Re: TV-Karte die 3.
Am Freitag, 7. März 2003 15:14 schrieben Sie:
> Viell. guckst du dir auch mal die Anzeige des Befehls:
>
> dmesg | grep -C3 bttv
>
> an. Das ist eine Ausgabe von den Bootmeldungen.
>
> Bei mir:
>
>
> thomas@gamma:~$ dmesg | grep -C3 bttv
> NTFS driver v1.1.22 [Flags: R/O MODULE]
> i2c-core.o: i2c core module
> i2c-algo-bit.o: i2c bit algorithm module
> bttv: driver version 0.7.96 loaded
> bttv: using 4 buffers with 2080k (8320k total) for capture
> bttv: Host bridge is Intel Corp. 82845 845 (Brookdale) Chipset Host
> Bridge
> bttv: Bt8xx card found (0).
> PCI: Enabling device 02:09.0 (0004 -> 0006)
> PCI: Found IRQ 5 for device 02:09.0
> PCI: Sharing IRQ 5 with 02:03.0
> PCI: Sharing IRQ 5 with 02:09.1
> bttv0: Bt878 (rev 17) at 02:09.0, irq: 5, latency: 32, mmio:
> 0xf5000000
> bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is
> 0070:13eb
> bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected]
> bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
> i2c-core.o: adapter bt848 #0 registered as adapter 0.
> bttv0: Hauppauge eeprom: model=44354, tuner=Temic 4009FR5 (20),
> radio=yes
> bttv0: using tuner=20
> bttv0: i2c: checking for MSP34xx @ 0x80... found
> i2c-core.o: driver i2c msp3400 driver registered.
> msp34xx: init: chip=MSP3415G-B8, has NICAM support
> msp3410: daemon started
> bttv0: i2c attach [client=MSP3415G-B8,ok]
> i2c-core.o: client [MSP3415G-B8] registered to adapter [bt848 #0](pos.
> 0).
> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> tvaudio: TV audio decoder + audio/video mux driver
> tvaudio: known chips:
> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c5
>4 (PV951)
> i2c-core.o: driver generic i2c audio driver registered.
> i2c-core.o: driver i2c TV tuner driver registered.
> tuner: probing bt848 #0 i2c adapter [id=0x10005]
> tuner: chip found @ 0xc2
> bttv0: i2c attach [client=Temic PAL_BG (4009 FR5) or PAL_I,ok]
> i2c-core.o: client [Temic PAL_BG (4009 FR5) or PAL_I] registered to
> adapter [bt848 #0](pos. 1).
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: registered device radio0
> i2c-algo-pcf.o: i2c pcf8584 algorithm module
> i2c-dev.o: i2c /dev entries driver module
> i2c-core.o: driver i2c-dev dummy driver registered.
>
>
> Thomas
Hi, meines sagt folgendes, da sieht man gleicht, er erkennt da irgendwas
nicht oder falsch, nur was?
LordKelvinAthlonXP:/usr/doc# dmesg|grep -C3 bttv
i2c-core.o: driver i2c TV tuner driver registered.
i2c-core.o: driver i2c msp3400 driver registered.
Linux video capture interface: v1.00
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Silicon Integrated Systems [SiS] 735 Host
bttv: Bt8xx card found (0).
PCI: Found IRQ 11 for device 00:0f.0
PCI: Sharing IRQ 11 with 00:02.2
PCI: Sharing IRQ 11 with 00:0f.1
bttv0: Bt878 (rev 17) at 00:0f.0, irq: 11, latency: 64, memory: 0xcddfe000
bttv0: using: BT878( *** UNKNOWN/GENERIC **) [card=0,autodetected]
tuner: chip found @ 0xc2
bttv0: i2c attach [client=(unset),ok]
i2c-core.o: client [(unset)] registered to adapter [bt848 #0](pos. 0).
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00e) is not claimed by any active
drive
Ich hoffe, meine Karte wird _überhaupt_ unterstützt.
--
Markus Hansen
markus.hansen@tu-harburg.de
Reply to: