Soucis avec sane et CanoScan LiDE25
Bonjour chère liste,
Je tourne actuellement sous une Debian etch (2.6.18-5-686 bien mise à
jour et toute fraiche net-installée).
J'ai acheté le scanner CanoScan LiDE25 (bien supporté par sane, selon
leur site web).
J'ai suivi quelques explicatifs trouvés grâce à mon ami google.
J'ai donc fait un petit :
sane-find-scanner
Qui me retourne :
[snip]
found USB scanner (vendor=0x04a9 [Canon], product=0x2220 [CanoScan],
chip=LM9832/3) at libusb:001:006
[snip]
Tout content de moi, j'ai donc tenté de configurer Sane avec ces
informations :
/etc/sane.d/canon.conf
#canon.conf
/dev/scanner
#/proc/bus/usb/001/005
#/dev/sg0
usb 0x04a9 0x2220
Et dans le doute j'ai aussi configuré Sane avec plustek.conf (j'ai peut
être fait un bêtise ?).
/etc/sane.d/plustek.conf
[usb]
0x04a9 0x2220
libusb:001:005
Toutes les autres autres options de ce plustek.conf sont laissées par
défaut.
Et là commencent les soucis : xsane plante au lancement (ne répond tout
simplement pas).
J'ai donc fait un petit : "scanimage -L" ... qui plante tout autant.
Sur ce, j'ai cherché à en savoir plus, j'ai fait donc la commande
suivante :
#export SANE_DEBUG_PLUSTEK=255 ; scanimage -L
Puisque le retour de cette commande est particulièrement longue, je vous
la metterai au bout de ce mail ...
Plus haut, dans canon.conf, il y a marqué que mon scanner serait branché
sous /dev/scanner.
Un petit
ls /dev/scanner
Me retourne ceci :
ls: /dev/scanner: Aucun fichier ou répertoire de ce type
L'erreur ne proviendrait pas de là ?
Enfin, j'ai même fait un petit : tail -f /var/log/syslog
qui me donne :
Nov 2 23:34:10 staff kernel: usb 1-1: USB disconnect, address 4
Nov 2 23:34:13 staff kernel: usb 1-1: new full speed USB device using
uhci_hcd and address 6
Nov 2 23:34:13 staff kernel: usb 1-1: configuration #1 chosen from 1
choice
quand je déconnecte et reconnecte le scanner ...
Qu'en pensez vous ?
Comment avez vous configuré vos fichiers sane pour votre scanner
préféré ?
canon.conf et plustek.conf doivent tout deux être configurés ?! Je ne
pense pas, ça serait quelque part illogique, mais je suis un peu
perdu ...
Merci pour vos conseils !
Voici le scanimage -L en mode Debug (qui ne retourne rien d'autre... et
reste à tourner dans le vide ...) :
# export SANE_DEBUG_PLUSTEK=255 ; scanimage -L
[sanei_debug] Setting debug level of plustek to 255.
[plustek] Plustek backend V0.51-12, part of sane-backends 1.0.18
[plustek] Retrieving all supported and conntected devices
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0013
[plustek] Checking for 0x07b3-0x0011
[plustek] Checking for 0x07b3-0x0010
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0015
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0016
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0017
[plustek] Checking for 0x07b3-0x0007
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x000f
[plustek] Checking for 0x07b3-0x0005
[plustek] Checking for 0x07b3-0x0014
[plustek] Checking for 0x07b3-0x0012
[plustek] Checking for 0x0400-0x1000
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0400-0x1001
[plustek] Checking for 0x0458-0x2007
[plustek] Checking for 0x0458-0x2008
[plustek] Checking for 0x0458-0x2009
[plustek] Checking for 0x0458-0x2013
[plustek] Checking for 0x0458-0x2015
[plustek] Checking for 0x0458-0x2016
[plustek] Checking for 0x03f0-0x0505
[plustek] Checking for 0x03f0-0x0605
[plustek] Checking for 0x04b8-0x010f
[plustek] Checking for 0x04b8-0x011d
[plustek] Checking for 0x1606-0x0050
[plustek] Checking for 0x1606-0x0060
[plustek] Checking for 0x1606-0x0160
[plustek] Checking for 0x049f-0x001a
[plustek] Checking for 0x04a9-0x2206
[plustek] Checking for 0x04a9-0x2207
[plustek] Checking for 0x04a9-0x2208
[plustek] Checking for 0x04a9-0x220d
[plustek] Checking for 0x04a9-0x220e
[plustek] Checking for 0x04a9-0x2220
[plustek] Checking for 0x0a82-0x6620
[plustek] Available and supported devices:
[plustek] Device: >libusb:001:006< - 0x04a9x0x2220
[plustek] ># Plustek-SANE Backend configuration file<
[plustek] ># For use with LM9831/2/3 based USB scanners<
[plustek] >#<
[plustek] ><
[plustek] ># each device needs at least two lines:<
[plustek] ># - [usb] vendor-ID and product-ID<
[plustek] ># - device devicename<
[plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device /dev/usbscanner<
[plustek] ># or<
[plustek] ># device libusb:bbb:ddd<
[plustek] ># where bbb is the busnumber and ddd the device number<
[plustek] ># make sure that your user has access
to /proc/bus/usb/bbb/ddd<
[plustek] >#<
[plustek] ># additionally you can specify some options<
[plustek] ># warmup, lOffOnEnd, lampOff<
[plustek] >#<
[plustek] ># For autodetection use<
[plustek] ># [usb]<
[plustek] ># device /dev/usbscanner<
[plustek] >#<
[plustek] ># or simply<
[plustek] ># [usb]<
[plustek] >#<
[plustek] ># or if you want a specific device but you have no idea about
the<
[plustek] ># device node or you use libusb, simply set vendor- and
product-ID<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device auto<
[plustek] >#<
[plustek] ># NOTE: autodetection is safe, as it uses the info it got<
[plustek] ># from the USB subsystem. If you're not using the<
[plustek] ># autodetection, you MUST have attached that device<
[plustek] ># at your USB-port, that you have specified...<
[plustek] >#<
[plustek] ><
[plustek] >[usb]<
[plustek] next device uses autodetection
[plustek] ... next device
[plustek] >0x04a9 0x2220<
[plustek] ignoring >0x04a9 0x2220<
[plustek] >libusb:001:006<
[plustek] ignoring >libusb:001:006<
[plustek] ><
[plustek] >#<
[plustek] ># options for the previous USB entry<
[plustek] >#<
[plustek] ># switch lamp off after xxx secs, 0 disables the feature<
[plustek] ># (can also be set via frontend)<
[plustek] >option lampOff 300<
[plustek] Decoding option >lampOff<
[plustek] ><
[plustek] ># warmup period in seconds, 0 means no warmup, -1 means
auto-warmup<
[plustek] ># (can also be set via frontend)<
[plustek] >option warmup -1<
[plustek] Decoding option >warmup<
[plustek] ><
[plustek] ># 0 means leave lamp-status untouched, not 0 means switch
off<
[plustek] ># on sane_close<
[plustek] ># (can also be set via frontend)<
[plustek] >option lOffOnEnd 1<
[plustek] Decoding option >lOffOnEnd<
[plustek] ><
[plustek] >#<
[plustek] ># options to tweak the image start-position<
[plustek] ># (WARNING: there's no internal range check!!!)<
[plustek] >#<
[plustek] ># for the normal scan area<
[plustek] >#<
[plustek] >option posOffX 0<
[plustek] Decoding option >posOffX<
[plustek] >option posOffY 0<
[plustek] Decoding option >posOffY<
[plustek] ><
[plustek] ># for transparencies<
[plustek] >option tpaOffX 0<
[plustek] Decoding option >tpaOffX<
[plustek] >option tpaOffY 0<
[plustek] Decoding option >tpaOffY<
[plustek] ><
[plustek] ># for negatives<
[plustek] >option negOffX 0<
[plustek] Decoding option >negOffX<
[plustek] >option negOffY 0<
[plustek] Decoding option >negOffY<
[plustek] ><
[plustek] >#<
[plustek] ># for setting the calibration strip position<
[plustek] ># (WARNING: there's no internal range check!!!)<
[plustek] ># -1 means use built in<
[plustek] ># (can also be set via frontend)<
[plustek] >option posShadingY -1<
[plustek] Decoding option >posShadingY<
[plustek] >option tpaShadingY -1<
[plustek] Decoding option >tpaShadingY<
[plustek] >option negShadingY -1<
[plustek] Decoding option >negShadingY<
[plustek] ><
[plustek] >#<
[plustek] ># to invert the negatives, 0 disables the feature<
[plustek] >#<
[plustek] >option invertNegatives 0<
[plustek] Decoding option >invertNegatives<
[plustek] ><
[plustek] >#<
[plustek] ># to disable the internal sensor speedup function,<
[plustek] ># 1 disables the feature<
[plustek] >#<
[plustek] >option disableSpeedup 0<
[plustek] Decoding option >disableSpeedup<
[plustek] ><
[plustek] >#<
[plustek] ># to save/restore coarse calibration data<
[plustek] ># (can also be set via frontend)<
[plustek] >option cacheCalData 0<
[plustek] Decoding option >cacheCalData<
[plustek] ><
[plustek] >#<
[plustek] ># use alternate calibration routines<
[plustek] >#<
[plustek] >option altCalibration 0<
[plustek] Decoding option >altCalibration<
[plustek] ><
[plustek] >#<
[plustek] ># for skipping whole calibration step<
[plustek] >#<
[plustek] >option skipCalibration 0<
[plustek] Decoding option >skipCalibration<
[plustek] ><
[plustek] >#<
[plustek] ># for skipping entire fine calibration step<
[plustek] ># coarse calibration is done<
[plustek] >#<
[plustek] >option skipFine 0<
[plustek] Decoding option >skipFine<
[plustek] ><
[plustek] >#<
[plustek] ># discard the result of the fine white calibration<
[plustek] >#<
[plustek] >option skipFineWhite 0<
[plustek] Decoding option >skipFineWhite<
[plustek] ><
[plustek] ># for replacing the gain values found during coarse<
[plustek] ># calibration<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_gain -1<
[plustek] Decoding option >red_gain<
[plustek] >option green_gain -1<
[plustek] Decoding option >green_gain<
[plustek] >option blue_gain -1<
[plustek] Decoding option >blue_gain<
[plustek] ><
[plustek] ># for replacing the offset values found during coarse<
[plustek] ># calibration<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_offset -1<
[plustek] Decoding option >red_offset<
[plustek] >option green_offset -1<
[plustek] Decoding option >green_offset<
[plustek] >option blue_offset -1<
[plustek] Decoding option >blue_offset<
[plustek] ><
[plustek] >#<
[plustek] ># for replacing the default lampoff settings, this<
[plustek] ># works only for CIS devices like CanoScan LiDE20<
[plustek] ># (can also be set via frontend)<
[plustek] >option red_lampoff -1<
[plustek] Decoding option >red_lampoff<
[plustek] >option green_lampoff -1<
[plustek] Decoding option >green_lampoff<
[plustek] >option blue_lampoff -1<
[plustek] Decoding option >blue_lampoff<
[plustek] ><
[plustek] >#<
[plustek] ># for adjusting the default gamma values<
[plustek] ># (can also be set via frontend)<
[plustek] >option redGamma 1.0<
[plustek] Decoding option >redGamma<
[plustek] >option greenGamma 1.0<
[plustek] Decoding option >greenGamma<
[plustek] >option blueGamma 1.0<
[plustek] Decoding option >blueGamma<
[plustek] >option grayGamma 1.0<
[plustek] Decoding option >grayGamma<
[plustek] ><
[plustek] >#<
[plustek] ># to enable TPA (EPSON or UMAX, if autodetection fails)<
[plustek] ># 0 means default behaviour as specified in the internal
tables<
[plustek] ># 1 means enable (needed for UMAX 3450)<
[plustek] >option enableTPA 0<
[plustek] Decoding option >enableTPA<
[plustek] ><
[plustek] >#<
[plustek] ># model override functionality, currently only available for<
[plustek] ># Mustek devices, using NSCs' vendor ID: 0x0400 and<
[plustek] ># also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)<
[plustek] >#<
[plustek] ># mov/PID | 0x1000 | 0x1001<
[plustek] ># ---------------------------------------<
[plustek] ># 0 (default)| BearPaw1200 | BearPaw 2400<
[plustek] ># 1 | ignored | BearPaw 1200<
[plustek] >#<
[plustek] >option mov 0<
[plustek] Decoding option >mov<
[plustek] ><
[plustek] >#<
[plustek] ># and of course the device-name<
[plustek] >#<
[plustek] ># device /dev/usbscanner<
[plustek] >device auto<
[plustek] Decoding device name >auto<
[plustek] ><
[plustek] >#<
[plustek] ># to define a new device, start with a new section:<
[plustek] ># [usb]<
[plustek] >#<
[plustek] attach (auto, 0xbfc301ac, (nil))
[plustek] Device configuration:
[plustek] device name : >auto<
[plustek] USB-ID : ><
[plustek] model ovr. : 0
[plustek] warmup : -1s
[plustek] lampOff : 300
[plustek] lampOffOnEnd : yes
[plustek] cacheCalData : no
[plustek] altCalibrate : no
[plustek] skipCalibr. : no
[plustek] skipFine : no
[plustek] skipFineWhite: no
[plustek] invertNegs. : no
[plustek] dis.Speedup : no
[plustek] pos_x : 0
[plustek] pos_y : 0
[plustek] pos_shading_y: -1
[plustek] neg_x : 0
[plustek] neg_y : 0
[plustek] neg_shading_y: -1
[plustek] tpa_x : 0
[plustek] tpa_y : 0
[plustek] tpa_shading_y: -1
[plustek] red gain : -1
[plustek] green gain : -1
[plustek] blue gain : -1
[plustek] red offset : -1
[plustek] green offset : -1
[plustek] blue offset : -1
[plustek] red lampoff : -1
[plustek] green lampoff: -1
[plustek] blue lampoff : -1
[plustek] red Gamma : 1.00
[plustek] green Gamma : 1.00
[plustek] blue Gamma : 1.00
[plustek] gray Gamma : 1.00
[plustek] ---------------------
[plustek] usbDev_open(auto,) - 0x8074c18
[plustek] Vendor ID=0x04A9, Product ID=0x2220
[plustek] usbio_DetectLM983x
[plustek] usbio_DetectLM983x: found LM9832/3
[plustek] Detected vendor & product ID: 0x04A9-0x2220
[plustek] Device description for >0x04A9-0x2220< found.
[plustek] usb_initDev(43,0x04a9,-1)
[plustek] Device WAF : 0x00000002
[plustek] Transferrate: 1000000 Bytes/s
[plustek] Device Flags: 0x00000000
[plustek] Vendor adjusted to: >Canon<
[plustek] LAMP-STATUS: 0x00000000
[plustek] RESETTING REGISTERS(-1) - 0x80
[plustek] SETTING THE MISC I/Os
[plustek] MISC I/O after RESET: 0x66, 0x16, 0x91
[plustek] Calibration file-names set to:
[plustek] >/root/.sane/Canon-LiDE25-coarse.cal<
[plustek] >/root/.sane/Canon-LiDE25-fine.cal<
[plustek] usb_SetScanParameters()
[plustek] * HDPI: 8.000
[plustek] * XDPI=150, HDPI=8.000
[plustek] * YDPI=150, MinDPIY=75
[plustek] * DataPixelStart=127, LineEnd=127
[plustek] * DataPixelStart=128, LineEnd=128 (ADJ)
[plustek] >> End-Start=0, HDPI=8.00
[plustek] * Full Steps to Skip at Start = 0x0000
[plustek] * StepSize(Preset) = 148 (0x0094)
[plustek] * Scan calculations...
[plustek] * LineLength=10565, LineRateColor=3
[plustek] * Stepsize = 993, 0x46=0x03 0x47=0xe1
[plustek] * DPD =810 (0x032a)
[plustek] * DPD =30885 (0x78a5), step size=993, steps2rev=32
[plustek] * llen=10565, lineRateColor=3, qtcnt=8, hfcnt=8
[plustek] usb_GetMCLKDivider()
[plustek] usb_GetMCLKDiv()
[plustek] - lower mclkdiv limit=2.500000
[plustek] - upper mclkdiv limit=32.500000
[plustek] - hdpi = 8.000
[plustek] - pixelbits = 8
[plustek] - pixelsperline = 0
[plustek] - linelen = 10565
[plustek] - transferrate = 1000000
[plustek] - MCLK Divider = 0
[plustek] - Current MCLK Divider = 2
[plustek] * Integration Time Adjust = 0 (HDPI=8.000,MCLKD=4.000)
[plustek] * Setting GreenPWMDutyCycleHigh
[plustek] * Current MCLK Divider = 4.000000
[plustek] * MOTOR-Settings: PWM=0x08, PWM_DUTY=0x1f
[plustek] * FFStepSize = 416, [0x48] = 0x01, [0x49] = 0xa0
[plustek] * PhyBytes = 6
[plustek] * PhyLines = 3217226988
[plustek] * TotalBytes = 2123492744
[plustek] * PL=295, coeffsize=216, scaler=3
[plustek] * PauseLimit = 295, [0x4e] = 0x91, [0x4f] = 0x01
[plustek] * Scansteps=0 (3217226993*1200/150)
[plustek] usb_SetScanParameters() done.
[plustek] usbDev_getCaps()
[plustek] Scanner information:
[plustek] Vendor : Canon
[plustek] Model : LiDE25
[plustek] Flags : 0x00000000
[plustek] drvclose()
[plustek] usbDev_stopScan()
[plustek] usbDev_ScanEnd(), start=0, park=0
[plustek] usbDev_close()
[plustek] attach: model = >LiDE25<
[plustek] sane_get_devices (0xbfc322f8, 0)
Reply to: