Re: no go for me with serial console, bug 364637 - WAS: Xserver G5 usb keyboard not loaded ...
On Thu, Apr 27, 2006 at 10:14:48AM -0400, Toni L. Harbaugh-Blackford [Contr] wrote:
> On Thu, 27 Apr 2006, Sven Luther wrote:
>
> > >
> > > Is this in the debian docs, or is there a reference somewhere to how
> > > to do it? If not, can you just give me a quick overview so I can
> > > figure out how to do it?
> >
> > the debian-installer documentation used to have some (incomplete) guidelines
> > to do this, not sure where they are now. The s390 installer guide sahould help
> > you since they have neither display nor serial console.
> >
> > > I know SuSE provides this via linuxrc, but I was not aware that debian
> > > did something similar.
> >
> > Well, it is a d-i feature, you use preseeding together with the ssh remote
> > console.
> >
>
> I don't see any mention of this in the s390 manual. The only description
> that seems relevant indicates that the installation system has to successfully
> boot before the network interface can be configured, which does not
> happen in this case.
Ask the d-i folk, they should know. look at the preseed stuff in the
documentation or something too, that is what i did.
>
> What is supposed to happen after 'Trying to im_free...' ?
Attaching the full log. The isa stuff is probably related to the graphic card.
Friendly,
Sven Luther
Page orders: linear mapping = 24, others = 12
Found initrd at 0xc000000001a00000:0xc000000001f2c400
Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x35
Mapped at 0xd000080080000000
Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000
PowerMac motherboard: XServe G5
DART: table not allocated, using direct DMA
Starting Linux PPC64 #2 SMP Tue Apr 25 15:35:40 CEST 2006
-----------------------------------------------------
ppc64_pft_size = 0x0
ppc64_interrupt_controller = 0x1
platform = 0x400
physicalMemorySize = 0x40000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0xc00000003e000000
htab_hash_mask = 0x1ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.16-1-vserver-powerpc64 (Debian 2.6.16-10) (waldi@debian.org) (gcc version 4.0.3 (Debian 4.0.3-1)) #2 SMP Tue Apr 25 15:35:40 CEST 2006
[boot]0012 Setup Arch
Top of RAM: 0x40000000, Total RAM: 0x40000000
Memory hole size: 0MB
Found U3-AGP PCI host bridge. Firmware bus number: 240->255
Can't get bus-range for /ht@0,f2000000, assume bus 0
Found U3-HT PCI host bridge. Firmware bus number: 0->239
PCI Host 0, io start: 400000; io end: bfffff
PCI Host 1, io start: 0; io end: 3fffff
via-pmu: Server Mode is disabled
PMU driver v2 initialized for Core99, firmware: 0c
nvram: Checking bank 0...
nvram: gen0=412, gen1=411
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 262144
DMA zone: 262144 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/sda4 ro
mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 120, shift: 7, mask: 7f
mpic: Initializing for 120 sources
mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 33.333333 MHz
time_init: processor frequency = 2300.000000 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
freeing bootmem node 0
Memory: 1004136k/1048576k available (3472k kernel code, 44440k reserved, 932k data, 305k bss, 244k init)
Calibrating delay loop... 66.56 BogoMIPS (lpj=33280)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
PowerMac SMP probe found 2 cpus
KeyWest i2c @0xf8001003 irq 128 /u3@0,f8000000/i2c@f8001000
channel 0 bus <multibus>
channel 1 bus <multibus>
KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@3/mac-io@7/i2c@18000
channel 0 bus <multibus>
PMU i2c /ht@0,f2000000/pci@3/mac-io@7/via-pmu@16000/pmu-i2c
channel 1 bus <multibus>
channel 2 bus <multibus>
Processor timebase sync using Pulsar i2c clock
requesting IPIs ...
IPIs requested...
Processor 1 found.
Brought up 2 CPUs
migration_cost=712
checking if image is initramfs... it is
Freeing initrd memory: 5297k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
mapping IO f0000000 -> d000080000400000, size: 800000
mapping IO f4000000 -> d000080000000000, size: 400000
PCI: Probing PCI hardware done
Registering pmac pic with sysfs...
nvram_init: Could not find nvram partition for nvram buffered error logging.
audit: initializing netlink socket (disabled)
audit(1146164324.691:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
radeonfb: Found Open Firmware ROM Image
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=150.00 Mhz, System=150.00 MHz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Trying to im_free nonexistent area (d0000800800c1000)
Console: switching to colour frame buffer device 128x48
radeonfb (0001:06:03.0): ATI Radeon QY
vio_register_driver: driver hvc_console registering
HVSI: registered 0 devices
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
pmac_zilog: Error registering serial device, disabling pmac_zilog.
pmac_zilog: Did another serial driver already claim the minors?
Trying to im_free nonexistent area (d00008008216c000)
Trying to im_free nonexistent area (d00008008216e000)
isa bounce pool size: 16 pages
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
vroot: loaded (max 8 devices)
MacIO PCI driver attached to K2 chipset
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI: Enabling device: (0001:03:0d.0), cmd 16
ide0: Found Apple K2 ATA-6 controller, bus ID 3, irq 39
Probing IDE interface ide0...
hda: MATSHITADVD-R UJ-845, ATAPI CD/DVD-ROM drive
hda: Enabling Ultra DMA 2
ide0 at 0xd000080083258000-0xd000080083258007,0xd000080083258160 on irq 39
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 244k freed
PowerMac G5 Thermal control driver 1.2b2
Detected fan controls:
0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN
1: RPM fan, id 2, location: DRIVE BAY
2: PWM fan, id 2, location: SLOT,PCI FAN
3: RPM fan, id 3, location: CPU A INTAKE
4: RPM fan, id 4, location: CPU A EXHAUST
5: RPM fan, id 5, location: CPU B INTAKE
6: RPM fan, id 6, location: CPU B EXHAUST
9: RPM fan, id 1, location: CPU A 1
10: RPM fan, id 2, location: CPU A 2
11: RPM fan, id 3, location: CPU A 3
12: RPM fan, id 4, location: CPU B 1
13: RPM fan, id 5, location: CPU B 2
14: RPM fan, id 6, location: CPU B 3
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
tg3.c:v3.49 (Feb 2, 2006)
eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:93:9d:dd:ce
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[769f4000] dma_mask[32-bit]
eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:93:9d:dd:cf
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[32-bit]
SCSI subsystem initialized
libata version 1.20 loaded.
sata_svw 0001:05:0c.0: version 1.07
ata1: SATA max UDMA/133 cmd 0xD00008008327A000 ctl 0xD00008008327A020 bmdma 0xD00008008327A030 irq 0
ata2: SATA max UDMA/133 cmd 0xD00008008327A100 ctl 0xD00008008327A120 bmdma 0xD00008008327A130 irq 0
ata3: SATA max UDMA/133 cmd 0xD00008008327A200 ctl 0xD00008008327A220 bmdma 0xD00008008327A230 irq 0
ata4: SATA max UDMA/133 cmd 0xD00008008327A300 ctl 0xD00008008327A320 bmdma 0xD00008008327A330 irq 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:007f
ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_svw
ata2: SATA link down (SStatus 4)
scsi1 : sata_svw
ata3: SATA link down (SStatus 4)
scsi2 : sata_svw
ata4: SATA link down (SStatus 4)
scsi3 : sata_svw
Vendor: ATA Model: Maxtor 6B080M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
PCI: Enabling device: (0001:03:0e.0), cmd 2
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[80200000-802007ff] Max Packet=[4096] IR/IT contexts=[8/8]
PCI: Enabling device: (0001:02:0b.0), cmd 2
ohci_hcd 0001:02:0b.0: OHCI Host Controller
ohci_hcd 0001:02:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:02:0b.0: irq 63, io mem 0x80102000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
PCI: Enabling device: (0001:02:0b.1), cmd 2
ohci_hcd 0001:02:0b.1: OHCI Host Controller
ohci_hcd 0001:02:0b.1: new USB bus registered, assigned bus number 2
ohci_hcd 0001:02:0b.1: irq 63, io mem 0x80101000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device: (0001:02:0b.2), cmd 6
ehci_hcd 0001:02:0b.2: EHCI Host Controller
ehci_hcd 0001:02:0b.2: new USB bus registered, assigned bus number 3
ehci_hcd 0001:02:0b.2: irq 63, io mem 0x80100000
ehci_hcd 0001:02:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 5 ports detected
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: Attached scsi disk sda
ieee1394: Host added: ID:BUS[0-01:1023] GUID[001124fffe4531cc]
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 2-2: new low speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Apple U3H chipset
agpgart: configuring for size idx: 64
agpgart: AGP aperture is 256M @ 0x0
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
usbcore: registered new driver hiddev
input: Logitech USB Receiver as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0001:02:0b.1-2
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0001:02:0b.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
EXT3 FS on sda4, internal journal
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Reply to: