Re: Is it possible to use Carbus NIC on kernel 2.4.12 without pcmcia-modules?

[Kazuhiko Uebayashi <u_kazu@nifty.com>]

Hi, everyone.

I appreciate many reply.

After all I had better to install pcmcia-modules.

I'll try this way. 

	Thanks any way. 


On Sat, 27 Oct 2001 04:05:49 +0900
Kazuhiko Uebayashi <u_kazu@nifty.com> wrote:

> Hi, I'm Kazuhiko Uebayashi.
> 
> I'm in trouble now in using Cardbus NIC(Network Interface Card).
> 
> On kernel 2.2.19 with pcmcia-modules(make-kpkg from pcmcia-source),
> I can use this Cardbus NIC.
> 
> But after I change kernel to 2.4.12,it dosen't work well.
> 
> /var/log/syslog says the following, 
> ------------------------
> Oct 27 03:55:01 darkstar kernel: cs: cb_free(bus 21)
> Oct 27 03:55:01 darkstar cardmgr[201]: shutting down socket 1
> Oct 27 03:55:01 darkstar cardmgr[201]: executing: 'modprobe -r tulip_cb'
> Oct 27 03:55:01 darkstar cardmgr[201]: executing: 'modprobe -r cb_enabler'
> Oct 27 03:55:03 darkstar kernel: cs: cb_alloc(bus 21): vendor 0x13d1, device 0xab02
> Oct 27 03:55:03 darkstar kernel: PCI: Enabling device 15:00.0 (0000 -> 0003)
> Oct 27 03:55:03 darkstar cardmgr[201]: initializing socket 1
> Oct 27 03:55:03 darkstar cardmgr[201]: socket 1: Linksys Etherfast 10/100
> Oct 27 03:55:03 darkstar cardmgr[201]: executing: 'modprobe cb_enabler'
> Oct 27 03:55:03 darkstar cardmgr[201]: + modprobe: Can't locate module cb_enabler
> Oct 27 03:55:03 darkstar cardmgr[201]: modprobe exited with status 255
> Oct 27 03:55:03 darkstar cardmgr[201]: module /lib/modules/2.4.12/pcmcia/cb_enabler.o not available
> Oct 27 03:55:03 darkstar cardmgr[201]: executing: 'modprobe tulip_cb'
> Oct 27 03:55:03 darkstar cardmgr[201]: + modprobe: Can't locate module tulip_cb
> Oct 27 03:55:03 darkstar cardmgr[201]: modprobe exited with status 255
> Oct 27 03:55:03 darkstar cardmgr[201]: module /lib/modules/2.4.12/pcmcia/tulip_cb.o not available
> Oct 27 03:55:04 darkstar cardmgr[201]: get dev info on socket 1 failed: Resource temporarily unavailable
> --------------------------.
> 
> I can't understand well what the log means.
> 
> Is it possible to use Carbus NIC (ADMtek 985 Chip) 
> on kernel 2.4.12 without pcmcia-modules?
> 
> Could you tell me how to use this CardBus NIC without  pcmcia-modules?
> 
> In case  using pcmcia-modules, 
> Do I had better to remove pcmcia-net-driver support from kernel?
> 
> -- 
> Kazuhiok Uebyashi 
> e-mail : u_kazu@nifty.com
> 
> 
> -- 
> To UNSUBSCRIBE, email to debian-laptop-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
> 
> 


-- 
Kazuhiok Uebyashi 
e-mail : u_kazu@nifty.com