Hallo Liste,
seit dem Umstieg von XFree auf Xorg (stand ja neulich in Etch an)
läuft hier meine Dualhead-Konfiguration nicht mehr.
Ich betreibe an meinem Laptop zusätzlich noch einen 17" TFT Monitor.
Wie schon gesagt, dass ganze im Dualheadbetrieb.
Seit der Umstellung von XFree (4.3.0) auf Xorg (6.8.2) wird vom
Xserver nur noch ein Monitor erkannt.
Seltsamerweise ist dies der externe TFT, nicht etwa das Laptop
Display. Der Laptop bleibt einfach schwarz.
Allerdings lief unter XFree das ganze Problemlos, mit genau der
gleichen Konfig.
Ich häng mal die relevanten Teile aus meiner xorg.conf und den Logs
an. Vielleicht fällt ja einem von Euch auf, wo der Fehler liegt.
Auszug aus meiner xorg.conf:
Section "Device"
Identifier "radeon0"
Driver "radeon"
# Option "AGPMode" "4"
# Option "ShadowFB" "true"
# vendorname "ATI"
Screen 0
BusID "1:0:0"
Option "CloneDisplay" "true"
Option "CloneMode" "1280x1024"
Option "CloneHSync" "30-95"
Option "CloneVRefresh" "50-120"
EndSection
Section "Device"
Identifier "radeon1"
Driver "radeon"
# Option "ShadowFB" "true"
# Option "AGPMode" "4"
# vendorname "ATI"
Screen 1
BusID "1:0:0"
EndSection
Section "Monitor"
Identifier "Laptop"
HorizSync 15-64
VertRefresh 50-85
Option "DPMS"
DisplaySize 300 230
EndSection
Section "Monitor"
Identifier "Medion TFT"
HorizSync 50-80
VertRefresh 30-83
Option "DPMS"
EndSection
Section "Screen"
Identifier "Screen0"
Device "radeon0"
Monitor "Laptop"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1400x1050" "1024x768" "800x600"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "radeon1"
Monitor "Medion TFT"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x1024" "1024x768"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" Above "Screen0"
InputDevice "Generic Keyboard"
InputDevice "Touchpad" "CorePointer"
InputDevice "Mouse" "AlwaysCore"
Option "Xinerama" "off"
Option "Clone" "on"
# Option "TVOut" "on"
# Option "TVStandard" "PAL"
EndSection
Section "ServerFlags"
# Option "Xinerama" "true"
Option "Clone" "true"
EndSection
Hier ein paar Auszüge aus den Logs:
(II) Primary Device is: PCI 01:00:0
(--) Chipset ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP) found
(--) Chipset ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP) found
...
(II) RADEON(0): I2C bus "DDC" initialized.
(II) RADEON(0): Legacy BIOS detected
(II) RADEON(0): LVDS port is not in connector table, added in.
(II) RADEON(0): Connector0: DDCType-0, DACType-1, TMDSType--1,
ConnectorType-1
(II) RADEON(0): Connector1: DDCType-3, DACType-0, TMDSType--1,
ConnectorType-2
(II) RADEON(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) RADEON(0): I2C device "DDC:ddc2" removed.
(II) RADEON(0): DDC Type: 3, Detected Type: 1
(II) RADEON(0): EDID data from the display on port 1
----------------------
(II) RADEON(0): Manufacturer: MED Model: 7744 Serial#: 1068
(II) RADEON(0): Year: 2002 Week: 45
(II) RADEON(0): EDID Version: 1.3
(II) RADEON(0): Analog Display Input, Input Voltage Level:
0.700/0.700 V
(II) RADEON(0): Sync: Separate
(II) RADEON(0): Max H-Image Size [cm]: horiz.: 34 vert.: 27
(II) RADEON(0): Gamma: 2.20
(II) RADEON(0): DPMS capabilities: Suspend Off; RGB/Color Display
(II) RADEON(0): Default color space is primary color space
(II) RADEON(0): First detailed timing is preferred mode
(II) RADEON(0): redX: 0.631 redY: 0.354 greenX: 0.294 greenY:
0.596
(II) RADEON(0): blueX: 0.143 blueY: 0.087 whiteX: 0.300 whiteY:
0.340
(II) RADEON(0): Supported VESA Video Modes:
(II) RADEON(0): 720x400@70Hz
(II) RADEON(0): 640x480@60Hz
(II) RADEON(0): 640x480@72Hz
(II) RADEON(0): 640x480@75Hz
(II) RADEON(0): 800x600@56Hz
(II) RADEON(0): 800x600@60Hz
(II) RADEON(0): 800x600@72Hz
(II) RADEON(0): 800x600@75Hz
(II) RADEON(0): 1024x768@60Hz
(II) RADEON(0): 1024x768@70Hz
(II) RADEON(0): 1024x768@75Hz
(II) RADEON(0): 1280x1024@75Hz
(II) RADEON(0): Manufacturer's mask: 0
(II) RADEON(0): Supported Future Video Modes:
(II) RADEON(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) RADEON(0): Supported additional Video Mode:
(II) RADEON(0): clock: 108.0 MHz Image Size: 338 x 270 mm
(II) RADEON(0): h_active: 1280 h_sync: 1328 h_sync_end 1440
h_blank_end 1688 h_border: 0
(II) RADEON(0): v_active: 1024 v_sync: 1025 v_sync_end 1028
v_blanking: 1066 v_border: 0
(II) RADEON(0): Ranges: V min: 50 V max: 75 Hz, H min: 30 H max:
83 kHz, PixClock max 140 M
Hz
(II) RADEON(0): Monitor name: MD9404QB
(II) RADEON(0): MEDION
(II) RADEON(0):
(II) RADEON(0): Primary:
Monitor -- CRT
Connector -- VGA
DAC Type -- Primary
TMDS Type -- NONE
DDC Type -- VGA_DDC
(II) RADEON(0): Secondary:
Monitor -- NONE
Connector -- Proprietary
DAC Type -- TVDAC/ExtDAC
TMDS Type -- NONE
DDC Type -- NONE
...
(WW) RADEON(0): Failed to detect secondary monitor, MergedFB/Clone
mode disabled
...
(II) RADEON(0): Validating modes on Primary head ---------
(WW) RADEON(0): config file hsync range 15-64kHz not within DDC
hsync ranges.
(WW) RADEON(0): config file vrefresh range 50-85Hz not within DDC
vrefresh ranges.
(II) RADEON(0): Laptop: Using hsync range of 15.00-64.00 kHz
(II) RADEON(0): Laptop: Using vrefresh range of 50.00-85.00 Hz
(II) RADEON(0): Clock range: 20.00 to 350.00 MHz
...
(WW) RADEON(1): Only one monitor detected, Second screen will NOT be
created
...
(WW) RADEON(0): Option "CloneDisplay" is not used
(WW) RADEON(0): Option "CloneMode" is not used
(WW) RADEON(0): Option "CloneHSync" is not used
(WW) RADEON(0): Option "CloneVRefresh" is not used
Vielen Dank für die Mühe.
Gruß,
Björn Zachej
--
Verschlüsselte Mail erwünscht -- Encrypted mail welcome
GnuPG Key-ID: 0xF750C56AE3C4C731
Attachment:
signature.asc
Description: Digital signature