[debian-knoppix] configuring the network under knoppix
Hello,
Because the Dell computer I use normally has a broken start button (at
the local hardware helpdesk no solution was provided...) I now have a
problem!
I now am forced to use this computer of my dad but it only has windows
xp and I really am not too happy.. I need compilers and stuff because
I'm a informatica student but nothing is available and cygwin sucks;
So I tried knoppix, and, appart from not being able to write to the
screen during loading/shutting down, it worked - everything except for
the netwerk. I use an adsl modem of which I know it's usable in knoppix:
on my own computer I use the same adsl modem;
I don't know anything about the netwerk card - it's only reported as
önbord 10/100 mbit network card" - but it uses the modem I normally use
so the only problem it can be is the netwerk card. I tried pppoe in
knoppix but no luck
I attached two output files, from lsmod output and dmesg output; And a
logfile containing output from `ping localhost`, `ifconfig -a` , `ping
10.0.0.138`, and I attached the error from `pppoe`
I hope someone can help me to get networking to work under knoppix!
thanks for your help,
Joris
Linux version 2.4.21-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Fre Jul 25 00:06:47 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
BIOS-e820: 000000000dff0000 - 000000000dff3000 (ACPI NVS)
BIOS-e820: 000000000dff3000 - 000000000e000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
223MB LOWMEM available.
found SMP MP-table at 000f6480
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 57328
zone(0): 4096 pages.
zone(1): 53232 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f7f70
RSD PTR v0 [AWARD ]
__va_range(0xdff3000, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [AWARD AWRDACPI 16944.11825]
__va_range(0xdff3040, 0x24): idx=8 mapped at ffff6000
__va_range(0xdff3040, 0x74): idx=8 mapped at ffff6000
ACPI table found: FACP v1 [AWARD AWRDACPI 16944.11825]
__va_range(0xdff6e00, 0x24): idx=8 mapped at ffff6000
__va_range(0xdff6e00, 0x68): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [AWARD AWRDACPI 16944.11825]
__va_range(0xdff6e00, 0x68): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0000] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) APIC version 16
LAPIC (acpi_id[0x0001] id[0x1] enabled[0])
CPU 1 (0x0100) disabled
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x0] trigger[0x0])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
2 CPUs total
Local APIC address fee00000
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz lang=us
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Initializing CPU#0
Detected 1792.760 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3578.26 BogoMIPS
Memory: 223576k/229312k available (1258k kernel code, 5348k reserved, 531k data, 132k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU0: Intel(R) Celeron(R) CPU 1.80GHz stepping 03
per-CPU timeslice cutoff: 365.71 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-17, 2-19, 2-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 18.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178014
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0014
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 69
0d 001 01 0 0 0 0 0 1 1 71
0e 001 01 0 0 0 0 0 1 1 79
0f 001 01 0 0 0 0 0 1 1 81
10 001 01 1 1 0 1 0 1 1 89
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 1 0 1 1 91
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 99
15 001 01 1 1 0 1 0 1 1 A1
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 A9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1792.7480 MHz.
..... host bus clock speed is 99.5969 MHz.
cpu: 0, clocks: 995969, slice: 497984
CPU0<T0:995968,T1:497984,D:0,S:497984,C:995969>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfbc60, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router SIS [1039/0008] at 00:02.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 18
PCI->APIC IRQ transform: (B0,I2,P2) -> 18
PCI->APIC IRQ transform: (B0,I3,P0) -> 20
PCI->APIC IRQ transform: (B0,I3,P1) -> 21
PCI->APIC IRQ transform: (B0,I3,P3) -> 23
PCI->APIC IRQ transform: (B0,I15,P0) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe0000000, mapped to 0xce80d000, size 12288k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at cb35:000c
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SiS651 ATA 133 controller
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD400JB-00ENA0, ATA DISK drive
hdc: CD-952E/AKV, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=4865/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
hdc: attached ide-scsi driver.
Partition check:
hda: hda1
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01-ww1
No raid array found
No raid array found
No raid array found
Guestimating sector 78164335 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: E-IDE CD Model: -952E/AKV Rev: A79
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 466k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18f (Release Date: Tue Dec 10 09:54:39 EST 2002)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v1.00
cloop: /cdrom/KNOPPIX/KNOPPIX: 29285 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 8 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
unloading Kernel Card Services
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 00:20:27 Jul 25 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-ohci.c: USB OHCI at membase 0xcf49b000, IRQ 20
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xcf49d000, IRQ 21
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usbdevfs: remount parameter error
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xcf4b5000, 00:0c:76:14:6b:fc, IRQ 18
eth0: Identified 8139 chip type 'RTL-8139C'
Intel 810 + AC97 Audio, version 0.24, 00:19:24 Jul 25 2003
i810: SiS 7012 found at IO 0xe400 and 0xe000, MEM 0x0000 and 0x0000, IRQ 18
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
i810_audio: AC'97 codec 0, new EID value = 0x05c7
i810_audio: AC'97 codec 0, DAC map configured, total channels = 6
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 176M
agpgart: Trying generic SiS routines for device id: 0651
agpgart: AGP aperture is 64M @ 0xe8000000
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Warning: Remapping obsolete /dev/fb* minor 32 to 1
Warning: Remapping obsolete /dev/fb* minor 64 to 2
Warning: Remapping obsolete /dev/fb* minor 96 to 3
Warning: Remapping obsolete /dev/fb* minor 128 to 4
Warning: Remapping obsolete /dev/fb* minor 160 to 5
Warning: Remapping obsolete /dev/fb* minor 192 to 6
Warning: Remapping obsolete /dev/fb* minor 224 to 7
i810_audio: drain_dac, dma timeout?
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Module Size Used by Not tainted
autofs4 8724 1 (autoclean)
af_packet 13448 0 (autoclean)
nls_iso8859-1 2876 1 (autoclean)
nls_cp437 4380 1 (autoclean)
agpgart 34592 0 (unused)
i810_audio 25064 0
ac97_codec 10696 0 [i810_audio]
soundcore 3364 2 [i810_audio]
8139too 17160 1
mii 2192 0 [8139too]
serial 51844 0 (autoclean)
usb-ohci 18152 0 (unused)
usbcore 57376 1 [usb-ohci]
apm 9768 2
rtc 6908 0 (autoclean)
cloop 7940 2
knoppix@ttyp0[knoppix-configuring]$ ping localhost
PING Knoppix (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.1 ms
64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=3 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=4 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=5 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=6 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=7 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=8 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=9 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=10 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=11 ttl=64 time=0.0 ms
64 bytes from 127.0.0.1: icmp_seq=12 ttl=64 time=0.0 ms
--- Knoppix ping statistics ---
13 packets transmitted, 13 packets received, 0% packet loss
round-trip min/avg/max = 0.0/0.0/0.1 ms
knoppix@ttyp0[knoppix-configuring]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:0C:76:14:6B:FC
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:18 Base address:0x5000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:32 errors:0 dropped:0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2484 (2.4 KiB) TX bytes:2484 (2.4 KiB)
knoppix@ttyp0[knoppix-configuring]$ ping 10.0.0.138
PING 10.0.0.138 (10.0.0.138): 56 data bytes
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
ping: sendto: Network is unreachable
ping: wrote 10.0.0.138 64 chars, ret=-1
--- 10.0.0.138 ping statistics ---
8 packets transmitted, 0 packets received, 100% packet loss
root@ttyp0[knoppix-configuring]# pppoe
pppoe: Timeout waiting for PADO packets
Sorry, I scanned 1 interface(s), but the Acces
Concentrator of your provider did not respond. Please
check your network and modem cables. Another reason
for the scan failure may also be another running
pppoe process which controls the modem.
Reply to: