DGA Problems....(and other graphic stuff)
I have been trying on and off over the past couple of weeks to get DGA to
work on my laptop with the latest X 4.0.2. My graphics card is a Trident
Cyber 9397, however if I enable the loading of the DGA module (as you can
see in my XF86Config) and then run /usr/X11R6/bin/dga as root I get the
following error
"Xserver driver doesn't support DirectVideo on screen 0"
any ideas? I'm am keeping my fingers crossed that this doesn't mean that
the trident drivers doesn't support DGA, although it says in the error
message that it doesn't :)
I have also included my XFree86.log file. I have spent a while turning on
and off the acceleration features of X, and have found ones which work
(through suspend/resume cycles) however I hope I haven't tweaked something
that his killed DGA. I don't think this is the case as I have also tried
turning off all the acceleration features and still I get the same error
message.
Whilst I'm talking about video stuff, can someone tell me how to set up my
mtrr registers properly. It seems my graphics card has several regions
instead of one continuous region (like in all the internet examples :( ).
I have supplied a copy of /proc/pci (aka pciscan) and /proc/mtrr (aka
mtrr) so that someone who has the "knowledge" can help me :)
anyone have any suggestions on how to setup SVGAlib for my laptop, so I
don't get the *very* scary melt/streak screen of destruction?
one last thing, in my XF86Config file there are one or two acceleration
options which are undocumented in the current release however they were in
the 3.3.x series. Any ideas on what to do with them for good performance?
thanks for any help you can give me
Alex
PS. this is not being done for movies (although it would be nice, I know
I flamed about linux/multimedia a few weeks back), its more so that I can
squeeze a littl' more battery time out of my laptop :)
reg00: base=0x00000000 ( 0MB), size= 64MB: write-back, count=1
reg01: base=0xfe400000 (4068MB), size= 4MB: write-combining, count=1
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 3).
Master Capable. Latency=64.
Prefetchable 32 bit memory at 0xf8000000 [0xfbffffff].
Bus 0, device 2, function 0:
VGA compatible controller: Trident Microsystems Cyber 9397 (rev 243).
Master Capable. Latency=64.
Non-prefetchable 32 bit memory at 0xfe400000 [0xfe7fffff].
Non-prefetchable 32 bit memory at 0xfede0000 [0xfedfffff].
Non-prefetchable 32 bit memory at 0xfe800000 [0xfebfffff].
Bus 0, device 3, function 0:
CardBus bridge: O2 Micro, Inc. 6836 (rev 98).
IRQ 11.
Master Capable. Latency=64. Max Lat=4.
Non-prefetchable 32 bit memory at 0x10000000 [0x10000fff].
Bus 0, device 3, function 1:
CardBus bridge: O2 Micro, Inc. 6836 (#2) (rev 98).
IRQ 11.
Master Capable. Latency=64. Min Gnt=128.Max Lat=4.
Non-prefetchable 32 bit memory at 0x10001000 [0x10001fff].
Bus 0, device 7, function 0:
ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 2).
Bus 0, device 7, function 1:
IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 1).
Master Capable. Latency=64.
I/O at 0xfcd0 [0xfcdf].
Bus 0, device 7, function 2:
USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 1).
IRQ 11.
Master Capable. Latency=64.
I/O at 0xfce0 [0xfcff].
Bus 0, device 7, function 3:
Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 2).
Bus 1, device 0, function 0:
Ethernet controller: (rev 65).
IRQ 11.
Master Capable. Latency=64. Min Gnt=20.Max Lat=40.
XFree86 Version 4.0.2 / X Window System
(protocol Version 11, revision 0, vendor release 6400)
Release Date: 18 December 2000
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.18 i686 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Sun Mar 25 23:08:31 2001
(==) Using config file: "/etc/X11/XF86Config"
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (??) unknown.
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "My Monitor"
(**) | |-->Device "Trident Cyber 9397 (generic)"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc104"
(**) XKB: model: "pc104"
(**) Option "XkbLayout" "gb"
(**) XKB: layout: "gb"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/TrueType/,/usr/lib/X11/fonts/misc/:unscaled,/usr/lib/X11/fonts/75dpi/:unscaled"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 5
(II) Open APM successful
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.3
XFree86 XInput driver : 0.1
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.2
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.2
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7192 card 0000,0000 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:02:0: chip 1023,9397 card 0002,e320 rev f3 class 03,00,00 hdr 00
(II) PCI: 00:03:0: chip 1217,6836 card 0401,0000 rev 62 class 06,07,00 hdr 82
(II) PCI: 00:03:1: chip 1217,6836 card 0001,0000 rev 62 class 06,07,00 hdr 82
(II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 02 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00
(II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 02 class 06,80,00 hdr 00
(II) PCI: 01:00:0: chip 1011,0019 card 1385,2100 rev 41 class 02,00,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus 0 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:7:0), (0,-1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(II) Bus 1: bridge is at (0:0:0), (-1,1,0), BCTRL: 0x00 (VGA_EN is cleared)
(II) Bus 1 I/O range:
[0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
(--) PCI:*(0:2:0) Trident Cyber 9397 rev 243, Mem @ 0xfe400000/22, 0xfede0000/17, 0xfe800000/22
(II) Addressable bus resource ranges are
[0] -1 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) Active PCI resource ranges:
[0] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[1] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[2] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[3] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[4] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[5] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[6] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[7] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[8] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[1] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[2] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[3] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[4] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[5] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[6] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[7] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[8] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
(II) All system resource ranges:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[6] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[7] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[10] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[11] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[12] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[13] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[14] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.2
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.1.8
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.2
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) LoadModule: "trident"
(II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o
(II) Module trident: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.3
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.1
(II) TRIDENT: driver for Trident chipsets: tvga8900d, cyber9320, cyber9388,
cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4,
tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682,
providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d,
cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d,
cyberbladeAi1, cyberbladeAi1d
(II) Primary Device is: PCI 00:02:0
(--) Assigning device section with no busID to primary device
(--) Chipset cyber9397 found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[6] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[7] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[10] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[11] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[12] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[13] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[14] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[6] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[7] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[8] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[9] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[10] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[11] 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[12] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[13] 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[14] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[15] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[16] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[17] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
[18] 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[19] 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(**) TRIDENT(0): Depth 16, (--) framebuffer bpp 16
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.3
(II) TRIDENT(0): Initializing int10
(II) TRIDENT(0): Primary V_BIOS segment is: 0xc000
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.3
(==) TRIDENT(0): RGB weight 565
(==) TRIDENT(0): Default visual is TrueColor
(==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0)
(**) TRIDENT(0): Option "SWcursor" "off"
(**) TRIDENT(0): Option "PciRetry" "off"
(**) TRIDENT(0): Option "NoAccel" "off"
(**) TRIDENT(0): Option "MUXThreshold" "10"
(**) TRIDENT(0): Option "ShadowFB" "on"
(**) TRIDENT(0): Option "NoMMIO" "on"
(**) TRIDENT(0): Option "NoPciBurst" "off"
(**) TRIDENT(0): Option "CyberShadow" "on"
(==) TRIDENT(0): Using HW cursor
(**) TRIDENT(0): MMIO Disabled
(**) TRIDENT(0): Cyber Shadow enabled
(**) TRIDENT(0): MUX Threshold set to 10
(**) TRIDENT(0): Using "Shadow Framebuffer" - acceleration disabled
(==) TRIDENT(0): Linear framebuffer at 0xFE400000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.3
(II) TRIDENT(0): VESA BIOS detected
(II) TRIDENT(0): VESA VBE Version 2.0
(II) TRIDENT(0): VESA VBE Total Mem: 4096 kB
(II) TRIDENT(0): VESA VBE OEM: Copyright 1994 TRIDENT MICROSYSTEMS INC.
(II) TRIDENT(0): VESA VBE OEM Software Rev: 0.0
(II) TRIDENT(0): VESA VBE OEM Vendor:
(II) TRIDENT(0): VESA VBE OEM Product:
(II) TRIDENT(0): VESA VBE OEM Product Rev:
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.3
(II) TRIDENT(0): VESA VBE DDC supported
(II) TRIDENT(0): VESA VBE DDC Level 2
(II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec.
(II) TRIDENT(0): VESA VBE DDC read failed
(--) TRIDENT(0): Revision is 35
(--) TRIDENT(0): Found Cyber 9397 chip
(--) TRIDENT(0): RAM type is SGRAM
(**) TRIDENT(0): VideoRAM: 4096 kByte
(--) TRIDENT(0): TFT Panel 800x600 found
(--) TRIDENT(0): Memory Clock is 83.00 MHz
(==) TRIDENT(0): Min pixel clock is 12 MHz
(**) TRIDENT(0): Max pixel clock is 170 MHz
(II) TRIDENT(0): My Monitor: Using hsync value of 35.15 kHz
(II) TRIDENT(0): My Monitor: Using vrefresh value of 56.70 Hz
(II) TRIDENT(0): Clock range: 12.00 to 170.00 MHz
(WW) TRIDENT(0): Default mode "640x350" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "640x400" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "720x400" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "640x480" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "640x480" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "640x480" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "640x480" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1024x768" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1024x768" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1024x768" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1024x768" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1024x768" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1152x864" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1280x960" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1280x960" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1280x1024" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1280x1024" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1280x1024" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1600x1200" deleted (hsync out of range)
(WW) TRIDENT(0): Default mode "1600x1200" deleted (bad mode clock/interlace/doublescan)
(WW) TRIDENT(0): Default mode "1600x1200" deleted (bad mode clock/interlace/doublescan)
(WW) TRIDENT(0): Default mode "1600x1200" deleted (bad mode clock/interlace/doublescan)
(WW) TRIDENT(0): Default mode "1600x1200" deleted (bad mode clock/interlace/doublescan)
(WW) TRIDENT(0): Default mode "1792x1344" deleted (insufficient memory for mode)
(WW) TRIDENT(0): Default mode "1792x1344" deleted (insufficient memory for mode)
(WW) TRIDENT(0): Default mode "1856x1392" deleted (insufficient memory for mode)
(WW) TRIDENT(0): Default mode "1856x1392" deleted (insufficient memory for mode)
(WW) TRIDENT(0): Default mode "1920x1440" deleted (insufficient memory for mode)
(WW) TRIDENT(0): Default mode "1920x1440" deleted (insufficient memory for mode)
(--) TRIDENT(0): Virtual size is 800x600 (pitch 800)
(**) TRIDENT(0): Mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(==) TRIDENT(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.2.0
ABI class: XFree86 Video Driver, version 0.3
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"
(II) Loading /usr/X11R6/lib/modules/libshadow.a
(II) Module shadow: vendor="The XFree86 Project"
compiled for 4.0.2, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0xfe800000 - 0xfebfffff (0x400000) MX[B]
[1] 0 0xfede0000 - 0xfedfffff (0x20000) MX[B]
[2] 0 0xfe400000 - 0xfe7fffff (0x400000) MX[B]
[3] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[4] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[5] -1 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0x60080000 - 0x60080000 (0x1) MX[B]
[9] -1 0x600c0000 - 0x600c0000 (0x1) MX[B]
[10] -1 0xf8000000 - 0xfbffffff (0x4000000) MX[B]
[11] -1 0xfe800000 - 0xfebfffff (0x400000) MX[B](B)
[12] -1 0xfede0000 - 0xfedfffff (0x20000) MX[B](B)
[13] -1 0xfe400000 - 0xfe7fffff (0x400000) MX[B](B)
[14] 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprU)
[15] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprU)
[16] 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprU)
[17] -1 0x00000000 - 0x000001ff (0x200) IX[B]E
[18] -1 0x00000400 - 0x00000400 (0x1) IX[B]
[19] -1 0x0000fce0 - 0x0000fcff (0x20) IX[B]
[20] -1 0x0000fcd0 - 0x0000fcdf (0x10) IX[B]
[21] 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[22] 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(==) TRIDENT(0): Write-combining range (0xfe400000,0x400000)
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(==) TRIDENT(0): Backing store disabled
(==) TRIDENT(0): Silken mouse enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(**) Option "Protocol" "PS/2"
(**) Mouse1: Protocol: "PS/2"
(**) Option "CorePointer"
(**) Mouse1: Core Pointer
(**) Option "Device" "/dev/psaux"
(==) Mouse1: Buttons: 3
(**) Option "Emulate3Buttons"
(**) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
(II) Keyboard "Keyboard1" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
(II) Open APM successful
(II) TRIDENT(0): Overriding Horizontal timings.
(II) TRIDENT(0): Timing shadow registers:0x7f 0x82 0x6b 0x1b 0x72 0xf8 0x58 0x8c 0x72 0x08
(II) TRIDENT(0): Setting BIOS Mode: 77
(II) TRIDENT(0): Shadow on
(II) TRIDENT(0): Forcing Shadow off
# File generated by xf86config.
#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
# Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
# This loads the GLX module
Load "glx"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
# FontPath "/usr/X11R6/lib/X11/fonts/truetype"
# FontPath "/usr/X11R6/lib/X11/fonts/misc/"
# FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
#FontPath "unix/127.0.0.1:7110"
FontPath "/usr/X11R6/lib/X11/fonts/TrueType/"
FontPath "/usr/lib/X11/fonts/misc/:unscaled"
FontPath "/usr/lib/X11/fonts/75dpi/:unscaled"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "Dont Zoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "Keyboard1"
Driver "Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
# Option "Protocol" "Xqueue"
Option "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""
# Option "XkbDisable"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc104"
Option "XkbLayout" "gb"
# Option "XkbCompat" ""
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/psaux"
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "My Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 35.15
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 56.7
Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
Section "Device"
Identifier "Trident Cyber 9397 (generic)"
Driver "trident"
VideoRam 4096
Option "SWCursor" "off"
Option "NoAccel" "off"
Option "PciRetry" "off"
Option "CyberShadow" "on"
Option "ShadowFB" "on"
#Option "VideoKey" "0" # hmmmmmm.......this is???
Option "NoPciBurst" "off"
#Option "SetMClk" "83Mhz" # strange behaviour
#Option "MUXThreshold" "<int>" # and this does....?
Option "NoMMIO" "on"
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "Trident Cyber 9397 (generic)"
Monitor "My Monitor"
DefaultDepth 16
Subsection "Display"
Depth 8
Modes "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 15
Modes "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "800x600"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Reply to: