Module und kernel 2.6
Hallo,
ich hab' einige Fragen zum Thema. Ich hab' sarge (ursprünglich woody) & kernel
2.6.7-1-k7.
Insmod scheint es nicht mehr zu geben, kann ich also rausschmeissen. Richtig?
Ich finde, ich hab' wahnsinnig viele Module geladen und möchte gerne wissen,
welche ich rausschmeissen kann:
Module Size Used by
via686a 19656 0
eeprom 7816 0
i2c_sensor 2944 2 via686a,eeprom
i2c_isa 2048 0
sg 38688 0
i2c_dev 10368 0
i2c_viapro 7116 0
i2c_core 24020 6
via686a,eeprom,i2c_sensor,i2c_isa,i2c_dev,i2c_viapro
usbnet 27905 1
lp 10948 0
autofs 17280 2
ipv6 253024 14
af_packet 22408 4
8139cp 20672 0
pci_hotplug 34352 0
via_agp 8768 1
mousedev 10444 2
tsdev 7360 0
psmouse 20232 0
floppy 60308 0
pcspkr 3688 0
evdev 9536 0
uhci_hcd 32592 0
agpgart 33960 1 via_agp
snd_ens1371 25252 3
snd_rawmidi 25408 1 snd_ens1371
snd_seq_device 8264 1 snd_rawmidi
snd_pcm_oss 54312 0
snd_mixer_oss 19904 1 snd_pcm_oss
snd_pcm 97508 4 snd_ens1371,snd_pcm_oss
snd_page_alloc 11720 1 snd_pcm
snd_timer 25540 1 snd_pcm
snd_ac97_codec 69572 1 snd_ens1371
snd 56932 12
snd_ens1371,snd_rawmidi,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_ac97_codec
soundcore 10400 1 snd
gameport 4736 1 snd_ens1371
nls_cp437 5760 2
sd_mod 21696 0
st 40028 0
dm_mod 44704 0
capability 4616 0
commoncap 7232 1 capability
ide_scsi 17348 1
osst 53144 0
multipath 8584 0
linear 5056 0
md 49416 2 multipath,linear
c_qcam 11992 0
sr_mod 17892 0
cdrom 39904 1 sr_mod
parport_pc 34944 2
bw_qcam 11432 0
videodev 9984 2 c_qcam,bw_qcam
parport 41544 4 lp,c_qcam,parport_pc,bw_qcam
aic7xxx 204588 0
scsi_mod 124556 7 sg,sd_mod,st,ide_scsi,osst,sr_mod,aic7xxx
8139too 26112 0
mii 5184 3 usbnet,8139cp,8139too
crc32 4352 3 usbnet,8139cp,8139too
ppp_synctty 9472 0
ppp_deflate 6336 0
zlib_deflate 22232 1 ppp_deflate
ppp_async 12288 0
ppp_generic 29908 3 ppp_synctty,ppp_deflate,ppp_async
slhc 7936 1 ppp_generic
usbkbd 7424 0
usbcore 113952 5 usbnet,uhci_hcd,usbkbd
rtc 12728 0
reiserfs 243184 3
isofs 35960 0
vfat 14656 1
fat 46656 1 vfat
ext3 126760 0
jbd 61592 1 ext3
mbcache 9220 1 ext3
ide_disk 19264 6
ide_generic 1472 0
via82cxxx 14044 1
ide_core 141592 4 ide_scsi,ide_disk,ide_generic,via82cxxx
unix 28528 611
font 8448 0
vesafb 6688 0
cfbcopyarea 3776 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3712 1 vesafb
Zu meiner Hardware:
- Drucker
- Scanner Agfa Snapscan 1236S
- ura lt scsi CD-Brenner
- Onstream Bandlaufwerk
- Webcam Logitech Quickcam pro 4000 (war beim Systemstart nicht mit dem
Rechner verbunden, da ich damit noch Schwierigkiten habe).
Auch habe ich win installiert, daher fat und vfat. Ich benutze sonst nur
reiserfs, daher habe ich mit modconf ext2 und ext3 rausgeworfen. Zu meinem
Erstaunen führt lsmod sie aber immer noch auf. Wie dieses?
Ansonsten beutze ich kde und alsa.
Ich gab' auch gleich mal dmesg durch. Ist zwar lang, aber IMHO nützlich.
Linux version 2.6.7-1-k7 (dilinger@toaster.hq.voxel.net) (gcc version 3.3.4
(Debian 1:3.3.4-2)) #1 Thu Jul 8 06:45:35 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Built 1 zonelists
Kernel command line: root=/dev/hda6 read-only acpi=off
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1667.442 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 252104k/262080k available (1500k kernel code, 9264k reserved, 668k
data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3276.80 BogoMIPS
Security Scaffold v1.0.0 initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1666.0445 MHz.
..... host bus clock speed is 266.0631 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4624k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f71d0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x5f74, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
spurious 8259A interrupt: IRQ7.
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4624 blocks [1 disk] into ram disk... | / - \ | / - \ | / - \
| / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
\ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | /
- \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \
| / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
\ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | /
- \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \
| / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
\ | / - \ | done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L060AVER07-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
hdd: OnStream DI-30, ATAPI TAPE drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 120103200 sectors (61492 MB) w/1916KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
VFS: Can't find ext3 filesystem on dev hda6.
VFS: Can't find ext2 filesystem on dev hda6.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda6.
Unable to identify CD-ROM format.
ReiserFS: hda6: found reiserfs format "3.6" with standard journal
ReiserFS: hda6: using ordered data mode
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda6: checking transaction log (hda6)
ReiserFS: hda6: Using r5 hash to sort names
Adding 401584k swap on /dev/hda8. Priority:-1 extents:1
Real Time Clock Driver v1.12
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
8139too Fast Ethernet driver 0.9.27
PCI: Found IRQ 9 for device 0000:00:0a.0
eth0: RealTek RTL8139 at 0xd000, 00:50:fc:23:16:43, IRQ 9
eth0: Identified 8139 chip type 'RTL-8139C'
SCSI subsystem initialized
PCI: Found IRQ 11 for device 0000:00:0c.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 SCSI adapter>
aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
(scsi0:A:5): 10.000MB/s transfers (10.000MHz, offset 15)
Vendor: TEAC Model: CD-R56S Rev: 1.0P
Type: CD-ROM ANSI SCSI revision: 02
Linux video capture interface: v1.00
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport_pc: Via 686A parallel port: io=0x378
parport0 (bw-qcam): use data_reverse for this!
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
Connectix Quickcam on parport0
videodev: "Connectix Quickcam" has no release callback. Please fix your driver
for proper sysfs support, see http://lwn.net/Articles/36850/
Colour QuickCam for Video4Linux v0.05
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: linear personality registered as nr 1
md: multipath personality registered as nr 7
osst :I: Tape driver with OnStream support version 0.99.1
osst :I: $Id: osst.c,v 1.70 2003/12/23 14:22:12 wriede Exp $
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as
device
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-M1212 Rev: 1R14
Type: CD-ROM ANSI SCSI revision: 02
sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: OnStream Model: DI-30 Rev: 1.05
Type: Sequential-Access ANSI SCSI revision: 02
osst :I: Attached OnStream DI-30 tape at scsi2, channel 0, id 0, lun 0 as
osst0
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
st: Version 20040403, fixed bufsize 32768, s/g segs 256
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
PCI: Found IRQ 10 for device 0000:00:0f.0
PCI: Sharing IRQ 10 with 0000:00:07.3
PCI: Sharing IRQ 10 with 0000:00:07.2
Linux agpgart interface v0.100 (c) Dave Jones
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 10 for device 0000:00:07.2
PCI: Sharing IRQ 10 with 0000:00:07.3
PCI: Sharing IRQ 10 with 0000:00:0f.0
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:07.3
PCI: Sharing IRQ 10 with 0000:00:07.2
PCI: Sharing IRQ 10 with 0000:00:0f.0
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:07.3: irq 10, io base 0000d800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
input: PC Speaker
inserting floppy driver for 2.6.7-1-k7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
mice: PS/2 mouse device common for all mice
agpgart: Detected VIA KLE133 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f17c0(lo)
IPv6 over IPv4 tunneling driver
lp0: using parport0 (polling).
apm: BIOS not found.
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
apm: BIOS not found.
apm: BIOS not found.
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
apm: BIOS not found.
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
apm: BIOS not found.
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
eth0: link down
usb 1-2: new full speed USB device using address 2
usb%d: unregister usbnet usb-0000:00:07.2-2, CDC Ethernet Device
unregister_netdevice: device usb%d/cce0cc00 never was registered
Unable to handle kernel paging request at virtual address 20207069
printing eip:
d0d794ee
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: usbnet lp autofs ipv6 af_packet 8139cp pci_hotplug via_agp
mousedev tsdev psmouse floppy pcspkr evdev uhci_hcd agpgart snd_ens1371
snd_rawmidi snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm snd_page_alloc
snd_timer snd_ac97_codec snd soundcore gameport nls_cp437 sd_mod st dm_mod
capability commoncap ide_scsi osst multipath linear md c_qcam sr_mod cdrom
parport_pc bw_qcam videodev parport aic7xxx scsi_mod 8139too mii crc32
ppp_synctty ppp_deflate zlib_deflate ppp_async ppp_generic slhc usbkbd
usbcore rtc reiserfs isofs vfat fat ext2 ext3 jbd mbcache ide_disk
ide_generic via82cxxx ide_core unix font vesafb cfbcopyarea cfbimgblt
cfbfillrect
CPU: 0
EIP: 0060:[<d0d794ee>] Not tainted
EFLAGS: 00010282 (2.6.7-1-k7)
EIP is at usbnet_probe+0x3ce/0x400 [usbnet]
eax: 20207065 ebx: c1247a00 ecx: 00000001 edx: 00000001
esi: d0d79dd2 edi: cce0cc06 ebp: cce0cc00 esp: c20bfebc
ds: 007b es: 007b ss: 0068
Process modprobe (pid: 9968, threadinfo=c20be000 task=c9898ed0)
Stack: c1247a00 cfe4fcb8 00000006 c20bfefc c018e679 c714a400 c714a4cc ffffffea
d0d79720 c38c8ae0 d0d7c9c0 cfe4fcb8 ffffffed d0d7c9e0 d0a3a07a cfe4fcb8
d0d79be4 d0d7c9e0 cfe4fcc8 ffffffed c01ee40f cfe4fcc8 d0d7c9e0 cfe4fcd0
Call Trace:
[<c018e679>] create_dir+0x99/0xa0
[<d0a3a07a>] usb_probe_interface+0x5a/0x60 [usbcore]
[<c01ee40f>] bus_match+0x3f/0x70
[<c01ee539>] driver_attach+0x59/0x90
[<c01ee7e1>] bus_add_driver+0x91/0xb0
[<c01eec9f>] driver_register+0x2f/0x40
[<d0a3a13f>] usb_register+0x3f/0xa0 [usbcore]
[<c01d0f75>] get_random_bytes+0x45/0x60
[<d0c9e035>] usbnet_init+0x35/0x39 [usbnet]
[<c0131dff>] sys_init_module+0xff/0x210
[<c0106087>] syscall_call+0x7/0xb
Code: f6 40 04 20 0f 84 3f fe ff ff f6 85 8c 00 00 00 02 0f 85 32
<6>usb 1-2: USB disconnect, address 2
eth0: link up, 10Mbps, full-duplex, lpa 0x4061
eth0: no IPv6 routers present
i2c /dev entries driver
Attached scsi generic sg0 at scsi0, channel 0, id 5, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 1
tschüs
Klaus
Reply to: