[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

LILO und Windows XP

Ich habe mir einen neuen Kernel unter Linux installiert und einen neuen Eintrag in der lilo.conf hinzugefügt. Da ich Windows XP habe benutze ich folgende Bootoption....Der Bootloader von Windows kommt als erstes...da kann ich auswählen ob ich Linux oder Windows laden will. Wenn ich Linux wähle startet er LILO. Damit das so funktioniert habe ich mit dem Kommando 'dd if=/dev/hda2 of=linux.bin bs=512 count=1' denBootsektor in der Datei linux.bin abgelegt. Diese habe ich dann in Windows auf C:\ kopiert. Von da aus greift der Windows Bootmanager drauf zu (in der boot.ini definiert). Das alles hat mir jemand einmal erklärt und es funktioniert halt......aber jetzt wo ich ein paar Einstellungen an LILO vorgenommen habe und ich alles genauso wie beschrieben gemacht habe scheint er die neue Konfiguration nicht zu verwenden - soll heißen er bringt immer noch das alte LILO beim booten. lilo habe ich natürlich nach der Konfiguration neugestartet. 

Hier noch meine lilo.conf

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt' (if you have created it), or   |
# | install a new kernel.  The computer will most likely fail to  |
# | boot if a kernel-image post-install script or you don't       |
# | remember to run `lilo'.                                       |
# |                                                               |
# +---------------------------------------------------------------+

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda2

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda2

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: text, bmp, and menu
# Look in lilo.conf(5) manpage for details
#
#install=menu

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=30

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
#message=/boot/bootmess.txt
#   prompt
#   delay=100
#   timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWTO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# If you used a serial console to install Debian, this option should be
# enabled by default.
# serial=

#
# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
    label=Linux
    read-only
#   restricted
#   alias=1

    initrd=/initrd.img

image=/vmlinuz
    append = "hdd=ide-scsi hdc=ide-scsi"
    label=Linux2
    read-only
#   restricted
#   alias=1

    initrd=/initrd.img

image=/vmlinuz.old
    label=LinuxOLD
    read-only
    optional
#   restricted
#   alias=2

    initrd=/initrd.img.old


image=/boot/vmlinuz-2.6.11-1-k7
    label=Linux.new
    read-only
#   restricted
#   alias=1

    initrd=/initrd.img


# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#   label=HURD
#   restricted
#   alias=3
#other=/dev/hda1
#   label=Windows
#   restricted
#   alias=2
Reply to: