Re: ACPI support on Compaq Presario 2500
On Friday 06 October 2006 03:24, Jörg-Volker Peetz wrote:
> Yoanis Gil Delgado wrote:
> > root@hogwarts:/sys/devices/system/cpu/cpu0# modprobe acpi-cpufreq
> > FATAL: Error inserting acpi_cpufreq
> > (/lib/modules/2.6.16-2-686/kernel/arch/i386/kernel/cpu/cpufreq/acpi-cpufr
> >eq.ko): No such device
> >
> > :(
> >
> > Regards,
> > Yoanis.
>
> Sorry, now I am helpless. Just for completeness I would like to see the
> content of "/var/log/dmesg" which shows what hardware has been found
> during booting, and the output of "dmidecode" which shows information
> about harware and BIOS.
>
> Regards,
> Jörg-Volker.
These is the output from the commands you requested.
Regards,
Yoanis
I15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2040-0x2047, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2048-0x204f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
hda: FUJITSU MHT2060AT PL, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DW-224E-A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
PCI: Enabling device 0000:00:0b.2 (0010 -> 0012)
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.2: irq 11, io mem 0xd0005000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda:ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNK2] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:0b.0: UHCI Host Controller
uhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:0b.0: irq 10, io base 0x00002000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 1658kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:0b.1: UHCI Host Controller
uhci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:0b.1: irq 10, io base 0x00002020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 3-2: new low speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0a.0 [0000:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01111112, devctl 0x64
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
usbcore: registered new driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Real Time Clock Driver v1.12ac
Yenta: ISA IRQ mask 0x0078, PCI irq 11
Socket status: 30000006
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Ati IGP345M chipset
agpgart: AGP aperture is 64M @ 0xd4000000
ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted.
ts: Compaq touchscreen protocol output
mice: PS/2 mouse device common for all mice
PCI: Enabling device 0000:00:06.0 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNK7] -> GSI 5 (level, low) -> IRQ 5
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input3
AC'97 1 does not respond - RESET
AC'97 1 access is not valid [0xffffffff], removing mixer.
ali mixer 1 creating error.
Adding 498004k swap on /dev/hda3. Priority:-1 extents:1 across:498004k
EXT3 FS on hda5, internal journal
loop: loaded (max 8 devices)
ndiswrapper version 1.23 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5 (Broadcom,10/28/2003, 3.40.25.3) loaded
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10
ndiswrapper: using irq 10
wlan0: vendor: ''
wlan0: ethernet device 00:90:4b:4b:5b:81 using NDIS driver bcmwl5, 14E4:4320:0E11:00E7.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
ndiswrapper: changing interface name from 'wlan0' to 'eth1'
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.26 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs error (device hda1): load_system_files(): $LogFile is not clean. Mounting read-only. Mount in Windows.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
eth1: no IPv6 routers present
serial8250: too much work for irq10
serial8250: too much work for irq10
serial8250: too much work for irq10
serial8250: too much work for irq10
serial8250: too much work for irq10
nacctd uses obsolete (PF_INET,SOCK_PACKET)
/dev/vmmon[4156]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[4156]: Module vmmon: initialized
/dev/vmnet: open called by PID 4176 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: peer interface eth0 not found, will wait for it to come up
bridge-eth0: attached
/dev/vmnet: open called by PID 4191 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 4192 (vmnet-netifup)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 4190 (vmnet-natd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 4228 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 4237 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized radeon 1.22.0 20051229 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
bridge-eth0: enabling the bridge
bridge-eth0: up
atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
ACPI: read EC, OB not full
ACPI Exception (evregion-0409): AE_TIME, Returned by Handler for [EmbeddedControl] [20060127]
ACPI Exception (dswexec-0458): AE_TIME, While resolving operands for [AE_NOT_CONFIGURED] [20060127]
ACPI Error (psparse-0517): Method parse/execution failed [\_SB_.PCI0.ISA_.EC0_._Q20] (Node b13fab00), AE_TIME
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: SanDisk Model: Cruzer Mini Rev: 0.1
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
slamr: SmartLink AMRMO modem.
slamr: device 10b9:5457 is grabbed by another driver
slamr: SmartLink AMRMO modem.
slamr: device 10b9:5457 is grabbed by another driver
apm: BIOS not found.
apm: BIOS not found.
apm: BIOS not found.
ACPI: read EC, OB not full
ACPI Exception (evregion-0409): AE_TIME, Returned by Handler for [EmbeddedControl] [20060127]
ACPI Exception (dswexec-0458): AE_TIME, While resolving operands for [AE_NOT_CONFIGURED] [20060127]
ACPI Error (psparse-0517): Method parse/execution failed [\_SB_.PCI0.ISA_.EC0_.SMSL] (Node b13fac20), AE_TIME
ACPI Error (psparse-0517): Method parse/execution failed [\_SB_.PCI0.ISA_.EC0_._Q09] (Node b13fab80), AE_TIME
eth0: remaining active for wake-on-lan
bridge-eth0: disabling the bridge
bridge-eth0: down
ndiswrapper: device eth1 removed
ACPI: PCI interrupt for device 0000:00:09.0 disabled
Stopping tasks: =============================================================================================================================================================|
Shrinking memory... -\|/-done (61181 pages freed)
pnp: Device 00:08 disabled.
ACPI: PCI interrupt for device 0000:00:0b.2 disabled
ACPI: PCI interrupt for device 0000:00:0b.1 disabled
ACPI: PCI interrupt for device 0000:00:0b.0 disabled
ACPI: PCI interrupt for device 0000:00:0a.0 disabled
ACPI: PCI interrupt for device 0000:00:06.0 disabled
swsusp: Need to copy 47173 pages
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal LVT vector (0xf0) already installed
swsusp: Restoring Highmem
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNK7] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNK6] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNK2] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10
pnp: Device 00:05 does not supported activation.
pnp: Device 00:06 does not supported activation.
pnp: Device 00:08 activated.
Restarting tasks...<6>usb 1-2: USB disconnect, address 3
done
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Medium error -- (Sense key=0x03)
(reserved error code) -- (asc=0x57, ascq=0x00)
The failed "Read Cd/Dvd Capacity" packet command was:
"25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 "
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
natsemi eth0: NatSemi DP8381[56] at 0xd0006000 (0000:00:12.0), 00:0e:7f:eb:8a:5a, IRQ 10, port TP.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input4
ndiswrapper version 1.23 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5 (Broadcom,10/28/2003, 3.40.25.3) loaded
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10
ndiswrapper: using irq 10
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Medium error -- (Sense key=0x03)
(reserved error code) -- (asc=0x57, ascq=0x00)
The failed "Read Cd/Dvd Capacity" packet command was:
"25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Medium error -- (Sense key=0x03)
(reserved error code) -- (asc=0x57, ascq=0x00)
The failed "Read Cd/Dvd Capacity" packet command was:
"25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 "
cdrom: This disc doesn't have any tracks I recognize!
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Medium error -- (Sense key=0x03)
(reserved error code) -- (asc=0x57, ascq=0x00)
The failed "Read Cd/Dvd Capacity" packet command was:
"25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 "
wlan0: vendor: ''
wlan0: ethernet device 00:90:4b:4b:5b:81 using NDIS driver bcmwl5, 14E4:4320:0E11:00E7.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
ndiswrapper: changing interface name from 'wlan0' to 'eth1'
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Medium error -- (Sense key=0x03)
(reserved error code) -- (asc=0x57, ascq=0x00)
The failed "Read Cd/Dvd Capacity" packet command was:
"25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 "
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
bridge-eth0: enabling the bridge
bridge-eth0: up
eth0: no IPv6 routers present
# dmidecode 2.8
SMBIOS 2.3 present.
31 structures occupying 1166 bytes.
Table at 0x000DB010.
Handle 0x0000, DMI type 0, 20 bytes
BIOS Information
Vendor: Phoenix Technologies Ltd.
Version: KF_KH.F.24
Release Date: 10/26/2004
Address: 0xE4AA0
Runtime Size: 111968 bytes
ROM Size: 512 kB
Characteristics:
ISA is supported
PCI is supported
PC Card (PCMCIA) is supported
PNP is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
Boot from PC Card (PCMCIA) is supported
EDD is supported
Japanese floppy for NEC 9800 1.2 MB is supported (int 13h)
Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
AGP is supported
Handle 0x0001, DMI type 1, 25 bytes
System Information
Manufacturer: Hewlett-Packard
Product Name: Presario 2500 (DS543U)
Version: KH.F.24
Serial Number: CNF35303C2
UUID: 40BFA86D-592F-D811-9468-000E7FEB8A5A
Wake-up Type: Power Switch
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Hewlett-Packard
Product Name: 0850
Version: NS570 Version PQ1B60
Serial Number: None
Handle 0x0003, DMI type 3, 17 bytes
Chassis Information
Manufacturer: Hewlett-Packard
Type: Notebook
Lock: Not Present
Version: N/A
Serial Number: None
Asset Tag: No Asset Tag
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00000000
Handle 0x0004, DMI type 4, 32 bytes
Processor Information
Socket Designation: WMT478/NWD
Type: Central Processor
Family: Pentium 4
Manufacturer: Intel
ID: 29 0F 00 00 FF F9 EB BF
Signature: Type 0, Family 15, Model 2, Stepping 9
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Pentium(R) 4
Voltage: 1.2 V
External Clock: Unknown
Max Speed: 2667 MHz
Current Speed: 2667 MHz
Status: Populated, Enabled
Upgrade: Slot 1
L1 Cache Handle: Not Provided
L2 Cache Handle: 0x0008
L3 Cache Handle: Not Provided
Handle 0x0005, DMI type 5, 20 bytes
Memory Controller Information
Error Detecting Method: None
Error Correcting Capabilities:
Other
Supported Interleave: One-way Interleave
Current Interleave: One-way Interleave
Maximum Memory Module Size: 512 MB
Maximum Total Memory Size: 1024 MB
Supported Speeds:
70 ns
60 ns
Supported Memory Types:
FPM
EDO
DIMM
SDRAM
Memory Module Voltage: 3.3 V
Associated Memory Slots: 2
0x0000
0x0001
Enabled Error Correcting Capabilities:
None
Handle 0x0006, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: DIMM 1
Bank Connections: 0 1
Current Speed: 60 ns
Type: DIMM SDRAM
Installed Size: 256 MB (Single-bank Connection)
Enabled Size: 256 MB (Single-bank Connection)
Error Status: OK
Handle 0x0007, DMI type 6, 12 bytes
Memory Module Information
Socket Designation: DIMM 2
Bank Connections: 2 3
Current Speed: 60 ns
Type: DIMM SDRAM
Installed Size: Not Installed
Enabled Size: Not Installed
Error Status: OK
Handle 0x0008, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 512 KB
Maximum Size: 1024 KB
Supported SRAM Types:
Burst
Pipeline Burst
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: 2-way Set-associative
Handle 0x0009, DMI type 9, 13 bytes
System Slot Information
Designation: PCI Slot 1
Type: 32-bit PCI
Current Usage: Unknown
Length: Long
ID: 0
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x000A, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Disabled
Description: ALi 1535 Sound
Handle 0x000B, DMI type 11, 5 bytes
OEM Strings
String 1: Compaq Notebook Series
String 2: Service ID: 14090
String 3: $MODEL: DS543
String 4: $OS:
String 5: $LOCAL: ABA
String 6: $OPTION:
String 7: $DC:
Handle 0x000C, DMI type 12, 5 bytes
System Configuration Options
Option 1: Jumper settings can be described here.
Handle 0x000D, DMI type 15, 29 bytes
System Event Log
Area Length: 16 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: General-purpose non-volatile data functions
Access Address: 0x0000
Status: Valid, Not Full
Change Token: 0x00000004
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: Single-bit ECC memory error
Data Format 2: Multiple-event
Descriptor 3: Multi-bit ECC memory error
Data Format 3: Multiple-event
Handle 0x000E, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 1 GB
Error Information Handle: Not Provided
Number Of Devices: 3
Handle 0x000F, DMI type 17, 23 bytes
Memory Device
Array Handle: 0x000E
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 256 MB
Form Factor: DIMM
Set: 1
Locator: J400
Bank Locator: DIMM 1
Type: DRAM
Type Detail: Synchronous
Speed: Unknown
Handle 0x0010, DMI type 17, 23 bytes
Memory Device
Array Handle: 0x000E
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 256 MB
Form Factor: DIMM
Set: 1
Locator: J401
Bank Locator: DIMM 2
Type: DRAM
Type Detail: Synchronous
Speed: Unknown
Handle 0x0011, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0001FFFFFFF
Range Size: 512 MB
Physical Array Handle: 0x000E
Partition Width: 0
Handle 0x0012, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0000FFFFFFF
Range Size: 256 MB
Physical Device Handle: 0x000F
Memory Array Mapped Address Handle: 0x0011
Partition Row Position: 1
Handle 0x0013, DMI type 23, 13 bytes
System Reset
Status: Enabled
Watchdog Timer: Present
Boot Option: Do Not Reboot
Boot Option On Limit: Do Not Reboot
Reset Count: Unknown
Reset Limit: Unknown
Timer Interval: Unknown
Timeout: Unknown
Handle 0x0014, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Disabled
Keyboard Password Status: Unknown
Administrator Password Status: Enabled
Front Panel Reset Status: Unknown
Handle 0x0015, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: 12-31 23:59:59
Handle 0x0016, DMI type 26, 20 bytes
Voltage Probe
Description: Voltage Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0017, DMI type 27, 14 bytes
Cooling Device
Temperature Probe Handle: 0x0018
Type: Fan
Status: OK
OEM-specific Information: 0x00000000
Nominal Speed: Unknown Or Non-rotating
Handle 0x0018, DMI type 28, 20 bytes
Temperature Probe
Description: Temperature Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0019, DMI type 29, 20 bytes
Electrical Current Probe
Description: Electrical Current Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x001A, DMI type 30, 6 bytes
Out-of-band Remote Access
Manufacturer Name: Intel
Inbound Connection: Enabled
Outbound Connection: Disabled
Handle 0x001B, DMI type 32, 20 bytes
System Boot Information
Status: <OUT OF SPEC>
Handle 0x001C, DMI type 133, 34 bytes
OEM-specific Type
Header and Data:
85 22 1C 00 01 30 11 DB C1 EE C0 19 00 9B 00 1E
00 02 41 01 01 D0 39 02 80 00 46 10 33 10 4B 10
3E 10
Strings:
00007 12/25/2003
SMP
Handle 0x001D, DMI type 140, 36 bytes
OEM-specific Type
Header and Data:
8C 24 1D 00 00 00 00 00 00 60 01 7D 00 7C 01 7D
00 00 00 01 FF FF FF FF FF FF FF FF 00 00 00 00
00 00 00 00
Handle 0x001E, DMI type 127, 4 bytes
End Of Table
Reply to: