Re: ben_kernel_install_hangs
jean-michel wrote:
> vector: 200 at pc =00000300, lr = c02fca28
> msr = 41000, sp = c03f7f30 [c03f7e80]
> current = c03f60000, pid = 1, comm = swapper
> mon>
>
> and the cursor just kept on flashing, expecting me, no doubt, to type
> something intelligent. After some googling, and discovered i might
> have to change the video driver setting in BootX and rebooting, the
> process went quite
> a bit further ( detecting hubs, busses mice, etc) . It got to the line
> :
>
> /dev/sdb8: clean, 99818/1300480 files, 65324/2596864 blocks
>
> then the following message shows up in the middle of the screen in
> bold:
>
> vector: 600 at pc =c007dc80, lr = c007dc78
> msr =9032, sp = d1d13e70 [d1d13dc0]
> dar = 7, dsisr = 5d07
> current = d1d12000, pid = 32, comm = mount
> mon> (flashing cursor)
Ben replied:
Both of these would be easier to parse if you could lookup the PC and
LR values in System.map
Also, what additional HW do you have in the machine ?
Reply :
Pardon my ignorance, but i don't know what i'm looking for : LR and PC
values? "Grepping" System.map for LR,PC,lr,pc,or any of the 4 numerical
values,pc =00000300, lr = c02fca28,pc =c007dc80, lr = c007dc78 shows
nothing.
Tell me what i'm looking for. i'll look again.
My hardware is pretty standard :
Mac 7300/180
original apple 2G HDD SCSI
Fujitsu 18G HDD SCSI (added, a while ago)
288meg RAM
USB pci card (added, not recently)
Applevision 1710 Monitor (not AV)
For a more precise list of my hardware,
a long exerpt from dmesg from booting with
2.2.20-pmac follows below.
Total memory = 288MB; using 2048kB for hash table (at c0400000)
PCI bus 0 controlled by bandit at f2000000
Cache coherency enabled for bandit/PSX at f2000000
PCI bus 1 controlled by chaos at f0000000
pmac nvram is core99: 0
System has 32 possible interrupts
GMT Delta read from XPRAM: -240 minutes, DST: on
via_calibrate_decr: decrementer_count = 112502 (675012 ticks)
Console: colour dummy device 80x25
Calibrating delay loop... 359.62 BogoMIPS
Memory: 286912k available (1716k kernel code, 6100k data, 184k init)
[c0000000,d2000000]
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k)
Page cache hash table entries: 131072 (order 7, 512k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
adb devices: [2]: 2 5 [3]: 3 1 [14]: 14 c0
MacOS display is /chaos/control
Monitor sense value = 0x62b, using video mode 17 and color mode 1.
fb0: control display adapter
input0: Macintosh mouse button emulation
ADB keyboard at 2, handler set to 3
input1: ADB HID on ID 2:2.05
ADB mouse at 3, handler set to 2
input2: ADB HID on ID 3:3.01
PowerMac Z8530 serial driver version 2.0
tty00 at 0xf3013020 (irq = 15) is a Z8530 ESCC, port = modem
tty01 at 0xf3013000 (irq = 16) is a Z8530 ESCC, port = printer
pty: 256 Unix98 ptys configured
fd0: SWIM3 floppy controller
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
scsi0 : MESH
scsi1 : 53C94
scsi : 2 hosts.
mesh: target 0 synchronous at 10.0 MB/s
Vendor: QUANTUM Model: FIREBALL ST2100S Rev: 0F0D
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
mesh: target 1 synchronous at 10.0 MB/s
Vendor: FUJITSU Model: MAA3182SC Rev: 0109
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
mesh: target 3 synchronous at 10.0 MB/s
Vendor: MATSHITA Model: CD-ROM CR-8012 Rev: 1.0g
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
scsi : detected 3 SCSI generics 1 SCSI cdrom 2 SCSI disks total.
Uniform CD-ROM driver Revision: 3.11
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4201304 [2051 MB] [2.1
GB] SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35680750 [17422
MB] [17.4 GB]
eth0: MACE at 00:05:02:d6:c0:74, chip revision 25.64
3c59x.c 18Feb01 Donald Becker and others
http://www.scyld.com/network/vortex.html
Partition check:
sda: sda1 sda2 sda3 sda4 sda5 sda6
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
event0: Event device for input2
event1: Event device for input1
event2: Event device for input0
usb.c: registered new driver hid
keybdev.c: Adding keyboard: input1
mouse0: PS/2 mouse device for input2
mouse1: PS/2 mouse device for input0
mice: PS/2 mouse device common for all mice
usb-ohci.c: USB OHCI at membase 0xd4803000, IRQ 24
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: USB new device connect, assigned device number 2
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: USB new device connect on bus1/2/1, assigned device number 3
usb.c: USB new device connect, assigned device number 3
input3: USB HID v10.01 Keyboard [Alps Electric Apple Extended USB
Keyboard] on usb1:3.0
input4: USB HID v10.01 Device [Alps Electric Apple Extended USB
Keyboard] on usb1:
--
jean-michel
Reply to: