Re: pcmcia problem
> Sounds like your card is recognised as being some sort of PCNET variant,
> but you will need to build a "binary-modules" target from the 3.1.25
> source. The pcmcia-cs source will build either or both packages for you
> - take a look at the debian/rules file for what targets are valid. From
> memory I think you want "binary-modules" and "binary-cs".
>
> Hope this helps,
No, it didn't help. But it was a good exercise.
I had built the pcmcia-cs source 3.1.25 package before. It was the
non-debian version from sourceforge. I didn't know I could get a 3.1.25
debian package from unstable.
Now there was a slight chance that the debian package would do better
than the non-debian version, but it didn't.
Both binary-modules and binary-cs built fine, and I have the new modules
in /lib/modules...
I'm still getting the following dmeg output:
...
Linux PCMCIA Card Services 3.1.25
kernel build: 2.2.18pre21 #1 Sat Nov 18 18:47:15 EST 2000
options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf0180
00:02.0 -> irq 11
00:02.1 -> irq 11
ds: no socket drivers loaded!
unloading PCMCIA Card Services
Detected Parameters Irq=3 BaseAddress=0x1c00 ComAddress=0x2f8
Lucent Modem driver version 5.78e with no serial options enabled
ttyLT00 at 0x1c00 (irq = 3) is a Lucent
Linux PCMCIA Card Services 3.1.25
kernel build: 2.2.18pre21 #1 Sat Nov 18 18:47:15 EST 2000
options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf0180
Intel PCIC probe:
Toshiba ToPIC97 rev 05 PCI-to-CardBus at slot 00:02, mem 0x68000000
host opts [0]: [slot 0xf0] [ccr 0x11] [cdr 0x86] [rcr 0x00] [pci irq 11]
[lat 168/176] [bus 20/20]
host opts [1]: [slot 0xf0] [ccr 0x21] [cdr 0x86] [rcr 0x00] [pci irq 11]
[lat 168/176] [bus 21/21]
PCI irq 11 test failed
ISA irqs (default) = 4,5,7,9,10,12 polling interval = 1000 ms
Toshiba System Managment Mode driver v1.7 22/6/2000
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 8250
cs: memory probe 0x0d0000-0x0dffff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0380-0x04cf: clean.
cs: IO port probe 0x04d8-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
pcnet_cs: sorry, the AX88190 chipset is not supported.
pcnet_cs: unable to read hardware net address for io base 0x300
mtrr: base(0xff800000) is not aligned on a size(0x280000) boundary
pcnet_cs: sorry, the AX88190 chipset is not supported.
pcnet_cs: unable to read hardware net address for io base 0x300
And I'm still getting a high and a low beep when I insert the card.
What other files and settings are relevant here? What could I try?
Thank you.
Robert
Reply to: