Re: Ext3-Wiederherstellung
Hallo,
> Suche mal nach smart-tools für deine HD (Hersteller oder
> smartmontools[1]) und
Ich habe jetzt einmal den Testlauf durchlaufen lassen, folgende Ausgaben
bekomme ich:
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y120L0
Serial Number: Y40BF74E
Firmware Version: YAR41VW0
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: 9,minutes
Local Time is: Sun Apr 27 16:58:28 2003 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Off-line data collection status: (0x80) Offline data collection activity
was
never started.
Auto Off-line Data Collection: Enabled.
Self-test execution status: ( 118) The previous self-test completed
having
the read element of the test failed.
Total time to complete off-line
data collection: ( 242) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Automatic timer ON/OFF support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 63) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 252 252 063 Pre-fail -
0
4 Start_Stop_Count 0x0032 253 253 000 Old_age -
0
5 Reallocated_Sector_Ct 0x0033 247 247 063 Pre-fail -
67
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail -
0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age -
0
8 Seek_Time_Performance 0x0027 248 248 187 Pre-fail -
24302
9 Power_On_Hours 0x0032 253 253 000 Old_age -
2718
10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail -
0
11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail -
0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age -
33
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age -
0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age -
0
194 Temperature_Celsius 0x0032 253 253 000 Old_age -
41
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age -
3889
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age -
0
197 Current_Pending_Sector 0x0008 247 247 000 Old_age -
67
198 Offline_Uncorrectable 0x0008 252 252 000 Old_age -
1
199 UDMA_CRC_Error_Count 0x0008 253 253 000 Old_age -
0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age -
0
201 Unknown_Attribute 0x000a 253 252 000 Old_age -
3
202 Unknown_Attribute 0x000a 253 252 000 Old_age -
0
203 Unknown_Attribute 0x000b 253 252 180 Pre-fail -
1
204 Unknown_Attribute 0x000a 253 252 000 Old_age -
0
205 Unknown_Attribute 0x000a 253 252 000 Old_age -
0
207 Unknown_Attribute 0x002a 252 252 000 Old_age -
0
208 Unknown_Attribute 0x002a 252 252 000 Old_age -
0
209 Unknown_Attribute 0x0024 253 253 000 Old_age -
0
99 Unknown_Attribute 0x0004 253 253 000 Old_age -
0
100 Unknown_Attribute 0x0004 253 253 000 Old_age -
0
101 Unknown_Attribute 0x0004 253 253 000 Old_age -
0
SMART Error Log Version: 1
Warning: ATA error count 1031 inconsistent with error log pointer 5
ATA Error Count: 1031 (device log contains only the most recent five
errors)
DCR = Device Control Register
FR = Features Register
SC = Sector Count Register
SN = Sector Number Register
CL = Cylinder Low Register
CH = Cylinder High Register
D/H = Device/Head Register
CR = Content written to Command Register
ER = Error register
STA = Status register
Timestamp is seconds since the previous disk power-on.
Note: timestamp "wraps" after 2^32 msec = 49.710 days.
Error 1031 occurred at disk power-on lifetime: 41 hours
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER:40 SC:08 SN:c0 CL:26 CH:84 D/H:e8 ST:59
Sequence of commands leading to the command that caused the error were:
DCR FR SC SN CL CH D/H CR Timestamp
08 00 18 b1 26 84 e8 20 172414.288
08 00 18 f9 16 13 e9 20 172414.288
08 00 18 f1 f6 12 e9 20 172414.288
08 00 18 e9 d6 12 e9 20 172414.272
08 00 18 e1 b6 12 e9 20 172414.272
Error 1030 occurred at disk power-on lifetime: 41 hours
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER:40 SC:08 SN:c0 CL:26 CH:10 D/H:e7 ST:59
Sequence of commands leading to the command that caused the error were:
DCR FR SC SN CL CH D/H CR Timestamp
08 00 18 b1 26 10 e7 20 172342.704
08 00 18 39 5f 02 e7 20 172342.704
08 00 18 31 3f 02 e7 20 172342.704
08 00 18 29 1f 02 e7 20 172342.688
08 00 18 21 ff 01 e7 20 172342.688
Error 1029 occurred at disk power-on lifetime: 41 hours
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER:40 SC:08 SN:08 CL:fb CH:59 D/H:e0 ST:59
Sequence of commands leading to the command that caused the error were:
DCR FR SC SN CL CH D/H CR Timestamp
08 00 10 01 fb 59 e0 20 172123.328
08 00 38 c9 fa 59 e0 20 172123.328
08 00 08 c1 fa 59 e0 20 172123.328
08 00 18 81 fa 59 e0 20 172123.312
08 00 08 51 f8 59 e0 20 172123.312
Error 1028 occurred at disk power-on lifetime: 41 hours
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER:40 SC:08 SN:c1 CL:26 CH:20 D/H:e8 ST:59
Sequence of commands leading to the command that caused the error were:
DCR FR SC SN CL CH D/H CR Timestamp
08 00 08 c1 26 20 e8 20 172025.824
08 00 08 c1 26 c0 e7 20 172025.808
08 00 08 c1 26 dc ec 20 172025.792
08 00 08 c1 26 ac ec 20 172025.792
08 00 08 c1 26 a8 eb 20 172025.776
Error 1027 occurred at disk power-on lifetime: 41 hours
When the command that caused the error occurred, the device was in an
unknown state.
After command completion occurred, registers were:
ER:40 SC:08 SN:c1 CL:26 CH:20 D/H:e8 ST:59
Sequence of commands leading to the command that caused the error were:
DCR FR SC SN CL CH D/H CR Timestamp
08 00 08 c1 26 20 e8 20 172024.704
08 00 08 c1 26 b8 eb 20 172024.688
08 00 08 c1 26 bc e3 20 172024.688
08 00 08 c1 36 b4 e3 20 172024.672
08 00 08 c1 26 b4 e3 20 172024.672
SMART Self-test log, version number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short off-line Completed: read failure 60% 42
0x0059fb09
# 2 Extended off-line Completed: read failure 40% 42
0x0059fb09
# 3 Extended off-line Completed: read failure 40% 42
0x0059fb09
Da scheint ja einiges kaputt zu sein, weiss jemand Rat? oder würdet ihr
die Partition am Besten gerade neu formatieren oder gibts gute
Reparatur-Tools.
Danke und Grüsse Patrick
Reply to: