDec: using Planar YV12 as output csp (no 0)
> Movie-Aspect is 1.78:1 - prescaling to correct movie aspect.
> VO: [x11] 720x576 => 1024x576 Planar YV12
> [swscaler @ 0x8441c10]SwScaler: using unscaled yuv420p -> rgb32 special
> converter
> A: 3.5 V: 2.2 A-V: 1.391 ct: 0.122 55/ 55 11% 146% 0.7% 50 0
>
> ************************************************
> **** Your system is too SLOW to play this! ****
> ************************************************
>
> Possible reasons, problems, workarounds:
> - Most common: broken/buggy _audio_ driver
> - Try -ao sdl or use the OSS emulation of ALSA.
> - Experiment with different values for -autosync, 30 is a good start.
> - Slow video output
> - Try a different -vo driver (-vo help for a list) or try -framedrop!
> - Slow CPU
> - Don't try to play a big DVD/DivX on a slow CPU! Try some of the lavdopts,
> e.g. -vfm ffmpeg -lavdopts lowres=1:fast:skiploopfilter=all.
> - Broken file
> - Try various combinations of -nobps -ni -forceidx -mc 0.
> - Slow media (NFS/SMB mounts, DVD, VCD etc)
> - Try -cache 8192.
> - Are you using -cache to play a non-interleaved AVI file?
> - Try -nocache.
> Read DOCS/HTML/en/video.html for tuning/speedup tips.
> If none of this helps you, read DOCS/HTML/en/bugreports.html
>
> Too many video packets in the buffer: (4096 in 8272675 bytes).
> Maybe you are playing a non-interleaved stream/file or the codec failed?
> For AVI files, try to force non-interleaved mode with the -ni option.
>
> Too many video packets in the buffer: (4096 in 8272675 bytes).
> Maybe you are playing a non-interleaved stream/file or the codec failed?
> For AVI files, try to force non-interleaved mode with the -ni option.
> A: 33.1 V: 24.8 A-V: 8.276 ct: 1.243 622/622 10% 145% 0.8% 337 0
>
> 33333333333333333333333333333333333
>
> Mit Kaffeine, von GUI kein start moeglich:
>
> Meldung:
> moeglicherweise nicht genug Rechte oder keine CD.
>
> Die selbe Meldung bei:
>
> sebastian@debian:~$ kaffeine dvd://1
> 0
> QLayout "unnamed" added to QWidget "unnamed", which already has a layout
> Xlib: extension "XFree86-DRI" missing on display ":0.0".
> video_out_opengl: compiled for BGRA output, but missing extension.
> libdvdnav: Using dvdnav version 1.1.2 from http://xine.sf.net
> libdvdread: Using libdvdcss version 1.2.9 for DVD access
> libdvdread: Can't stat //1
> No existe el fichero o el directorio
> libdvdnav: vm: faild to open/read the DVD
> libdvdnav: Using dvdnav version 1.1.2 from http://xine.sf.net
> libdvdread: Using libdvdcss version 1.2.9 for DVD access
> libdvdnav: DVD Title: DVDVolume
> libdvdnav: DVD Serial Number: bc1b790e
> libdvdnav: DVD Title (Alternative): DVDVolume
> libdvdnav: Unable to find map file '/home/sebastian/.dvdnav/DVDVolume.map'
> libdvdnav: DVD disk reports itself with Region mask 0x00fd0000. Regions: 2
>
> libdvdread: Attempting to retrieve all CSS keys
> libdvdread: This can take a _long_ time, please be patient
> |--|
> libdvdread: Elapsed time 0
> libdvdread: Get key for /VIDEO_TS/VTS_06_1.VOB at 0x003b1d60
> libdvdread: Elapsed time 0
> libdvdread: Found 6 VTS's
> libdvdread: Elapsed time 0
> libdvdread: Can't seek to block 3850834
> libdvdread: Invalid IFO for title 5 (VTS_05_0.IFO).
> libdvdnav: ifoOpenVTSI failed
> sebastian@debian:~$ libdvdnav: Using dvdnav version 1.1.2 from
> http://xine.sf.net
> libdvdread: Using libdvdcss version 1.2.9 for DVD access
> libdvdnav: DVD Title: DVDVolume
> libdvdnav: DVD Serial Number: bc1b790e
> libdvdnav: DVD Title (Alternative): DVDVolume
> libdvdnav: Unable to find map file '/home/sebastian/.dvdnav/DVDVolume.map'
> libdvdnav: DVD disk reports itself with Region mask 0x00fd0000. Regions: 2
>
> libdvdread: Attempting to retrieve all CSS keys
> libdvdread: This can take a _long_ time, please be patient
>
> libdvdread: Get key for /VIDEO_TS/VIDEO_TS.VOB at 0x0000013d
> libdvdread: Elapsed time 0
> |--|
> libdvdread: Can't seek to block 3850834
> libdvdread: Invalid IFO for title 5 (VTS_05_0.IFO).
> libdvdnav: ifoOpenVTSI failed
>
Ich frage mich, warum du so viel "mga" in deinen Playern als
Fehlermeldung hast... Hattest du mal eine Matrox-Grafikkarte?
Probier mal den VLC-Player (http://www.videolan.org). Mit den
Standardeinstellungen! Nicht frickeln!
Paul
--
Attachment:
signature.asc
Description: Digital signature