[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Carte TV ASUS MyCinema P7131 Hybrid

Bonsoir !

J'ai fait l'acquisition de la chose sus-nommée et ça marche pas.
Je m'explique la carte est détectée au démarrage, les modules sont
chargés, etc ....
 #dmesg 

saa7133[0]: found at 0000:02:0a.0, rev: 209, irq: 22, latency: 64, mmio:
0xfeaff000
saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid
[card=112,insmod option]
saa7133[0]: board init: gpio is 40000
saa7133[0]: gpio: mode=0x0000000 in=0x0040000 out=0x0000000 [pre-init]
input: saa7134 IR (ASUSTeK P7131 Hybri as
/devices/pci0000:00/0000:00:1e.0/0000:02:0a.0/input/input5
saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2
92
saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff
ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c scan: found device @ 0x10  [???]
saa7133[0]: i2c scan: found device @ 0x96  [???]
saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
tuner' 1-004b: chip found @ 0x96 (saa7133[0])
tda8290 1-004b: setting tuner address to 61
tda8290 1-004b: type set to tda8290+75a
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision 29 -- ok


puis plus loin 


saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0200000 [Radio]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0040000 out=0x0000000 [Television]

mais si je lance tvtime il m'annonce " pas de signal" 
    si je lance dvbutils j'ai droit à "tuning failed"

j'aisuivi un How-to spécifique saa7134 et en particulier cette partie :

ASUS MyCinema P7131 Hybrid

    * 00:0c.0 Multimedia controller: Philips Semiconductors SAA7133
    * Video Broadcast Decoder (rev d1)
    * saa7134 card=78 tuner=54 # for analog signal 

    * Troubleshooting on card [1043:4876]
    * In /usr/src/linux/drivers/media/video/saa7134/saa7134-dvb.c, line
    * 873, struct tda1004x_config philips_tiger_config
    * change the entry
    * .request_firmware = NULL,
    * to
    * .request_firmware = philips_tu1216_request_firmware,
    * run /usr/src/linux/Documentation/dvb/get_dvb_firmware and copy the
    * dvb-fe-tda10046.fw to /lib/firmware
    * modprobe saa7134 card=78 gpio_tracking=1
    * see http://www.spinics.net/lists/vfl/msg27672.html
    * STOP PRESS - the Mercurial version "emerge v4l-dvb-hg" gives the
    * card a proper card number of 112.
    * The card can then be brought up with "modprobe saa7134 card=112
    * tuner=54 gpio_tracking=1 i2c_scan=1". You may also need to
    * modprobe saa7134-dvb and saa7134-alsa. This works now but may not
    * continue to do so. 

Quelqu'un a sûrement réussi à faire fonctionner cette carte ...
et  à obtenir un signal ....

Merci


mahashakti89
Reply to: