Re: Can I install debian on a e300 board?
hi,
Thanks for your help and I have successfully run my custom kernel on my
board via loading a fdt file:
U-Boot 1.3.0 (Dec 22 2008 - 11:19:29) MPC83XX
Reset Status:
CPU: e300c3, MPC8313E, Rev: 21 at 333.333 MHz, CSB: 166 MHz
Board: Freescale MPC8313ERDB
I2C: ready
DRAM: 128 MB
FLASH: 8 MB
NAND: 32 MiB
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1 [PRIME]
Hit any key to stop autoboot: 0
=>
=> setenv serverip 192.168.0.104
=> setenv loadaddr 0x01000000
=> setenv fdtaddr 0x02000000
=> dhcp
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.0.103
Using TSEC1 device
TFTP from server 192.168.0.104; our IP address is 192.168.0.103
Filename 'uImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
########
done
Bytes transferred = 2021460 (1ed854 hex)
=> tftp 0x02000000 mpc8313erdb.dtb
Speed: 100, full duplex
Using TSEC1 device
TFTP from server 192.168.0.104; our IP address is 192.168.0.103
Filename 'mpc8313erdb.dtb'.
Load address: 0x2000000
Loading: #
done
Bytes transferred = 7721 (1e29 hex)
=> bootm 0x01000000 - 0x02000000
## Booting image at 01000000 ...
Image Name: Linux-2.6.39.1
Created: 2011-06-03 16:24:13 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2021396 Bytes = 1.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Booting using the fdt at 0x2000000
Loading Device Tree to 007fd000, end 007fee28 ... OK
Using MPC831x RDB machine description
Linux version 2.6.39.1 (bear@debian) (gcc version 4.4.5 (Debian 4.4.5-8)
) #1 Fri Jun 3 23:40:59 CST 2011
bootconsole [udbg0] enabled
setup_arch: bootmem
mpc831x_rdb_setup_arch()
Found FSL PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
PCI host bridge /sleep-nexus/pci@e0008500 (primary) ranges:
MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000
MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 Prefetch
IO 0x00000000e2000000..0x00000000e20fffff -> 0x0000000000000000
arch: exit
Zone PFN ranges:
DMA 0x00000000 -> 0x00008000
Normal empty
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: root=/dev/ram console=ttyS0,115200
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 124524k/131072k available (4080k kernel code, 6548k reserved,
148k data, 1107k bss, 184k init)
Kernel virtual memory layout:
* 0xfffdf000..0xfffff000 : fixmap
* 0xfdefb000..0xfe000000 : early ioremap
* 0xc9000000..0xfdefb000 : vmalloc & ioremap
SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:512 nr_irqs:512 16
IPIC (128 IRQ sources) at c9000700
clocksource: timebase mult[6000002] shift[22] registered
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource timebase
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
msgmni has been set to 245
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 16) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 17) is a 16550A
brd: module loaded
loop: module loaded
fe000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x000001 Chip ID 0x001001
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
fe000000.flash: Swapping erase regions for top-boot CFI table.
number of CFI chips: 1
cmdlinepart partition parsing not available
RedBoot partition parsing not available
fsl-lbc e0005000.localbus: read_byte beyond end of buffer
fsl-lbc e0005000.localbus: read_byte beyond end of buffer
fsl-lbc e0005000.localbus: read_byte beyond end of buffer
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB
3,3V 8-bit)
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 3 MTD partitions on "e2800000.flash":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000002000000 : "fs"
eLBC NAND device at 0xe2800000, bank 1
Fixed MDIO Bus: probed
fsl-gianfar e0024000.ethernet: enabled errata workarounds, flags: 0x7
eth0: Gianfar Ethernet Controller Version 1.2, 04:00:00:00:00:0a
eth0: Running with NAPI enabled
eth0: RX BD ring size for Q[0]: 256
eth0: TX BD ring size for Q[0]: 256
fsl-gianfar e0025000.ethernet: enabled errata workarounds, flags: 0x7
eth1: Gianfar Ethernet Controller Version 1.2, 04:00:00:00:00:0b
eth1: Running with NAPI enabled
eth1: RX BD ring size for Q[0]: 256
eth1: TX BD ring size for Q[0]: 256
Freescale PowerQUICC MII Bus: probed
Freescale PowerQUICC MII Bus: probed
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
/soc8313@e0000000/usb@23000: Invalid 'dr_mode' property, fallback to
host mode
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 38, io mem 0xe0023000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
mpc-i2c e0003000.i2c: timeout 1000000 us
rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
mpc-i2c e0003100.i2c: timeout 1000000 us
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
rtc-ds1307 0-0068: setting system clock to 2000-01-03 15:08:10 UTC
(946912090)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
List of all partitions:
1f00 8192 mtdblock0 (driver?)
1f01 1024 mtdblock1 (driver?)
1f02 3072 mtdblock2 (driver?)
1f03 28672 mtdblock3 (driver?)
No filesystem could mount root, tried: ext3 ext2
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(1,0)
Rebooting in 180 seconds..
But unfortunately, it seems like the kernel still need a rootfs? I have
a SD card and I wanna install debian into it. Is there anyone who can
tell me how to do? Thanks.
BTW: The official installer in Business Card CD seems not work with me:
U-Boot 1.3.0 (Dec 22 2008 - 11:19:29) MPC83XX
Reset Status:
CPU: e300c3, MPC8313E, Rev: 21 at 333.333 MHz, CSB: 166 MHz
Board: Freescale MPC8313ERDB
I2C: ready
DRAM: 128 MB
FLASH: 8 MB
NAND: 32 MiB
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1 [PRIME]
Hit any key to stop autoboot: 0
=> setenv serverip 192.168.0.104
=> setenv fdtaddr 0x02000000
=> setenv loadaddr 0x01000000
=> dhcp
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.0.103
Using TSEC1 device
TFTP from server 192.168.0.104; our IP address is 192.168.0.103
Filename 'uImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################
done
Bytes transferred = 6967619 (6a5143 hex)
=> tftp 0x02000000 mpc8313erdb.my.dtb
Speed: 100, full duplex
Using TSEC1 device
TFTP from server 192.168.0.104; our IP address is 192.168.0.103
Filename 'mpc8313erdb.my.dtb'.
Load address: 0x2000000
Loading: #
done
Bytes transferred = 7721 (1e29 hex)
=> bootm 0x01000000 - 0x02000000
## Booting image at 01000000 ...
Image Name: Debian-businesscard-squeeze
Created: 2011-06-03 11:37:07 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6967555 Bytes = 6.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
OK
Booting using the fdt at 0x2000000
Loading Device Tree to 007fd000, end 007fee28 ... OK
and it hang.
On 100/6/4 上午 05:13, Gerhard Pircher wrote:
-------- Original-Nachricht --------
Datum: Sat, 04 Jun 2011 01:27:03 +0800
Von: Bear<jilingshu@gmail.com>
An: Gerhard Pircher<gerhard_pircher@gmx.net>
CC: debian-powerpc@lists.debian.org
Betreff: Re: Can I install debian on a e300 board?
hi,
It's amazing! I tried Freescale default Linux image and it also halt!
U-Boot 1.3.0 (Dec 22 2008 - 11:19:29) MPC83XX
Reset Status:
CPU: e300c3, MPC8313E, Rev: 21 at 333.333 MHz, CSB: 166 MHz
Board: Freescale MPC8313ERDB
I2C: ready
DRAM: 128 MB
FLASH: 8 MB
NAND: 32 MiB
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1 [PRIME]
Hit any key to stop autoboot: 0
=>
=> setenv serverip 192.168.0.104
=> setenv loadaddr 0x01000000
=> dhcp
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.0.103
Using TSEC1 device
TFTP from server 192.168.0.104; our IP address is 192.168.0.103
Filename 'uImage'.
Load address: 0x1000000
Loading: #################################################################
##############################################
done
Bytes transferred = 1617371 (18addb hex)
=> bootm 0x01000000
## Booting image at 01000000 ...
Image Name: Linux-2.6.23
Created: 2008-12-22 3:22:49 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1617307 Bytes = 1.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
The default kernel should be boot correctly, but it also make my board
hang. Is there anybody can give me some advice? Thanks!
I would check, if U-Boot really hands over a device tree to the kernel
(the "fdt" command may be of use here). Otherwise you may have to load
a device tree file manually and specify its address as an argument for
the bootm command (if that is supported by your U-Boot version).
Gerhard
Reply to: