[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

2.6.14 SATA und IDE

Hallo zusammen,

so langsam nervt es mich ... :-) Mein DVD klappt ned.

worf:~# cat /proc/version
Linux version 2.6.14 (lvmbi@worf) (gcc version 4.0.2 (Debian 4.0.2-2)) #1 SMP Mon Oct 31 15:09:24 CET 2005

Bei dmesg gibt es die Meldung ports already in use skipping probe. Jetzt ist da leider das DVD angeschlossen. Weiß jeman Rat ?



Ausgabe von dmesg :

libata version 1.12 loaded.
ata_piix version 1.04
ata_piix: combined mode detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1880 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:5b01 84:4003 85:3469 86:1801 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 156312576 sectors:
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
  Vendor: ATA       Model: WDC WD800JD-08JN  Rev: 06.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1888 irq 15
ata2: dev 0 cfg 49:0f00 82:4210 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
ReiserFS: sda1: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1510068k swap on /dev/sda5.  Priority:-1 extents:1 across:1510068k
EXT3 FS on sda1, internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe

Reply to: